Code-audit » History » Version 57
gnutoo, 02/19/2016 10:49 PM
1 | 57 | gnutoo | |
---|---|---|---|
2 | h2. Introduction |
||
3 | |||
4 | 1 | gnutoo | This page is a code audit that: |
5 | 57 | gnutoo | * Verify if the license are correct(not copied from osmocom-bb and changed from GPL to BSD) |
6 | * permit to view the license of each file, that's important for the inclusion into the official nuttx that only accepts BSD code for the non-applications part. |
||
7 | |||
8 | h2. Audit |
||
9 | |||
10 | 1 | gnutoo | Currently the following files were added or modified by nuttx-bb(on top of nuttx): |
11 | 57 | gnutoo | <pre> |
12 | 1 | gnutoo | apps/examples/calypsotest/Makefile |
13 | apps/examples/calypsotest/bounce_analyze.c |
||
14 | apps/examples/calypsotest/main.c |
||
15 | 22 | gnutoo | apps/examples/ostest/main.c |
16 | 30 | gnutoo | nuttx/arch/arm/include/calypso/armio.h OK,BSD only definitions of functions |
17 | 26 | gnutoo | nuttx/arch/arm/include/calypso/clock.h no license, copied from omsocombb's src/target/firmware/include/clock.h(which has no license too) |
18 | nuttx/arch/arm/include/calypso/debug.h no license, copied from omsocombb's src/target/firmware/include/debug.h(which has no license too), debug macros |
||
19 | 57 | gnutoo | nuttx/arch/arm/include/calypso/defines.h no license, copied from osmocombb's src/target/firmware/include/defines.h(which has no license too), trivial defines like #define +unused attribute+((unused)) |
20 | 26 | gnutoo | nuttx/arch/arm/include/calypso/irq.h GPL, copyright Harald Welte and Stefan Richter |
21 | 57 | gnutoo | nuttx/arch/arm/include/calypso/memory.h no license,copied from osmocombb's src/target/firmware/include/memory.h(which has no license too), trivial defines like #define readb(a) +arch_getb(a) |
22 | 19 | gnutoo | nuttx/arch/arm/include/calypso/timer.h no license, copied from osmocombb's src/target/firmware/include/timer.h(which has no license too), only definitions of functions |
23 | nuttx/arch/arm/src/Makefile OK,BSD |
||
24 | 17 | gnutoo | nuttx/arch/arm/src/calypso/Make.defs OK,BSD |
25 | 29 | gnutoo | nuttx/arch/arm/src/calypso/calypso_armio.c BSD,copyright Stefan Richter, seem ok(grep found nothing in osmocom-bb) |
26 | 17 | gnutoo | nuttx/arch/arm/src/calypso/calypso_head.S no license, specific to nuttx( it jumps to functions like up_ which are nuttx functions) |
27 | 32 | gnutoo | nuttx/arch/arm/src/calypso/calypso_heap.c problematic?, see below |
28 | 13 | gnutoo | nuttx/arch/arm/src/calypso/calypso_irq.c OK,GPL, copied from osmocombb's src/target/firmware/calypso/irq.c , copyright Harald Welte and Stefan Richter |
29 | 15 | gnutoo | nuttx/arch/arm/src/calypso/calypso_keypad.c OK,BSD, totally different from osmocom-bb's src/target/firmware/calypso/keypad.c |
30 | 18 | gnutoo | nuttx/arch/arm/src/calypso/calypso_lowputc.S OK,BSD, not found in osmocom-bb source |
31 | 1 | gnutoo | nuttx/arch/arm/src/calypso/calypso_serial.c OK,BSD, based on nuttx/arch/arm/src/c5471/c5471_serial.c from nuttx (verified with diff) |
32 | 14 | gnutoo | nuttx/arch/arm/src/calypso/calypso_spi.c OK,BSD, wrapper arround osmocombb's SPI, incomplete |
33 | 21 | gnutoo | nuttx/arch/arm/src/calypso/calypso_timer.c OK,GPL, copyright Harald Welte and Stefan Richter |
34 | 14 | gnutoo | nuttx/arch/arm/src/calypso/chip.h OK,BSD,based on nuttx/arch/arm/src/c5471/chip.h |
35 | 20 | gnutoo | nuttx/arch/arm/src/calypso/clock.c OK,GPL, copyright Harald Welte |
36 | 3 | gnutoo | nuttx/arch/arm/src/common/up_internal.h OK,BSD,trivial modification(part of nuttx) |
37 | nuttx/configs/compal_e88/calypsotest/Make.defs OK,BSD |
||
38 | nuttx/configs/compal_e88/calypsotest/appconfig OK,BSD |
||
39 | nuttx/configs/compal_e88/calypsotest/defconfig OK,BSD |
||
40 | nuttx/configs/compal_e88/calypsotest/setenv.sh OK,BSD |
||
41 | nuttx/configs/compal_e88/include/board.h OK,BSD |
||
42 | nuttx/configs/compal_e88/ld.script OK,BSD |
||
43 | nuttx/configs/compal_e88/nsh/Make.defs OK,BSD |
||
44 | nuttx/configs/compal_e88/nsh/appconfig OK,BSD |
||
45 | nuttx/configs/compal_e88/nsh/defconfig OK,BSD |
||
46 | nuttx/configs/compal_e88/nsh/ld.script OK,BSD |
||
47 | nuttx/configs/compal_e88/nsh/setenv.sh OK,BSD |
||
48 | nuttx/configs/compal_e88/ostest/Make.defs OK,BSD |
||
49 | nuttx/configs/compal_e88/ostest/appconfig OK,BSD |
||
50 | nuttx/configs/compal_e88/ostest/defconfig OK,BSD |
||
51 | nuttx/configs/compal_e88/ostest/setenv.sh OK,BSD |
||
52 | nuttx/configs/compal_e88/src/Make.dep OK,BSD |
||
53 | nuttx/configs/compal_e88/src/Makefile OK,BSD |
||
54 | nuttx/configs/compal_e88/src/dummy.c OK,BSD |
||
55 | nuttx/configs/compal_e99/calypsotest/Make.defs OK,BSD |
||
56 | nuttx/configs/compal_e99/calypsotest/appconfig OK,BSD |
||
57 | nuttx/configs/compal_e99/calypsotest/defconfig OK,BSD |
||
58 | nuttx/configs/compal_e99/calypsotest/setenv.sh OK,BSD |
||
59 | nuttx/configs/compal_e99/include/board.h OK,BSD |
||
60 | nuttx/configs/compal_e99/ld.script OK,BSD |
||
61 | nuttx/configs/compal_e99/nsh/Make.defs OK,BSD |
||
62 | nuttx/configs/compal_e99/nsh/appconfig OK,BSD |
||
63 | nuttx/configs/compal_e99/nsh/defconfig OK,BSD |
||
64 | nuttx/configs/compal_e99/nsh/ld.script OK,BSD |
||
65 | nuttx/configs/compal_e99/nsh/setenv.sh OK,BSD |
||
66 | nuttx/configs/compal_e99/ostest/Make.defs OK,BSD |
||
67 | nuttx/configs/compal_e99/ostest/appconfig OK,BSD |
||
68 | nuttx/configs/compal_e99/ostest/defconfig OK,BSD |
||
69 | nuttx/configs/compal_e99/ostest/setenv.sh OK,BSD |
||
70 | nuttx/configs/compal_e99/src/Makefile OK,BSD |
||
71 | 9 | gnutoo | nuttx/configs/compal_e99/src/dummy.c OK,BSD |
72 | 12 | gnutoo | nuttx/drivers/Makefile OK,BSD |
73 | 5 | gnutoo | nuttx/drivers/sercomm/Make.defs OK,BSD |
74 | 1 | gnutoo | nuttx/drivers/sercomm/console.c mostly OK(see below), BSD |
75 | nuttx/drivers/sercomm/loadwriter.py no copyright at all, small enough |
||
76 | nuttx/drivers/sercomm/uart.c OK,GPL, copyright Harald Welte and Ingo Albrecht |
||
77 | nuttx/drivers/sercomm/uart.h no license, copied from osmocom-bb's src/target/firmware/include/uart.h which had no license too |
||
78 | nuttx/include/nuttx/spi.h OK,BSD, only small change made |
||
79 | nuttx/include/sercomm/msgb.h OK,GPL,copyright Harald Welte |
||
80 | nuttx/include/sercomm/sercomm.h copy of src/target/firmware/include/comm/sercomm.h, no license in both. |
||
81 | nuttx/include/sercomm/sercomm_cons.h no license,copied from osmocom-bb's src/target/firmware/include/comm/sercomm_cons.h which had no license, interface only(only 2 definitions of functions inside) |
||
82 | 70 files changed, 9221 insertions(+), 3 deletions(-) |
||
83 | 57 | gnutoo | </pre> |
84 | 1 | gnutoo | |
85 | We can safely assume that the config dir weren't took from osmocom-bb. |
||
86 | 57 | gnutoo | |
87 | h2. init.c and console.c == |
||
88 | nuttx-bb === |
||
89 | * Copyright Stefan Richter |
||
90 | * BSD License |
||
91 | * nuttx/drivers/sercomm/console.c |
||
92 | <pre> |
||
93 | 1 | gnutoo | /* XXX: initialize MODEMUART to be used for sercomm*/ |
94 | 10 | gnutoo | uart_init(SERCOMM_UART_NR, 1); |
95 | uart_baudrate(SERCOMM_UART_NR, UART_115200); |
||
96 | 57 | gnutoo | </pre> |
97 | |||
98 | h3. osmocom-bb |
||
99 | |||
100 | * GPL |
||
101 | * Copyright Harald Welte and Steve Markgraf |
||
102 | * src/target/firmware/board/compal_e99/init.c |
||
103 | <pre> |
||
104 | 33 | gnutoo | /* initialize MODEM UART to be used for sercomm*/ |
105 | uart_init(SERCOMM_UART_NR, 1); |
||
106 | uart_baudrate(SERCOMM_UART_NR, UART_115200); |
||
107 | 57 | gnutoo | </pre> |
108 | 1 | gnutoo | |
109 | |||
110 | 57 | gnutoo | h2. calypsotest/bounce_analyze.c == |
111 | nuttx-bb === |
||
112 | * Copyright Stefan Richter |
||
113 | * GPL License (could keep as GPL since it is an application) |
||
114 | * apps/examples/calypsotest/bounce_analyze.c |
||
115 | 1 | gnutoo | |
116 | 57 | gnutoo | h3. osmocom-bb |
117 | |||
118 | * nothing found |
||
119 | |||
120 | |||
121 | |||
122 | h2. calypsotest/main.c == |
||
123 | nuttx-bb === |
||
124 | * Copyright Stefan Richter |
||
125 | * BSD License |
||
126 | * apps/examples/calypsotest/main.c |
||
127 | <pre> |
||
128 | 40 | gnutoo | static void lights_on(void) |
129 | { |
||
130 | uint16_t reg; |
||
131 | |||
132 | 1 | gnutoo | reg = readw(ASIC_CONF_REG); |
133 | /* LCD Set I/O(3) / SA0 to I/O(3) mode */ |
||
134 | reg &= ~( (1 << 12) | (1 << 10) | (1 << 7) | (1 << 1)) ; |
||
135 | /* don't set function pins to I2C Mode, C155 uses UWire */ |
||
136 | /* TWL3025: Set SPI+RIF RX clock to rising edge */ |
||
137 | reg |= (1 << 13) | (1 << 14); |
||
138 | writew(reg, ASIC_CONF_REG); |
||
139 | |||
140 | /* LCD Set I/O(3) to output mode and enable C155 backlight (IO1) */ |
||
141 | /* FIXME: Put the display backlight control to backlight.c */ |
||
142 | reg = readw(IO_CNTL_REG); |
||
143 | reg &= ~( (1 << 3) | (1 << 1)); |
||
144 | writew(reg, IO_CNTL_REG); |
||
145 | |||
146 | /* LCD Set I/O(3) output low */ |
||
147 | reg = readw(ARMIO_LATCH_OUT); |
||
148 | reg &= ~(1 << 3); |
||
149 | reg |= (1 << 1); |
||
150 | writew(reg, ARMIO_LATCH_OUT); |
||
151 | } |
||
152 | 57 | gnutoo | </pre> |
153 | |||
154 | h3. osmocom-bb |
||
155 | |||
156 | * Copyright Harald Welte and Steve Markgraf |
||
157 | * GPL License |
||
158 | * src/target/firmware/board/compal_e99/init.c |
||
159 | <pre> |
||
160 | 40 | gnutoo | static void board_io_init(void) |
161 | { |
||
162 | uint16_t reg; |
||
163 | |||
164 | reg = readw(ASIC_CONF_REG); |
||
165 | /* LCD Set I/O(3) / SA0 to I/O(3) mode */ |
||
166 | reg &= ~( (1 << 12) | (1 << 10) | (1 << 7) | (1 << 1)) ; |
||
167 | /* don't set function pins to I2C Mode, C155 uses UWire */ |
||
168 | 1 | gnutoo | /* TWL3025: Set SPI+RIF RX clock to rising edge */ |
169 | reg |= (1 << 13) | (1 << 14); |
||
170 | writew(reg, ASIC_CONF_REG); |
||
171 | |||
172 | /* LCD Set I/O(3) to output mode and enable C155 backlight (IO1) */ |
||
173 | /* FIXME: Put the display backlight control to backlight.c */ |
||
174 | reg = readw(IO_CNTL_REG); |
||
175 | reg &= ~( (1 << 3) | (1 << 1)); |
||
176 | 38 | gnutoo | writew(reg, IO_CNTL_REG); |
177 | |||
178 | 1 | gnutoo | /* LCD Set I/O(3) output low */ |
179 | reg = readw(ARMIO_LATCH_OUT); |
||
180 | reg &= ~(1 << 3); |
||
181 | reg |= (1 << 1); |
||
182 | writew(reg, ARMIO_LATCH_OUT); |
||
183 | } |
||
184 | 57 | gnutoo | </pre> |
185 | 1 | gnutoo | |
186 | 57 | gnutoo | h2. ostest/main.c == |
187 | nuttx-bb === |
||
188 | * Copyright Gregory Nutt |
||
189 | * BSD License |
||
190 | * apps/examples/ostest/main.c |
||
191 | * Note: lights_on function used snippet code of [[OsmocomBB]] src/target/firmware/board/compal_e99/init.c |
||
192 | 1 | gnutoo | |
193 | 57 | gnutoo | h3. osmocom-bb |
194 | 1 | gnutoo | |
195 | 57 | gnutoo | * nothing found |
196 | |||
197 | |||
198 | h2. calypso/calypso_armio.c == |
||
199 | nuttx-bb === |
||
200 | * Copyright Stefan Richter |
||
201 | * BSD License |
||
202 | * nuttx/arch/arm/src/calypso/calypso_armio.c |
||
203 | |||
204 | h3. osmocom-bb |
||
205 | |||
206 | * nothing found |
||
207 | |||
208 | |||
209 | h2. calypso/calypso_head.S == |
||
210 | nuttx-bb === |
||
211 | * No copyright |
||
212 | * No License |
||
213 | * nuttx/arch/arm/src/calypso/calypso_head.S |
||
214 | * Note: this is same file as nuttx/arch/arm/src/chip/calypso_head.S |
||
215 | |||
216 | h3. osmocom-bb |
||
217 | |||
218 | * nothing found |
||
219 | |||
220 | |||
221 | h2. calypso/calypso_irq.c == |
||
222 | nuttx-bb === |
||
223 | * Copyright Harald Welte and Stefan Richter |
||
224 | * GPL License (need change to BSD) |
||
225 | * nuttx/arch/arm/src/calypso/calypso_irq.c |
||
226 | <pre> |
||
227 | 1 | gnutoo | static void _irq_enable(enum irq_nr nr, int enable) |
228 | 42 | gnutoo | { |
229 | uint16_t *reg = IRQ_REG(MASK_IT_REG1); |
||
230 | uint16_t val; |
||
231 | |||
232 | if (nr > 15) { |
||
233 | reg = IRQ_REG(MASK_IT_REG2); |
||
234 | nr -= 16; |
||
235 | } |
||
236 | |||
237 | val = readw(reg); |
||
238 | if (enable) |
||
239 | 43 | gnutoo | val &= ~(1 << nr); |
240 | else |
||
241 | val |= (1 << nr); |
||
242 | writew(val, reg); |
||
243 | } |
||
244 | 57 | gnutoo | </pre> |
245 | |||
246 | h3. osmocom-bb |
||
247 | |||
248 | * Copyright Harald Welte |
||
249 | * GPL License |
||
250 | * src/target/firmware/calypso/irq.c |
||
251 | <pre> |
||
252 | 1 | gnutoo | static void _irq_enable(enum irq_nr nr, int enable) |
253 | { |
||
254 | uint16_t *reg = IRQ_REG(MASK_IT_REG1); |
||
255 | uint16_t val; |
||
256 | |||
257 | 43 | gnutoo | if (nr > 15) { |
258 | 1 | gnutoo | reg = IRQ_REG(MASK_IT_REG2); |
259 | nr -= 16; |
||
260 | } |
||
261 | |||
262 | 43 | gnutoo | val = readw(reg); |
263 | if (enable) |
||
264 | 44 | gnutoo | val &= ~(1 << nr); |
265 | else |
||
266 | val |= (1 << nr); |
||
267 | writew(val, reg); |
||
268 | } |
||
269 | 57 | gnutoo | </pre> |
270 | 44 | gnutoo | |
271 | |||
272 | 57 | gnutoo | h2. calypso_keypad.c == |
273 | nuttx-bb === |
||
274 | * Copyright Stefan Richter |
||
275 | * BSD License |
||
276 | * nuttx/arch/arm/src/calypso/calypso_keypad.c |
||
277 | 1 | gnutoo | |
278 | 57 | gnutoo | h3. osmocom-bb |
279 | |||
280 | * nothing found |
||
281 | |||
282 | |||
283 | h2. calypso_timer.c == |
||
284 | nuttx-bb === |
||
285 | * Copyright Harald Welte and Stefan Richter |
||
286 | * GPL License (need change to BSD) |
||
287 | * nuttx/arch/arm/src/calypso/calypso_timer.c |
||
288 | * Note: verbatim copy from [[OsmocomBB]] calypso/timer.c |
||
289 | |||
290 | h3. osmocom-bb |
||
291 | |||
292 | * Copyright Harald Welte |
||
293 | * GPL License |
||
294 | * src/target/firmware/calypso/timer.c |
||
295 | |||
296 | |||
297 | h2. init.c and calypso_heap.c == |
||
298 | nuttx-bb === |
||
299 | * Copyright Stefan Richter |
||
300 | * BSD License |
||
301 | * nuttx/arch/arm/src/calypso/calypso_heap.c |
||
302 | <pre> |
||
303 | 1 | gnutoo | void up_addregion(void) |
304 | { |
||
305 | #ifdef CONFIG_ARCH_BOARD_COMPALE99 |
||
306 | 10 | gnutoo | /* Disable watchdog in first non-common function */ |
307 | 1 | gnutoo | wdog_enable(0); |
308 | #endif |
||
309 | // XXX: change to initialization of extern memory with save defaults |
||
310 | /* Configure memory interface */ |
||
311 | calypso_mem_cfg(CALYPSO_nCS0, 3, CALYPSO_MEM_16bit, 1); |
||
312 | calypso_mem_cfg(CALYPSO_nCS1, 3, CALYPSO_MEM_16bit, 1); |
||
313 | calypso_mem_cfg(CALYPSO_nCS2, 5, CALYPSO_MEM_16bit, 1); |
||
314 | calypso_mem_cfg(CALYPSO_nCS3, 5, CALYPSO_MEM_16bit, 1); |
||
315 | calypso_mem_cfg(CALYPSO_CS4, 0, CALYPSO_MEM_8bit, 1); |
||
316 | calypso_mem_cfg(CALYPSO_nCS6, 0, CALYPSO_MEM_32bit, 1); |
||
317 | calypso_mem_cfg(CALYPSO_nCS7, 0, CALYPSO_MEM_32bit, 0); |
||
318 | |||
319 | /* Set VTCXO_DIV2 = 1, configure PLL for 104 MHz and give ARM half of that */ |
||
320 | calypso_clock_set(2, CALYPSO_PLL13_104_MHZ, ARM_MCLK_DIV_2); |
||
321 | |||
322 | /* Configure the RHEA bridge with some sane default values */ |
||
323 | calypso_rhea_cfg(0, 0, 0xff, 0, 1, 0, 0); |
||
324 | } |
||
325 | |||
326 | 57 | gnutoo | </pre> |
327 | |||
328 | h3. Osmocom-bb |
||
329 | |||
330 | * GPL |
||
331 | * Copyright Harald Welte and Steve Markgraf |
||
332 | * src/target/firmware/board/compal_e99/init.c |
||
333 | <pre> |
||
334 | 47 | gnutoo | void board_init(void) |
335 | { |
||
336 | /* Disable watchdog (compal loader leaves it enabled) */ |
||
337 | wdog_enable(0); |
||
338 | |||
339 | /* Configure memory interface */ |
||
340 | calypso_mem_cfg(CALYPSO_nCS0, 3, CALYPSO_MEM_16bit, 1); |
||
341 | calypso_mem_cfg(CALYPSO_nCS1, 3, CALYPSO_MEM_16bit, 1); |
||
342 | calypso_mem_cfg(CALYPSO_nCS2, 5, CALYPSO_MEM_16bit, 1); |
||
343 | calypso_mem_cfg(CALYPSO_nCS3, 5, CALYPSO_MEM_16bit, 1); |
||
344 | calypso_mem_cfg(CALYPSO_CS4, 0, CALYPSO_MEM_8bit, 1); |
||
345 | calypso_mem_cfg(CALYPSO_nCS6, 0, CALYPSO_MEM_32bit, 1); |
||
346 | 45 | gnutoo | calypso_mem_cfg(CALYPSO_nCS7, 0, CALYPSO_MEM_32bit, 0); |
347 | |||
348 | 55 | gnutoo | /* Set VTCXO_DIV2 = 1, configure PLL for 104 MHz and give ARM half of that */ |
349 | calypso_clock_set(2, CALYPSO_PLL13_104_MHZ, ARM_MCLK_DIV_2); |
||
350 | |||
351 | 56 | gnutoo | /* Configure the RHEA bridge with some sane default values */ |
352 | calypso_rhea_cfg(0, 0, 0xff, 0, 1, 0, 0); |
||
353 | |||
354 | 57 | gnutoo | </pre> |
355 | |||
356 | h2. Relicensing permissions |
||
357 | |||
358 | * "Harald Welte":http://lists.osmocom.org/pipermail/baseband-devel/2012-February/002813.html |
||
359 | * Ingo Albrecht: |
||
360 | 48 | gnutoo | By private mail |
361 | 57 | gnutoo | <pre> |
362 | 48 | gnutoo | I am open to relicensing and other such agreements. |
363 | 57 | gnutoo | </pre> |
364 | * Stefan Richter: |
||
365 | 48 | gnutoo | By private mail |
366 | 57 | gnutoo | <pre> |
367 | 48 | gnutoo | Sure, go ahead. I don't mind which license but we agreed (I think) to |
368 | use the nuttx one. Mostly such that we can submit to upstream some day |
||
369 | 54 | gnutoo | if desired. |
370 | 57 | gnutoo | </pre> |
371 | * Denis Carikli |
||
372 | * Alan Carvalho de Assis |
||
373 | * "Sylvain Munaut":http://lists.osmocom.org/pipermail/baseband-devel/2012-May/002967.html: |
||
374 | ** src/target/firmware/calypso/uwire.c has permission |
||
375 | ** "anything close to the GSM function (dsp / tsp / l1 / ....)." does *not* have permission |
||
376 | * Steve Markgraf |
||
377 | 54 | gnutoo | On the #osmocom channel on Freenode IRC server: |
378 | 57 | gnutoo | <pre> |
379 | 51 | gnutoo | May 13 21:55:40 <GNUtoo-desktop> hi steve|m, we need permission for relicensing the commit a13a4fda926aa272e55964c8f86cb31fb4065995 (uwire: add a chip-select for CS0, needed by the J100i display) for inclusion in nuttx(BSD licensed). |
380 | May 13 22:00:03 <steve|m> I don't mind such trivial changes being relicensed, but I second what tnt stated on the ml, for the actual GSM parts of the code that's different |
||
381 | 57 | gnutoo | </pre> |
382 | 51 | gnutoo | |
383 | 57 | gnutoo | |
384 | h2. Listing authors by file |
||
385 | |||
386 | <pre> |
||
387 | 1 | gnutoo | src/target/firmware/calypso/irq.c: |
388 | Author: Harald Welte <laforge@gnumonks.org> |
||
389 | |||
390 | src/target/firmware/calypso/timer.c: |
||
391 | Author: Harald Welte <laforge@gnumonks.org> |
||
392 | Author: Ingo Albrecht <prom@berlin.ccc.de> |
||
393 | |||
394 | src/target/firmware/calypso/clock.c: |
||
395 | Author: Harald Welte <laforge@gnumonks.org> |
||
396 | Author: Ingo Albrecht <prom@berlin.ccc.de> (very small modifications) |
||
397 | Author: Steve Markgraf <steve@steve-m.de> (very small modifications) |
||
398 | |||
399 | src/target/firmware/calypso/uart.c: |
||
400 | Author: Alex Badea <vamposdecampos@gmail.com> (very small modifications) |
||
401 | Author: Christian Vogel <vogelchr@vogel.cx> |
||
402 | Author: Harald Welte <laforge@gnumonks.org> |
||
403 | Author: Ingo Albrecht <prom@berlin.ccc.de> |
||
404 | Author: Wolfram Sang <wolfram@the-dreams.de> (very small modifications) |
||
405 | |||
406 | src/target/firmware/board/compal_e99/init.c: |
||
407 | Author: Harald Welte <laforge@gnumonks.org> |
||
408 | Author: Ingo Albrecht <prom@berlin.ccc.de> (small modifications) |
||
409 | Author: Steve Markgraf <steve@steve-m.de> |
||
410 | Author: Wolfram Sang <wolfram@the-dreams.de> (very small modifications) |
||
411 | |||
412 | 57 | gnutoo | </pre> |