Project

General

Profile

Actions

OpenBSC GPRS » History » Revision 27

« Previous | Revision 27/37 (diff) | Next »
wirelesss, 01/05/2017 11:51 AM


OpenBSC GPRS/EDGE Setup page

Pre-requisites

  • BTS hardware: sysmoBTS, USRP, UmTRX, nanoBTS with GPRS or EDGE support. BS11 are not supported.
  • A compiled GGSN from OpenGGSN
  • A working and up-to-date OpenBSC (see Building_OpenBSC)
    • You will need to (re-)build it after having installed OpenGGSN so that the libgtp is detected and the SGSN binary osmo-sgsn built.
  • A custom SIM for your network
    • Currently OsmoSGSN refuses all roaming, so you need a SIM that matches your custom MCC/MNC network

Setup

First a little picture to illustrate the different elements and their interactions :

Compiling OpenBSC with [E]GPRS

The guide below was tested on Ubuntu 15.10 but should work on Debian as well.

First you need to download all dependencies:

apt install libdbi0-dev libdbd-sqlite3 libtool autoconf git-core pkg-config make libortp-dev

Please follow instructions provided at Build from source in order to install these projects:

  • openggsn
  • libosmocore
  • libosmo-abis
  • libosmo-netif
  • openbsc
  • osmo-pcu

OpenBSC configuration

The first step is to configure OpenBSC for gprs support. Add this to the network/bts node in openbsc.cfg:

gprs mode gprs
gprs routing area 0
gprs cell bvci 2
gprs nsei 101
gprs nsvc 0 nsvci 101
gprs nsvc 0 local udp port 23000
gprs nsvc 0 remote udp port 23000
gprs nsvc 0 remote ip 192.168.0.128

The gprs nsvc 0 remote entries 192.168.0.128:23000 is the IP/port of the machine running the SGSN as seen from the BTS. It will be sent by OpenBSC to the BTS in the configuration phase and the BTS will connect back to the SGSN.

The second step is to allocate some timeslots to packet data. For this, just change the 1 or more network/bts/trx/timeslot nodes using :

phys_chan_config PDCH

OsmoSGSN configuration

Here's a sample SGSN configuration file osmo-sgsn.cfg with some explanations :

!
! Osmocom SGSN configuration
!
!
line vty
 no login
!
sgsn
 gtp local-ip 192.168.1.128
 ggsn 0 remote-ip 192.168.1.129
 ggsn 0 gtp-version 1
!
ns
 timer tns-block 3
 timer tns-block-retries 3
 timer tns-reset 3
 timer tns-reset-retries 3
 timer tns-test 30
 timer tns-alive 3
 timer tns-alive-retries 10
 encapsulation udp local-ip 192.168.0.128
 encapsulation udp local-port 23000
 encapsulation framerelay-gre enabled 0
!
bssgp
!
  • The gtp local-ip entry is the local IP the SGSN will bind to.
  • The ggsn 0 remote-ip entry if the remote IP of the GGSN. The SGSN will connect to it.
  • Those two IPs must be different even if you're running both processes on the same machine. A solution for that is to put several IP aliases on the same network interface or use the loopback interface.
  • The encapsulation settings must be the same IP/port than you've setup in openbsc.cfg

OpenGGSN configuration

The ggsn.conf file is pretty well documented. What is mostly of interest here is :

  • The configuration of the GTP link. (Must match the ggsn 0 remote-ip entry in osmo-sgsn.cfg)
# TAG: listen
# Specifies the local IP address to listen to
listen 192.168.1.129
  • The configuration given to phones, IP pool & DNS.
# TAG: dynip
# Dynamic IP address pool.
# Used for allocation of dynamic IP address when address is not given
# by HLR.
# If this option is not given then the net option is used as a substitute.
# dynip 192.168.254.0/24

# TAG: pcodns1/pcodns2
# Protocol configuration option domain name system server 1 & 2.
pcodns1 208.67.222.222
pcodns2 208.67.220.220

OsmoPCU configuration

pcu
 flow-control-interval 10
 cs 2
 alloc-algorithm dynamic
 alpha 0
 gamma 0

Network configuration

You will also need to configure some networking rules to allow connectivity from tun0. Look up linux networking/nat howtos on google.

Modern systems

Add following setting to /etc/systemd/network:

wired.network:

[Match]
Name=enp2s0

[Network]
DHCP=ipv4
IPMasquerade=yes

tun.network:

[Match]
Name=tun0

[Network]
Address=192.168.0.1
IPMasquerade=yes

The setup above assume that you're using interface enp2s0 to access the internet from the machine which runs openggsn. Notice the IPMasquerade option on both interfaces. This also assume the default 192.168.0.1/24 ip address range used by openggsn. If your situation differs - adjust accordingly using https://www.freedesktop.org/software/systemd/man/systemd.network.html as a reference.

Legacy systems

The basic setup for testing only in a safe environment would be :

sh# echo 1 > /proc/sys/net/ipv4/ip_forward
sh# iptables -A POSTROUTING -s 192.168.254.0/24 -t nat -o eth0 -j MASQUERADE

(replace eth0 by the interface providing your machine connectivity)

DNS issues

In some cases the DNS server might be hardcoded in the phones APN settings. To work around this problem one might choose to enforce the usage of a specific DNS server by redirecting all DNS traffic via iptables:

sh# iptables -t nat -I PREROUTING -i tun0 -p udp --dport 53 -j DNAT --to-dest 1.2.3.4

(replace 1.2.3.4 with the ip-address of your DNS-Server)

You can put this into .sh file and reference it from openggsn config using

ipup /full/path/to/your.sh

Running

Sample startup sequence (adjust logging and configuration files location as you see fit):

osmo-nitb -s -c ~/.config/osmocom/open-bsc.cfg -l ~/.config/osmocom/hlr.sqlite3 -P -m -C -T --debug=DSQL:DLSMS:DRLL:DCC:DMM:DRR:DMSC:DHO:DGPRS:DNS:DLLC:DCTRL 2>&1 | tee /tmp/openbsc.log
sudo ggsn -c ~/.config/osmocom/ggsn.conf -f -d
osmo-sgsn -c ~/.config/osmocom/osmo-sgsn.cfg -d DRLL:DCC:DMM:DRR:DNM:DMSC:DHO:DGPRS:DNS:DLLC:DCTRL

cd osmo-trx/Transceiver52M
sudo chrt 20 ./osmo-trx
cd osmo-bts/src/osmo-bts-trx
sudo chrt 15 ./osmobts-trx -c ~/.config/osmocom/osmo-bts.cfg -i 224.0.0.1 -d DRLL:DCC:DMM:DRR:DNM:DMSC:DHO:DGPRS:DNS:DLLC:DCTRL

osmo-pcu/src
sudo ./osmo-pcu -c ~/.config/osmocom/osmo-pcu.cfg

Note: OsmoTRX is only necessary with USRP/UmTRX transceivers (At the time of writing 201509-fairwaves-rebase branch of OsmoBTS is necessary as well for compatibility).

Once you're done with experimenting and ready for production setup it might be convenient to create systemd units so all the parts are started automatically.

Authorization Policy

Authorization determines whether particular subscriber can access your network or not.

The following 4 authorization policy options are available:

  • accept-all: When this option is selected then all IMSIs will be accepted. Using this policy option can be dangerous.
  • acl-only: In this case you will allow SGSN to accept only IMSIs, which are explicitly white-listed by the Access Control List (ACL) and the rest will be rejected.
  • closed: This option allows you to accept only home network subscribers either the ones, which are in the ACL or MCC/MNC match. (i.e. MCC 901, MNC 700, IMSI 901700000003080).
  • remote: When this authorization option is selected then the GSUP protocol to remotely access a HLR will be used. Remote subscription data only will be used.

Example: How to assign or change current authorization policy follows below:

OsmoSGSN> enable
OsmoSGSN# configure terminal
OsmoSGSN(config)# sgsn
OsmoSGSN(config-sgsn)# auth-policy acl-only 
OsmoSGSN(config-sgsn)# write
Configuration saved to sgsn.cfg
OsmoSGSN(config-sgsn)# exit
OsmoSGSN(config)# exit
OsmoSGSN# disable
OsmoSGSN>

In the example acl-olny is selected as authorization policy.
After this we are saving current changes to configuration file using command write to make this policy persistent.

Other authorization policy option can be selected by using the above given example. Just state, which authorization policy option you would like to use.

Troubleshooting

  • double-check that your phones have APN set to something. "Internet" will do for example. The value of APN is not checked but if it's unset the phones' baseband might not even try to initiate GPRS connection.
You can access vty from
Files (4)
gprs.png View gprs.png 26 KB General GPRS setup tnt, 06/10/2010 01:35 PM
gprs.2.png View gprs.2.png 26.1 KB , 01/12/2012 10:47 AM
gprs_example_config.tar gprs_example_config.tar 20 KB complete set of config files including README for working GPRS data service neels, 10/06/2016 07:50 PM
gprs.3.png View gprs.3.png 31.3 KB pespin, 04/04/2017 01:22 PM

Updated by wirelesss about 7 years ago · 27 revisions

Add picture from clipboard (Maximum size: 48.8 MB)