Activity
From 06/03/2011 to 07/02/2011
07/02/2011
- 05:08 PM Feature #1442 (Closed): Make LED footprints 0805 instead of 0603
- done for v1.1 in git 024bdaddddc84b7384fe138ec34b836c623f5588
- 11:57 AM Feature #1442: Make LED footprints 0805 instead of 0603
- done in v1.0
git 3a4ea6bf430dba07a7c275d402113f2215b415b5
will do in v1.1 - 12:00 PM Feature #1440 (Closed): Use through-hole mini-USB-B socket
- done in v1.1
added in git 945909a241c88614088e93f6410c0948cee27c8b
will not be done in v1.0_production because un... - 11:58 AM Feature #1441 (Closed): Use through-hole 2.5mm jack
- done for v1.1
added in git 945909a241c88614088e93f6410c0948cee27c8b
will not be done for v1.0 because untested yet - 11:56 AM Feature #1443 (Closed): Adapt to different SPI flash (foot print)
- done in v1.0_production
added in git 8872e080df95fd734c4ed56decaf310e1a28b816
routed in git dcf3d0aaedb2994e968dea6... - 11:55 AM Feature #1444 (Closed): Adapt to different shottky diode footprint
- done in v1.0_production branch
added in git 8872e080df95fd734c4ed56decaf310e1a28b816
routed in git dcf3d0aaedb2994e... - 11:53 AM Feature #1439 (Closed): move ERASE and TEST jumper a tint bit, so a 1x4pin header works
- done in v1.0_production and v1.1
- 11:53 AM Feature #1438 (Closed): add ID-1 slot to SIMtrace
- added for v1.1
added and routed in git 0a35394773e8f1d4f3eba2994fca8b8b735c1344 - 11:51 AM Feature #1445 (Closed): Some component labels (resistors/capacitors) are not readable
- corrected in v1.0 _production branch
v1.1 is a complete rework - 11:33 AM Bug #1446 (Closed): test ticket to check notification
06/21/2011
- 09:21 AM Bug #1437: on resistance of bus switch not acceptable, at least not for Vcc
- the bus switch has been changed : a type CB3Q (CB3Q3244) it now used instead of the QS3244.
It has a Ron of ~5 Ohms ... - 09:13 AM Bug #1434: socket for FPC SIM adapter is mechanically incompatible with rebelsim fpc
- I putted the SWT3R in the BOM, which had cable locks (I did not read the datasheet to the end).
The SFW1R is the rig... - 09:09 AM Feature #1428: increase default trace width in simtrace pcb
- not all the VCC traces can be thicker, because of the chip pad dimension and clearance.
But most VCC tracks are now ... - 09:07 AM Feature #1429: usb jack type is really hard to manually solder
- I bought the cheapest one without checking the soldering easiness.
Now the Hirose UX60-MB-5ST is used (compatible wi...
06/19/2011
- 01:11 PM Feature #1436: add VCC_PHONE to an unused GPIO
- done in PC v0.9.8 (pin 27)
- 12:25 PM Feature #1433: use 90 degree angled jumpers for ERASE and TEST
- done on PCB v0.9.7
- 12:24 PM Bug #1435: sim card detect does not work (SW_SIM)
- fixed in PCN v0.9.7
- 09:02 AM Bug #1424: simtrace pinout of tps73633 is wrong
- correct in [[KiCAD]] v0.9.3, PCB v0.9.6
- 08:47 AM Bug #1432: simtrace: bootloader switch without function
- fixed in [[KiCAD]].
gerber will be rendered with v1.0
06/17/2011
- 09:08 AM Feature #1430: clearly indicate location of 'pin 1' of components and connectors
- pin 1 marker placed in PCB v0.9.6
- 09:07 AM Bug #1426: simtrace component names on silk screen unreadable
- component names moved.
correct in [[KiCAD]] PCB v0.9.6 - 08:36 AM Bug #1431: use PA16 for UDP_PUP as required by SAM-BA
- I wasn't aware of this constraint.
Now fixed in [[KiCAD]] (rerouting has also been done). gerber will be rendered wi... - 08:33 AM Bug #1427: simtrace BC847 footprint has B / E switched
- [[KiCAD]] SOT23 pin numbering did not matches and I haven't see it.
Now corrected in [[KiCAD]]. gerber will be rende... - 08:32 AM Bug #1425: simtrace pinout of bootloader / reset switch is wrong
- I remembered the circuit diagram wrong when setting the pin numbers.
Now corrected in [[KiCAD]]. gerber will be rend... - 08:27 AM Bug #1424: simtrace pinout of tps73633 is wrong
- Only the TAB was not connected to GND, but was internally connected to the other ground pin. Now ground is connected ...
Also available in: Atom
