Project

General

Profile

Osmocom Network In The Box » History » Revision 93

Revision 92 (neels, 12/07/2017 03:25 PM) → Revision 93/163 (neels, 12/07/2017 03:39 PM)

{{>toc}} 

 h1. Osmocom Network In The Box 

 This is a brief guide to the most basic and minimal setup of an Osmocom 2G and/or 3G network for voice and data services. It is a good starting point for newcomers to familiarize with the software, and to expand upon by the [[Osmocom Manuals]] and other wiki pages. 

 h1. OsmoNITB R.I.P., long live the Network In The Box 

 Historically, Osmocom offered the [[OsmoNITB:]] "Network-In-The-Box" as an actual single program. It was a useful simplification at the time, but in 2017, Osmocom have decided to split OsmoNITB into programs more closely resembling traditional network architecture. It is recommended to use the new separate components instead of the OsmoNITB, since active development focus has moved there. 

 It is still very much possible to run a complete Osmocom core network in one "box". For example, a sysmoBTS can run the entire core network on the same hardware that drives the TRX, making it a complete network in actually one single box. At the same time, having separate components also allows scaling to large deployments, with properly distributed load and a central subscriber database. 

 To migrate from OsmoNITB to the new separate programs, see the [[OsmoNITB Migration Guide]]. 

 

 h1. Part of this Complete Network 

 Assuming that you have your radio hardware ready (a BTS, a femto cell or an SDR driven by osmo-trx), the core network consists of separate programs providing voice/SMS/USSD ("circuit-switched" or CS) and data ("packet-switched" or PS) services. 

 Here is a table of the components you need: 

 |\4. *Required for*    |/3. *Program* |/3. *Description* | 
 |\2. *2G*    |\2. *3G* | 
 | *CS* | *PS* | *CS* | *PS* | 
 | ✔ | ✔ | ✔ | ✔ | [[Osmocom Network In The Box#OsmoHLR|OsmoHLR]] | Home Location Register, stores subscriber IMSI, phone number and auth tokens. | 
 | ✔ | (1) | ✔ | (1) | [[Osmocom Network In The Box#OsmoMSC|OsmoMSC]] | Mobile Switching Center, handles signalling, i.e. attach/detach of subscribers, call establishment, messaging (SMS and USSD). | 
 | ✔ |     | ✔ |     | [[Osmocom Network In The Box#OsmoMGW|OsmoMGW]] | Media Gateway, is instructed by the MSC and/or the BSC to direct RTP streams for active voice calls. | 
 | ✔ | ✔ | ✔ | ✔ | [[Osmocom Network In The Box#OsmoSTP|OsmoSTP]] | Signal Transfer Point, routes SCCP messages between MSC, BSC, HNBGW and for 3G also the SGSN. | 
 | ✔ | (1) |     |     | [[Osmocom Network In The Box#OsmoBSC|OsmoBSC]] | 2G Base Station Controller, manages logical channels and other lower level aspects for one or more 2G BTS; it is technically part of the BSS and not the "core network". | 
 |     |     | ✔ | ✔ | [[Osmocom Network In The Box#OsmoHNBGW|OsmoHNBGW]] | 3G HomeNodeB Gateway, receives the Iuh protocol from a 3G femto cell and forwards to MSC and SGSN by SCCP/M3UA via OsmoSTP. | 
 |     | ✔ (2) |     | ✔ (2) | [[Osmocom Network In The Box#OsmoGGSN|OsmoGGSN]] | Gateway GPRS Support Node, "opens" GTP tunnels received from SGSNs to internet uplink. | 
 |     | ✔ |     | ✔ | [[Osmocom Network In The Box#OsmoSGSN|OsmoSGSN]] | Serving GPRS Support Node, handles signalling, i.e. attach/detach of subscribers and PDP contexts. | 
 | ✔ | (1) |     |     | [[Osmocom Network In The Box#OsmoBTS|OsmoBTS]] | for 2G networks, drives the TRX and ties to the BSC via Abis-interface. | 
 |     | ✔ |     |     | [[Osmocom Network In The Box#OsmoPCU|OsmoPCU]] | for 2G networks, a component closely tied to the BTS, drives the TRX for PS timeslots and ties to the SGSN via Gb-interface. | 
 |     |     | ✔ | ✔ | hNodeb | 3rd party 3G femto cell hardware to connect to OsmoHNBGW via Iuh | 

 1: PS is always an _addition_ to CS: even though these components do not handle PS requests, you need to have these to be able to setup and register with a network, which is a prerequisite for data services. 

 2: For the GGSN to successfully route packets to an internet uplink, it needs a tun device set up and usually IP masquerading/forwarding enabled. Please refer to the OsmoGGSN manual for more details. 

 h2. Topology 

 {{graphviz_link() 
 digraph G { 
   rankdir = LR; 
  
   MS [label="MS\n(2G phone)"] 
   UE [label="UE\n(3G phone)"] 

   subgraph cluster_bts { 
     BTS [rank="min"] 
     PCU [rank="min"] 
   } 

   subgraph cluster_msc_mgw { 
     label=MGCP;style=dotted 
     MSC 
     MGW1 [label="MGW"] 
   } 

   subgraph cluster_bsc_mgw { 
     label=MGCP;style=dotted 
     BSC 
     MGW2 [label="MGW"] 
   } 

   hNodeB [shape="box",label="hNodeB\n(3G femto cell)"] 

   MS -> BTS [label="Um"] 
   MS -> PCU [style="dashed"] 
 
   BTS -> BSC [label="Abis/IP"] 
   STP [label="STP\n(SCCP/M3UA)"] 
   BSC -> STP -> MSC [label="A"] 
   MSC -> HLR [label="GSUP"] 
   SGSN -> HLR [label="GSUP",style="dashed"] 
   UE -> hNodeB [label="Uu"] 
   UE -> hNodeB [style="dashed"] 
   hNodeB -> HNBGW [label="Iuh"] 
   HNBGW -> STP -> MSC [label="IuCS"] 
   HNBGW -> STP -> SGSN [label="IuPS",style="dashed"] 
   PCU -> SGSN [label="Gb",style="dashed"] 
   SGSN -> GGSN [label="GTP-C",style="dashed"] 
   SGSN -> GGSN [label="GTP-U(2G)",style="dashed"] 
   hNodeB -> GGSN [label="GTP-U(3G)",style="dashed"] 
   GGSN -> internet [label="tun",style="dashed"] 

   BTS -> MGW2 -> MGW1 [label="RTP"] 
   MGW1 -> MGW1 [label="RTP"] 
   hNodeB -> MGW1 [label="IuUP/RTP"] 

   A, B, C, D [style="invisible"] 
   A -> B [label="data (PS)",style="dashed"] 
   C -> D [label="voice (CS)"] 

 } 
 }} 

 

 h1. Have to Know 

 Each program features a detailed [[Osmocom Manuals|user manual]], your primary source of information to expand on the setup described here. 

 Osmocom offers [[Binary_Packages|compiled packages for various distributions]]. If you're up to it, you may also [[Build from Source]]. 

 Each Osmocom program typically has 

 * a distinct configuration file; 
 * a VTY telnet console for live interaction; 
 * a CTRL interface for live interaction from 3rd party programs. 

 See [[Port Numbers]] to find out which program runs VTY on which port. 

 h1. Configuration Examples 

 Here is a tarball of the config files discussed below: attachment:nitb.tar 

 h2. OsmoHLR 

 [[OsmoHLR:]] is the Home Location Register: it Register, stores subscriber IMSI, phone number and auth tokens. This is where you configure who is allowed on your network and who has which phone number. 

 osmo-hlr will automatically bootstrap an empty subscriber database. See the [[Osmocom Manuals|manual]] on how to add one or more subscribers -- if you don't know your IMSI, it can be useful to attempt a connection and watch the OsmoHLR log for a rejected IMSI. To migrate subscribers from an older OsmoNITB database, see the [[OsmoNITB migration guide]]. 

 While you do need one, your configuration file may actually remain empty. This will serve GSUP on localhost (127.0.0.1), sufficient for a Network In The Box with MSC and SGSN on the same machine as the HLR. 

 *osmo-hlr.cfg* 
 <pre> 
 # empty, the defaults are sufficient 
 </pre> 

 h2. OsmoMSC 

 [[OsmoMSC:]] is the Mobile Switching Center: it Center, handles signalling, i.e. attach/detach of subscribers, call establishment, messaging (SMS and USSD). The OsmoMSC is your central "manager" of the network. 

 The VLR component of OsmoMSC needs to connect to the OsmoHLR's GSUP server to know which subscribers are authorized. By default, it will connect to OsmoHLR on localhost, no explicit config needed. 

 To be reachable by OsmoBSC and OsmoHNBGW, OsmoMSC needs an SCCP point code, and it needs to connect to OsmoSTP to make itself known to SCCP routing. 

 * There is a default point code, currently 0.23.1 (in 8.8.3 point code format, see [[Point Codes]]). 
 * OsmoMSC will by default look for OsmoSTP on localhost's M3UA port, 2905. 

 To direct RTP streams, OsmoMSC needs an OsmoMGW instance (see OsmoMGW below). 

 You only need to set up your MCC, MNC, and how to reach/use the MGW. 

 *osmo-msc.cfg* 
 <pre> 
 network 
  network country code 901 
  mobile network code 70 
 msc 
  mgw remote-ip 192.168.0.9 
  mgw endpoint-range 1 32 
 </pre> 

 h2. OsmoMGW 

 [[OsmoMGW:]] is the Media Gateway: it Gateway, is instructed by the MSC and/or the BSC to direct RTP streams for active voice calls. The Media Gateway receives instructions in the form of MGCP messages from OsmoMSC/OsmoBSC. It forwards RTP streams directly between BTS, femto cells and remote endpoints, e.g. other MGW instances, and its job is to transcode between codecs (future). 

 You need an OsmoMGW to serve OsmoMSC's MGCP requests, and an OsmoMGW to serve OsmoBSC's MGCP requests. In fact, these two can be served by one single OsmoMGW instance. If you would like to keep two separate OsmoMGW instances, you need to take care that they don't attempt to bind to identical ports on the same IP address (for MGCP, but also for VTY and CTRL interfaces). 

 Consider that you have a 2G network with an external BTS (say a sysmoBTS), which means that you need your OsmoBSC's MGW instance to be reachable on a public interface. So far the MSC's MGW can be on a local loopback interface, it only needs to be reachable by the BSC's MGW and by the MSC. 

 If you also have a 3G femto cell, then the MSC's MGW instance also needs to be on a public interface. At this point you either need two public interface addresses, or you need to put one of the MGWs on a different MGCP port. 

 If you use one OsmoMGW for both BSC and MSC, there are no port conflicts, but you need to take care that MSC and BSC use differing endpoint identifiers, or they will interfere with each others' RTP stream configurations. 

 To increase the likelihood that your first setup will work out, below examples pick distinct endpoint ranges so that MSC and BSC could use the same MGW instance, while at the same time provide config files that allow running two MGWs on the same public IP address. 

 h3. OsmoMGW for OsmoMSC 

 *NOTE: Currently, OsmoMSC still requires the legacy osmo-bsc_mgcp program, which will move to the new osmo-mgw soon. osmo-bsc_mgcp is still available from osmo-mgw.git. For osmo-bsc_mgcp, you can use the identical config as shown for the MSC's MGW here.* 

 * In a setup that truly runs in one box (e.g. sysmoBTS or osmo-trx with co-located core network), this may be localhost (127.0.0.1), which is the default, and your config file may omit the 'bind ip'. 
 * With a separate BTS and/or RNC (e.g. 3G femto cell or nanoBTS), make sure to configure an IP address that is reachable by the hNodeB and BTS: 

 *osmo-mgw-for-msc.cfg* 
 <pre> 
 mgcp 
  bind ip 192.168.0.9 
  number endpoints 64 
 line vty 
  bind 127.0.0.1 
 </pre> 

 h3. OsmoMGW for OsmoBSC 

 OsmoBSC also requires an OsmoMGW instance to run alongside it. In a setup where OsmoBSC and OsmoMGW run on the same box, they may in fact share the same OsmoMGW instance, as long as BSC and MSC use different endpoint identifiers. 

 It is semantically more clear to run a separate OsmoMGW instance for the OsmoBSC, which then needs to not interfere with the other MGW's ports, for example: 

 *osmo-mgw-for-bsc.cfg* 
 <pre> 
 mgcp 
  bind ip 192.168.0.9 
  # default port is 2427 (is used for MSC's MGW) 
  bind port 12427 
  number endpoints 64 
 line vty 
  # default VTY interface is on 127.0.0.1 (used for MSC's MGW) 
  bind 127.0.0.2 
 </pre> 

 Note that osmo-bsc.cfg below sets the 'mgw remote-port' to the 'bind port' configured here (the method to run two MGW on the same public IP address), and picks a different 'mgw endpoint' range than the OsmoMSC (the method to use the same MGW for both BSC and MSC) -- these are two separate, redundant measures, and you usually would pick only one of them. 

 h2. OsmoSTP 

 [[OsmoSTP:]] is the Signal Transfer Point: it Point, acts as a server for routing SCCP messages. OsmoMSC, OsmoBSC, OsmoHNBGW and OsmoSGSN contact OsmoSTP and announce their own point code, after which they may instruct OsmoSTP to route SCCP messages to each other by these point codes. 

 The basic configuration that permits dynamic routing is: 

 *osmo-stp.cfg* 
 <pre> 
 cs7 instance 0 
  xua rkm routing-key-allocation dynamic-permitted 
  listen m3ua 2905 
   accept-asp-connections dynamic-permitted 
 </pre> 

 h2. OsmoBSC 

 [[OsmoBSC:]] is the 2G Base Station Controller: it Controller, manages logical channels and other lower level aspects for one or more 2G BTS. The BSC tells the MSC what the phones would like to do, and in turn the MSC tells the BSC to establish channels, page phones, and take care of the lower level BTS maintenance. 

 OsmoBSC needs to register with OsmoSTP, and contact the MSC by its point code. If not configured otherwise, it will use OsmoMSC's default point code to contact it, see [[Point Codes]]. 

 OsmoBSC needs to contact an OsmoMGW to direct RTP streams between BTS and the MSC's MGW, as discussed above under "OsmoMGW". 

 OsmoBSC also needs complete configuration of all connected BTS. This example shows configuration for a sysmoBTS. 

 Furthermore, some network properties need to be set. 

 The 'gprs mode' determines whether packet switched access will be enabled. 'gprs mode none' switches off data services, it tells osmo-bts not to contact osmo-pcu to establish data service. 

 To allow data service, set a 'gprs mode gprs' or 'gprs mode egprs', and configure PDCH timeslots. Traditionally, a fixed amount of TCH timeslots for voice and PDCH timeslots for data service are configured. OsmoBTS also supports two types of dynamic timeslots, as described in the "Abis manual":http://ftp.osmocom.org/docs/latest/osmobts-abis.pdf, chapter "Dynamic Channel Combinations". The following is a configuration with voice-and-data service based on Osmocom style dynamic timeslots: 

 *osmo-bsc.cfg* for voice and data service 
 <pre> 
 network 
  network country code 901 
  mobile network code 70 
  mm info 1 
  short name OsmoBSC 
  long name OsmoBSC 
  bts 0 
   type sysmobts 
   band GSM-1800 
   location_area_code 23 
   ip.access unit_id 1800 0 
   gprs mode gprs 
   gprs nsvc 0 remote ip 192.168.0.9 
   gprs nsvc 0 remote udp port 23000 
   gprs nsvc 0 local udp port 23000 
   gprs nsvc 0 nsvci 1800 
   gprs nsei 1800 
   gprs cell bvci 1800 
   trx 0 
    rf_locked 0 
    arfcn 868 
    nominal power 23 
    timeslot 0 
     phys_chan_config CCCH+SDCCH4 
    timeslot 1 
     phys_chan_config SDCCH8 
    timeslot 2 
     phys_chan_config TCH/F_TCH/H_PDCH 
    timeslot 3 
     phys_chan_config TCH/F_TCH/H_PDCH 
    timeslot 4 
     phys_chan_config TCH/F_TCH/H_PDCH 
    timeslot 5 
     phys_chan_config TCH/F_TCH/H_PDCH 
    timeslot 6 
     phys_chan_config TCH/F_TCH/H_PDCH 
    timeslot 7 
     phys_chan_config PDCH 
 e1_input 
  e1_line 0 driver ipa 
 msc 0 
  mgw remote-ip 192.168.0.9 
  mgw remote-port 12427 
  mgw endpoint-range 33 64 
  allow-emergency deny 
  codec-list hr3 
 </pre> 

 

 h2. OsmoHNBGW 

 [[OsmoHNBGW:]] is the 3G HomeNodeB Gateway, found Gateway (found in the osmo-iuh.git repository: it repository), receives the Iuh protocol from a 3G femto cell, separates it into IuCS and IuPS and forwards to the MSC and SGSN. 

 OsmoHNBGW needs to connect to OsmoSTP for routing, and needs to know the MSC and SGSN point codes. If omitted, it assumes OsmoSTP on 127.0.0.1 and uses the point codes that are default in OsmoMSC and OsmoSGSN, see [[Point Codes]]. 

 It must also be reachable by the hNodeB, hence its Iuh must typically run on a public IP, not a loopback address like 127.0.0.1. 

 *osmo-hnbgw.cfg* 
 <pre> 
 hnbgw 
  iuh 
   local-ip 192.168.0.9 
 </pre> 

 

 h2. OsmoGGSN 

 [[OpenGGSN:|OsmoGGSN]] is the Gateway GPRS Support Node: it Node, "opens" GTP tunnels received from SGSNs to internet uplink. To provide packet switched service, OsmoGGSN must offer GTP service to the OsmoSGSN. 

 Notably, both OsmoGGSN and OsmoSGSN must use identical port numbers, which is an intrinsic requirement of the GTP protocol. Hence they must not run on the same IP address. Furthermore, for 2G networks, the SGSN must be reachable by the PCU and thus needs to be on a public interface if the BTS is a separate box; for 3G networks, the GGSN must be reachable by the hNodeB and thus needs to be on a public interface. So, to cover both, you need to have *two* public interfaces; this example uses 192.168.0.42, made available by 

 <pre> 
 sudo ip addr add 192.168.0.42/32 dev eth0 
 </pre> 

 This is of course blatantly ignoring the local DHCP server's authority, just a quick hack. 

 OsmoGGSN maintains a gsn_restart counter, to be able to reliably communicate to the SGSN that it has restarted. This is kept in the 'state-dir', by default in /tmp. 

 It also needs access to a tun device with an address range available to subscribers' PDP contexts. This may be configured ahead of time, so that OsmoGGSN does not need root privileges. If run with 'sudo', OsmoGGSN may also create its own tun device. In below example, the 'apn0' device has been created ahead of time, with: 

 <pre> 
 sudo ip tuntap add dev apn0 mode tun user $USER group $USER 
 sudo ip addr add 192.168.42.0/24 dev apn0 
 sudo ip link set apn0 up 
 </pre> 

 IPv4 operation is enabled by default, but for future compatibility, it is good to indicate that explicitly. 

 OsmoGGSN furthermore indicates DNS servers, as well as an IPv4 address range to assign to subscribers' PDP contexts. 

 Note that the APN named in this config file (here "internet") needs to be configured on your phone, see [[Osmocom Network In The Box#APN-for-Data-Service|APN for Data Service]] below. With the @default-apn@ command, any unknown APN name will use that default APN instead, but still you usually have to define _some_ APN on your phone so that it even tries to connect to the data service. 

 A profound part of GGSN configuration is the network setup of your system: you need to allow the packets to be routed between the subscribers and your internet uplink. See the [[Osmocom Manuals|OsmoGGSN User Manual]], section _Running OsmoGGSN_ / _Routing_. 

 *osmo-ggsn.cfg* 
 NOTE: this configuration requires running osmo-ggsn with root privileges, as well as IP-forwarding and masquerading to be enabled 
 <pre> 
 ggsn ggsn0 
  gtp bind-ip 192.168.0.42 
  apn internet 
   tun-device apn0 
   type-support v4 
   ip dns 0 192.168.0.1 
   ip dns 1 8.8.8.8 
   ip prefix dynamic 192.168.42.0/24 
   no shutdown 
  default-apn internet 
  no shutdown ggsn 
 </pre> 

 h2. OsmoSGSN 

 [[OsmoSGSN:]] is the Serving GPRS Support Node: it Node, handles signalling, i.e. attach/detach of subscribers and PDP contexts for data services. 

 OsmoSGSN needs to reach the GGSN to establish GTP tunnels for subscribers. It must have a separate GTP IP address from OsmoGGSN, as mentioned before. 

 For 2G, OsmoSGSN needs to be reachable by the PCU, and needs a public IP for the Gb interface if it is not running directly on the BTS hardware (e.g. on sysmoBTS or when using osmo-trx). For 2G operation, SGSN and GGSN may both use a local IP address for GTP, as long as they differ (e.g. 127.0.0.1 and 127.0.0.2). 

 For 3G, OsmoSGSN needs to be reachable by both the HNBGW for IuPS as well as by the hNodeB for GTP, i.e. it definitely needs to have a public IP address for the GTP port. 

 For 3G IuPS, the SGSN must sign up at OsmoSTP with a point code that the HNBGW knows. If not configured explicitly, the respective defaults are used, see [[Point Codes]]. 

 Finally, OsmoSGSN needs access to OsmoHLR to access subscriber data. Set 'auth-policy remote' to use the HLR for subscriber authorization. The default  

 *osmo-sgsn.cfg* 
 <pre> 
 sgsn 
  gtp local-ip 192.168.0.9 
  ggsn 0 remote-ip 192.168.0.42 
  ggsn 0 gtp-version 1 
  auth-policy remote 
  gsup remote-ip 127.0.0.1 
 ns 
  encapsulation udp local-ip 192.168.0.9 
  encapsulation udp local-port 23000 
  encapsulation framerelay-gre enabled 0 
 </pre> 

 The @auth-policy remote@ requires that you have the SIM cards' authentication tokens in your OsmoHLR database. Instead, you can use @auth-policy accept-all@, but be aware that this will only work for 2G. 3G networks _require_ successful authentication, and @auth-policy remote@ is your _only_ option for a 3G SGSN. 

 h1. OsmoBTS 

 [[OsmoBTS:]] operates 2G radio hardware. OsmoBTS supports various hardware platforms including sysmoBTS and USRP. Instead, you may choose BTS vendors like ip.access or Siemens, which can also directly operate with OsmoBSC without OsmoBTS being involved. 

 The BTS needs to know where to reach OsmoBSC's Abis interface, and its unit id needs to match one of the BTS unit ids configured at OsmoBSC. 

 An example configuration for a sysmoBTS is: 

 <pre> 
 phy 0 
  instance 0 
 bts 0 
  band 1800 
  ipa unit-id 1800 0 
  oml remote-ip 192.168.0.9 
  trx 0 
   phy 0 instance 0 
 </pre> 

 h1. OsmoPCU 

 [[OsmoPCU:]] operates the packet-switched part of 2G radio hardware. Timeslots used for data transmission are controlled by the PCU instead of the BTS. OsmoPCU is typically configured from the @gprs@ config items in OsmoBSC, which is communicated to the PCU via OML and OsmoBTS (via the PCU socket). An example configuration for OsmoPCU would be: 

 <pre> 
 pcu 
  flow-control-interval 10 
  cs 2 
  alloc-algorithm dynamic 
  alpha 0 
  gamma 0 
  two-phase-access 
 </pre> 

 h1. Running Examples 

 Each Osmocom program comes with a systemd service file. It is recommended to place config files in /etc/osmocom/ and launch the individual components using systemd. 

 When installed from debian or opkg feeds, you will find the systemd service files in /lib/systemd/system/. 

 Re/starting and stopping then works like this: 

 <pre> 
 systemctl restart osmo-hlr 
 systemctl stop osmo-hlr 
 </pre> 

 It can be useful to have an @osmo-all@ script to re/start or stop all components at once, edit to pick yours: 

 *osmo-all* script 
 <pre> 
 #!/bin/sh 
 cmd="${1:-start}" 
 set -ex 
 systemctl $cmd osmo-hlr osmo-msc osmo-mgw osmo-ggsn osmo-sgsn osmo-stp osmo-bsc osmo-hnbgw osmo-bts-sysmo osmo-pcu  
 </pre> 

 which allows 

 <pre> 
 ./osmo-all restart 
 ./osmo-all status 
 ./osmo-all stop 
 </pre> 

 For illustration, the manual command invocations for the components would look like this: 

 <pre> 
 osmo-hlr -l hlr.db -c osmo-hlr.cfg 
 osmo-msc -c osmo-msc.cfg 
 osmo-mgw -c osmo-mgw-for-msc.cfg 
 osmo-mgw -c osmo-mgw-for-bsc.cfg 
 osmo-ggsn -c osmo-ggsn.cfg 
 osmo-sgsn -c osmo-sgsn.cfg 
 osmo-stp -c osmo-stp.cfg 
 osmo-bsc -c osmo-bsc.cfg 
 osmo-hnbgw -c osmo-hnbgw.cfg 
 # on a 2G sysmoBTS: 
 osmo-bts-sysmo -c osmo-bts.cfg -s -M 
 osmo-pcu -c osmo-pcu.cfg 
 </pre> 

 h1. Logging Examples 

 Osmocom programs have a common logging mechanism, configurable by the config files as well as the telnet VTY. 

 h2. System Logging 

 Depending on the system's logging configuration, logs may by default be visible in /var/log/daemon.log, or by using journalctl: 

 <pre> 
 journalctl -f -u osmo-hlr 
 </pre> 

 When journalctl is used, it may be necessary to enable it first, e.g. by setting "Storage=volatile" in /etc/systemd/journald.conf followed by a 'systemctl restart systemd-journald'; you may also need to 'systemctl unmask systemd-journald.service systemd-jounald.socket'. Logging will only start appearing for components that were restarted after these changes. 

 h2. telnet VTY logging 

 A sure way to see the logs is to connect to the program's telnet VTY and enable logging on the VTY session -- this way you do not modify the application's default logging, but create a separate logging target for your telnet VTY session: 

 <pre> 
 $ telnet localhost 4254 
 OsmoMSC> logging enable  
 OsmoMSC> logging level ? 
   all        Global setting for all subsystems 
   rll        A-bis Radio Link Layer (RLL) 
   cc         Layer3 Call Control (CC) 
   mm         Layer3 Mobility Management (MM) 
   [...] 
 OsmoMSC> logging level all ? 
 everything debug        info         notice       error        fatal       
 OsmoMSC> logging level all debug  
 OsmoMSC> logging filter all 1 
 </pre> 

 You will see logging output on your telnet console immediately. Note that the VTY prompt is still listening, so you may at any time issue 'logging filter all 0' to switch off logging, and be able to type commands without being cluttered by ongoing log output. 

 h2. stderr logging 

 A common configuration you can add to any of the above configuration files to show *all* logging on stderr is: 

 <pre> 
 log stderr 
  logging filter all 1 
  logging color 1 
  logging print category 1 
  logging timestamp 1 
  logging print extended-timestamp 1 
  logging level all debug 
 </pre> 

 The @filter all 1@ switches on logging, read "do not discard all logging". The amount of logging seen is determined by @logging level ...@ commands, here all categories are set to level @debug@, to show absolutely all logging. You will probably want to refine that. 

 h1. Point Codes 

 If you'd like to configure non-default point-codes, see this example for OsmoHNBGW on the general approach: 

 <pre> 
 cs7 instance 0 
  # HNBGW's local point code 
  point-code 0.23.5 
  # Address book entries, used below 
  sccp-address my_msc 
   point-code 0.23.1 
  sccp-address my_sgsn 
   point-code 0.23.4 
 hnbgw 
  iucs 
   remote-addr my_msc 
  iups 
   remote-addr my_sgsn 
 </pre> 

 h1. Troubleshooting 

 h2. APN for Data Service 

 For the data service to work, phones generally need an APN added to their 
 configuration, or they will not even attempt to establish a data connection. 
 The APN should match the name configured in osmo-ggsn.conf. 

 The APN configuration steps are usually similar to: 

 * Navigate to APN settings: 
 ** 'Settings' 
 ** 'Wireless & Networks' 
 ** 'Mobile networks' 
 ** 'Access Point Names' 
 * You should see the list of APNs (possibly empty) 
 * Press the Menu button 
 * Choose 'New APN' 
 * Enter values for 'Name' as well as 'APN' 
 * Again press the Menu button 
 * Choose 'Save' 
 * The APN should now appear in the list of APNs. 
 * Possibly tap the bullet icon to select the APN as default.
Add picture from clipboard (Maximum size: 48.8 MB)