FakeTRX (Virtual Um-interface)¶
FakeTRX is a virtual Um-interface implementation written in Python, which allows you to connect OsmocomBB and OsmoBTS without actual RF hardware. The main purpose of this software is to facilitate and simplify the development and testing process. In other words, you don't need to physically run your GSM network nor use any kind of special hardware - just run a few scripts and do anything you want / need in your virtual GSM network!
The main difference is that FakeTRX actually works on GSM L1, while VIRT-PHY works on higher levels, using GSMTAP and multicast sockets to exchange the data. It means that FakeTRX provides the TRX Interface for both OsmocomBB and OsmoBTS, and forwards GSM bursts between both sides. So, no need to do any modifications in the OsmoBTS source code, just use osmo-bts-trx.
Of course, Python is slower than C, for example. But it's more than enough for exchanging UDP messages between OsmocomBB and OsmoBTS, and vice versa. Moreover, it can be easily reimplemented in C, if someone interested in better performance.
What about RSSI and ToA (Timing of Arrival)?¶
Since we are talking about the virtual interface, it's possible to emulate any values for both RSSI and ToA.
Can I run multiple BTS and / or multiple MS instances?¶
Since OsmocomBB was extended with TRX Interface support, follow the corresponding instructions and compile OsmocomBB with trxcon application. After that, you may find the FakeTRX toolkit located in 'src/target/trx_toolkit/'. See README for more details.
Tip: feel free to use tmux or screen to avoid a mess with multiple windows
1. Run the network side stack you have. In this example we will use the Network in the Box:
$ osmo-nitb -c ./openbsc.cfg -l ./hlr.sqlite3 -P -C --debug=DRLL:DCC:DMM:DRR:DRSL:DNM
2. Run the fake transceiver:
$ cd osmocom-bb/src/target/trx_toolkit/ $ python ./fake_trx.py
$ osmo-bts-trx -c ./osmo-bts.cfg
Congratulations! Now you have a virtual GSM network running. As you can see, the virtual transceiver emulates the clock source, as this is required for OsmoBTS. Also, it handles only a few important commands, such as RXTUNE and TXTUNE, but ignores other irrelevant ones.
$ cd osmocom-bb/src/host/trxcon/ $ ./trxcon
5. Finally, run any L2&3 application, e.g. ccch_scan:
$ cd osmocom-bb/src/host/layer23/src/misc/ $ ./ccch_scan -a ARFCN -i 127.0.0.1
Please note that ARFCN value should match the one your BTS configured to.
Since this step, you should see the broadcast messages coming from the virtual network, like in case of a real one. You can use Wireshark to analyze them.
As you should already know, mobile applications implements a simple mobile phone with SMS, USSD and voice calls. In the virtual network we can benefit from using a virtual SIM card. Just configure one according to your network configuration, see the example below. If you are starting with the default config from the source tree (
osmocom-bb/doc/examples/mobile/default.cfg), make sure to change
sim reader to
sim test in the
ms 1 section.
test-sim imsi 901700000000000 no barred-access rplmn 901 70
Make sure you have the virtual network running, then run mobile the same way as in case of a Calypso based phone:
$ cd osmocom-bb/src/host/layer23/src/mobile/ $ ./mobile -i 127.0.0.1
Now you can use mobile's telnet interface to manage your virtual phone:
$ telnet localhost 4247 $ ...
- Simulation and randomization of both RSSI and ToA
- Burst capture to file (see data_dump.py)
- Injection of bursts and commands
- Allow multiple BTS to work with multiple BB instances
- Distinguish debug messages (BTS / MS, ID)