BS11LMT » History » Version 7
laforge, 02/19/2016 10:48 PM
Name changed from BS11_LMT to BS11/LMT
| 1 | 1 | laforge | |
|---|---|---|---|
| 2 | |||
| 3 | 7 | laforge | h2. How to use LMT |
| 4 | 1 | laforge | |
| 5 | |||
| 6 | 7 | laforge | * connect serial port of PC with J2 on BS11 using the cable that came with the BS11 |
| 7 | * start LMT program |
||
| 8 | |||
| 9 | |||
| 10 | h3. LMT rs232 connector pinout |
||
| 11 | |||
| 12 | |||
| 13 | 2 | laforge | If you look at the BS-11 interface (Antenne connectors top), its the upper 8-pin connector: |
| 14 | |||
| 15 | 7 | laforge | <pre> |
| 16 | 1 | laforge | The four E1 BNC connectors are above here. |
| 17 | 2 | laforge | |
| 18 | (Rx) x x x x (right pin: Gnd) |
||
| 19 | 1 | laforge | (Tx) x x x x (right pin: +5V) |
| 20 | 2 | laforge | | |
| 21 | + LMT |
||
| 22 | 7 | laforge | </pre> |
| 23 | 2 | laforge | |
| 24 | 5 | laforge | see also [[Image(BS11_Configuration:bs11_power_lmt_cabling.jpg)]] |
| 25 | 2 | laforge | |
| 26 | 7 | laforge | *J2:* |
| 27 | 3 | laforge | |
| 28 | [[Image(img_6412-1.jpg, 15%)]] |
||
| 29 | 4 | zecke | |
| 30 | 7 | laforge | <pre> |
| 31 | 3 | laforge | 5(GND) |
| 32 | 1 | laforge | | |
| 33 | 3 | laforge | | 3(TX) |
| 34 | | | |
||
| 35 | 1 | laforge | X 0 X 0 |
| 36 | 3 | laforge | 0 0 X 0 |
| 37 | | |
||
| 38 | 4 | zecke | 2(RX) |
| 39 | 7 | laforge | </pre> |
| 40 | 3 | laforge | |
| 41 | |||
| 42 | 7 | laforge | *RS232:* |
| 43 | 1 | laforge | |
| 44 | [[Image(img_6414-1.jpg, 15%)]] |
||
| 45 | |||
| 46 | 7 | laforge | <pre> |
| 47 | 1 | laforge | 5(GND) |
| 48 | | |
||
| 49 | | 3(TX) |
||
| 50 | | | |
||
| 51 | | | 2(RX) |
||
| 52 | 4 | zecke | | | | |
| 53 | 3 | laforge | X 0 X X 0 |
| 54 | 4 | zecke | 0 0 0 0 |
| 55 | 7 | laforge | </pre> |
| 56 | 4 | zecke | |
| 57 | 3 | laforge | |
| 58 | 7 | laforge | h2. Known Versions (and issues?) |
| 59 | 3 | laforge | |
| 60 | 7 | laforge | |
| 61 | |||
| 62 | h3. LMT v4.17 |
||
| 63 | |||
| 64 | |||
| 65 | |||
| 66 | h3. LMT v4.21 |
