Gapk » History » Revision 9
Revision 8 (fixeria, 07/16/2018 04:13 PM) → Revision 9/18 (fixeria, 07/16/2018 04:15 PM)
h1. GAPK (GSM Audio Pocket Knife) {{>toc}} The GAPK (GSM Audio Pocket Knife) is a project, the product of which is a core library (libosmogapk) and a command-line tool (osmo-gapk) for conversions between the various GSM related codecs (HR/FR/EFR/AMR) and PCM audio. It supports many different formats for the codec frames, including ETSI and IETF standardized formats, as well as vendor-specific formats like those found in the TI Calypso DSP (see [[OsmocomBB:]]) and those of Racal 6103/6113 GSM test equipment. h2. Supported Codecs |_.Codec|_.Description|_.Implementation| |pcm|Raw PCM signed 16bits samples|native| |hr|GSM 06.20 Half Rate codec|libgsmhr[1] (GSM 06.06 reference code)| |fr|GSM 06.10 Full Rate codec (classic gsm codec)|libgsm| |efr|GSM 06.60 Enhanced Full Rate codec|opencore-amr| |amr|GSM 26.061 Adaptive Multi Rate codec|opencore-amr| [1] Note: due to the licensing problems, the GSM 06.06 reference *code is not included* as a part of GAPK. Moreover, the reference implementation has some additional problems, such as relatively low performance and poor code quality (lots of warnings, global state variables). Passing the _--enable-gsmhr_ configuration flag will enable the source code downloading, patching and compilation. h2. Supported Formats |_.Format|_.Description| |amr-efr |Classic .amr file containing EFR (=AMR 12.2k) data| |gsm |Classic .gsm file format (and RTP payload for FR according to RFC3551)| |hr-ref-dec |3GPP HR Reference decoder code parameters file format| |hr-ref-enc |3GPP HR Reference encoder code parameters file format| |racal-hr |Racal HR TCH/H recording| |racal-fr |Racal FR TCH/F recording| |racal-efr |Racal EFR TCH/F recording| |rawpcm-s16le |Raw PCM samples Signed 16 bits little endian| |ti-hr |Texas Instrument HR TCH/H buffer format| |ti-fr |Texas Instrument FR TCH/F buffer format| |ti-efr |Texas Instrument EFR TCH/F buffer format| |amr-opencore |Input format to libopencore-amrnb| |rtp-amr |RTP payload for AMR according to RFC4867| |rtp-efr |RTP payload for EFR according to RFC3551| |rtp-hr-etsi |RTP payload for HR according to ETSI TS 101 318| |rtp-hr-ietf |RTP payload for HR according to IETF RFC5993| h2. Source Code You can find the source code in git: * http://git.osmocom.org/gapk/ (cgit web interface) * @git clone git://git.osmocom.org/gapk@ for cloning the repository h2. Common use cases h3. RTP sink with audio playback on sound card You can run @gapk@ as a _RTP sink_, i.e. listening to a given UDP port for incoming RTP frames, decoding them from their respective audio codec and then playing them back via your computers' sound card. <pre> $ gapk -I 0.0.0.0/30000 -f rtp-amr -A default -g rawpcm-s16le </pre> where * *@-I 0.0.0.0/30000@* indicates the IP adddress (any) and UDP port (30000) to bind to and receive RTP frames on * *@-f rtp-amr@* indicates the codec. Use *@gsm, rtp-efr, rtp-amr, rtp-hr-etsi or rtp-hr-ietf@* depending on your use case * *@-A default@* is the alsa hardware device name (default is the default sound card) h2. Source Code You can find the source code in git: * http://git.osmocom.org/gapk/ (cgit web interface) * @git clone git://git.osmocom.org/gapk@ for cloning the repository h2. Contact / Mailing List The project is too small to have it's own mailing list. Instead, we use the openbsc@lists.osmocom.org mailing list ("subscribe":http://lists.osmocom.org/mailman/listinfo/OpenBSC). Please observe the [[cellular-infrastructure:Mailing_List_Rules]]. h2. Authors @gapk@ as written by Sylvain Munaut with contributions from Harald Welte. It uses external libraries for the actual audio codecs, such as @libgsm@, @libopencore-amrnb@ nd the ETSI reference implementation for GSM-HR.