E3533 » History » Revision 6
Revision 5 (demodulate, 10/04/2017 02:58 PM) → Revision 6/13 (demodulate, 10/04/2017 03:04 PM)
h1. E3533
The E3533 HSPA+ USB stick is a USB type-A device with a single SIM slot. The E3533 appears to use a HiSilicon chipset. It has an external antenna connector inside of the
case which is not exposed to the end user without disassembly. The E3533 costs around 35 Euro at Media Markt unlocked and without ties to a specific carrier. The [[E3531]] is usually available for 15 Euro locked to O2 and it requires ID to purchase because of the included SIM card.
h2. Chipset information
According to a published Huawei technical document about the CH1E3533SM device we know the following details:
<pre>
Hardware Version:
CH1E3533SM
Platform & Chipset:
Balong V3R3
BB Hi6758
PMU Hi6561
RFIC Hi6361
</pre>
More information about the platform and each chipset is welcome.
FCC documents:
https://fccid.io/QISE3533S-58
Upon insertion @lsusb@ reports:
<pre>
Bus 001 Device 115: ID 12d1:157d Huawei Technologies Co., Ltd.
</pre>
The @dmesg@ entries generated on first insert show an emulated CD-ROM and a cdc_mbim device:
<pre>
[749819.192948] usb 1-1.2: New USB device found, idVendor=12d1, idProduct=157d
[749819.192955] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[749819.192959] usb 1-1.2: Product: HUAWEI Mobile
[749819.192961] usb 1-1.2: Manufacturer: HUAWEI
[749819.192963] usb 1-1.2: SerialNumber: FFFFFFFFFFFFFFFF
[749819.251102] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[749819.251591] scsi host6: usb-storage 1-1.2:1.0
[749819.971474] usb 1-1.2: usbfs: interface 0 claimed by usb-storage while 'usb_modeswitch' sets config #2
[749820.191555] cdc_mbim 1-1.2:2.0: SET_NTB_FORMAT failed
[749820.220636] cdc_mbim 1-1.2:2.0: bind() failure
[749820.404469] usb 1-1.2: USB disconnect, device number 46
[749824.924301] usb 1-1.2: new high-speed USB device number 47 using ehci-pci
[749825.036441] usb 1-1.2: New USB device found, idVendor=12d1, idProduct=157d
[749825.036449] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[749825.036453] usb 1-1.2: Product: HUAWEI Mobile
[749825.036455] usb 1-1.2: Manufacturer: HUAWEI
[749825.036458] usb 1-1.2: SerialNumber: FFFFFFFFFFFFFFFF
[749825.088470] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[749825.088940] scsi host6: usb-storage 1-1.2:1.0
[749826.129411] scsi 6:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[749826.254200] sr 6:0:0:0: [sr0] scsi-1 drive
[749826.254681] sr 6:0:0:0: Attached scsi CD-ROM sr0
[749826.254999] sr 6:0:0:0: Attached scsi generic sg1 type 5
[749829.765943] ISO 9660 Extensions: Microsoft Joliet Level 1
[749829.766741] ISOFS: changing to secondary root
</pre>
The MBIM device does not always properly initialize on a 4.9.33 kernel. If it doesn't there is an error:
<pre>
[749820.191555] cdc_mbim 1-1.2:2.0: SET_NTB_FORMAT failed
[749820.220636] cdc_mbim 1-1.2:2.0: bind() failure
</pre>
If the MBIM device does properly initialize it may present as follows:
<pre>
[759552.947138] cdc_mbim 1-1.2:2.0: NDP will be placed at end of frame for this device.
[759552.947675] cdc_mbim 1-1.2:2.0: cdc-wdm0: USB WDM device
[759552.948368] cdc_mbim 1-1.2:2.0 wwan0: register 'cdc_mbim' at usb-0000:00:1a.0-1.2, CDC MBIM, bb:cc:dd:ee:ff:ff
[759552.955609] cdc_mbim 1-1.2:2.0 wwp0sXXXXXXXXX: renamed from wwan0
[759552.995969] usb 1-1.2: USB disconnect, device number 78
[759552.996056] cdc_mbim 1-1.2:2.0 wwp0sXXXXXXXXX:: unregister 'cdc_mbim' usb-0000:00:1a.0-1.2, CDC MBIM
</pre>
h2. Modem details
@ATI@ output:
<pre>
Manufacturer: huawei
Model: E3533
Revision: 22.318.25.00.414
IMEI: 000000000000000
+GCAP: +CGSM,+DS,+ES
</pre>
@AT^VERSION?@ output:
<pre>
^VERSION:BDT:Mar 26 2014, 17:17:00
^VERSION:EXTS:22.318.25.00.414
^VERSION:INTS:22.318.25.00.414
^VERSION:EXTD:WEBUI_15.100.10.00.414
^VERSION:INTD:WEBUI_15.100.10.00.414
^VERSION:EXTH:CH1E3533SM
^VERSION:INTH:CH1E3533SM Ver.A
^VERSION:EXTU:E3533
^VERSION:INTU:E3533s-2EA
^VERSION:CFG:1004
^VERSION:PRL:
^VERSION:INI:
</pre>
@AT^DLOADINFO?@ output:
<pre>
swver:22.318.25.00.414
isover:WEBUI_15.100.10.00.414
webuiver:
product name:E3533s-2EA
dload type:0
</pre>
@AT^HWVER@ output:
<pre>
^HWVER:"CH1E3533SM"
</pre>
h2. Modem configuration
The E3533 modem may be reconfigured in at least four ways:
* @usb_modeswitch@
* Sending @AT^SETMODE=0@ or @AT^SETMODE=1@ using /dev/ttyUSB0
* Posting an XML request to the internal webserver listening on 192.168.8.1 when the device is in cdc_ethernet mode
* @AT^GODLOAD@
h2. Reconfigure the modem with usb_modeswitch:
Serial port with three ttyUSB devices:
<pre>@usb_modeswitch -v 12d1 -p 157d -V 0x12d1 -P 0x157d --message-content "5553424312345678000000000000001106200000010000000
0000000000000" -s 60</pre>
@lsusb@ shows:
<pre>
Bus 001 Device 028: ID 12d1:1001 Huawei Technologies Co., Ltd. E169/E620/E800 HSDPA Modem
</pre>
@dmesg@ shows:
<pre>
[749902.292987] usb 1-1.2: new high-speed USB device number 48 using ehci-pci
[749902.403329] usb 1-1.2: New USB device found, idVendor=12d1, idProduct=1001
[749902.403334] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[749902.403337] usb 1-1.2: Product: HUAWEI Mobile
[749902.403338] usb 1-1.2: Manufacturer: HUAWEI
[749902.706904] option 1-1.2:1.0: GSM modem (1-port) converter detected
[749902.707141] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB0
[749902.707343] option 1-1.2:1.1: GSM modem (1-port) converter detected
[749902.707539] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB1
[749902.707708] option 1-1.2:1.2: GSM modem (1-port) converter detected
[749902.707894] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB2
</pre>
Ethernet with cdc_ethernet:
<pre>usb_modeswitch -v 12d1 -p 157d -V 0x12d1 -P 0x157d --message-content "55534243123456780000000000000a11062000000000000100000000000000" -s 60</pre>
@lsusb@ shows:
<pre>
Bus 001 Device 031: ID 12d1:14db Huawei Technologies Co., Ltd. E353/E3131
</pre>
@dmesg@ shows:
<pre>
[816071.162917] usb 1-1.2: new high-speed USB device number 119 using ehci-pci
[816071.277056] usb 1-1.2: New USB device found, idVendor=12d1, idProduct=14db
[816071.277062] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[816071.277065] usb 1-1.2: Product: HUAWEI Mobile
[816071.277067] usb 1-1.2: Manufacturer: HUAWEI
[816071.542615] cdc_ether 1-1.2:1.0 eth0: register 'cdc_ether' at usb-0000:00:1a.0-1.2, CDC Ethernet Device, 00:11:11:11:00:00
[816071.711157] cdc_ether 1-1.2:1.0 enx001111110000: renamed from eth0
[816073.487379] cdc_ether 1-1.2:1.0 enx001111110000: kevent 12 may have been dropped
</pre>
h2. Debug mode serial ports
After insertion and reconfiguration to cdc_ethernet, it is possible to interact with the web service on the modem to enable a debug mode.
This XML file switches it into a debug mode where additional AT commands are available:
<pre>
cat << 'EOF' >> debug.xml
<?xml version="1.0" encoding="UTF-8" ?>
<api version="1.0">
<header>
<function>switchMode</function>
</header>
<body>
<request>
<switchType>1</switchType>
</request>
</body>
</api>
EOF
</pre>
Enable the single serial port mode:
<pre>cat debug.xml | curl -X POST -d @- http://192.168.8.1/CGI</pre>
@lsusb@ shows:
<pre>
Bus 001 Device 032: ID 12d1:1001 Huawei Technologies Co., Ltd. E169/E620/E800 HSDPA Modem
</pre>
@dmesg@ shows:
<pre>
[748005.066836] usb 1-1.2: new high-speed USB device number 32 using ehci-pci
[748005.178045] usb 1-1.2: New USB device found, idVendor=12d1, idProduct=1001
[748005.178053] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[748005.178057] usb 1-1.2: Product: HUAWEI Mobile
[748005.178060] usb 1-1.2: Manufacturer: HUAWEI
[748005.367337] option 1-1.2:1.0: GSM modem (1-port) converter detected
[748005.367991] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB0
</pre>
h2. GODLOAD mode serial port
It is possible to enable a currently undocumented two serial port mode from the single serial port mode.
While configured in debug mode, open /dev/ttyUSB0 and issue the @AT^GOADLOAD@ command. This will close /dev/ttyUSB0 and open two other /dev/ttyUSB0 and /dev/ttyUSB1 devices. Neither device responds to the AT command set.
@lsusb@ shows:
<pre>
Bus 001 Device 124: ID 12d1:1442 Huawei Technologies Co., Ltd.
</pre>
@dmesg@ shows:
<pre>
[818963.315945] usb 1-1.2: New USB device found, idVendor=12d1, idProduct=1442
[818963.315953] usb 1-1.2: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[818963.315956] usb 1-1.2: Product: HUAWEI Mobile
[818963.315959] usb 1-1.2: Manufacturer: HUAWEI Technology
[818963.317395] option 1-1.2:1.0: GSM modem (1-port) converter detected
[818963.319958] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB0
[818963.320236] option 1-1.2:1.1: GSM modem (1-port) converter detected
[818963.320610] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB1
</pre>
h2. Exploring the emulated CD-ROM
In the initial mode, a CD-ROM is emulated.
It is possible to mount this disk:
<pre>
mount /dev/sr0 /mnt/
mount: /dev/sr0 is write-protected, mounting read-only
</pre>
It contains various drivers for the modem itself:
<pre>
$ ls -l
total 582
-r-------- 1 user user 1523 Feb 19 2014 ArConfig.dat
-r-------- 1 user user 142416 Jul 24 2013 AutoRun.exe
-r-------- 1 user user 45 Jun 22 2011 AUTORUN.INF
-r-------- 1 user user 94 Apr 5 2011 autorun.sh
dr-x------ 1 user user 2048 Feb 19 2014 HiLink.app
-r-------- 1 user user 3262 Jun 23 2011 install_linux
dr-x------ 1 user user 2048 Feb 19 2014 linux_mbb_install
dr-x------ 1 user user 2048 Feb 19 2014 MobileBrServ
-r-------- 1 user user 439926 Dec 1 2010 Startup.ico
</pre>
The install_linux modem software inspected reports as version 22.001.03.01.03.
h2. Exploring the cdc_ethernet mode
The cdc_ethernet mode creates an ethernet device on your computer. It is possible to change the MAC address of the presented cdc_ethernet device with ip and ifconfig as if it were a normal ethernet device. Using DHCP on this interface will result in being assigned an address in the 192.168.8.100-254 range. The default route is 192.168.8.1. The device itself has a clock which is exposed in ICMP, DHCP, and HTTP requests. They're not all in sync.
This default router address 192.168.8.1 exposes DNS, DHCPD, HTTPD and a UPnP daemon:
<pre>
DHCPD - unknown server - other than 192.168.8.1 as router/dns it reports hi.link as the dns search domain
DNS - fpdns says: fingerprint (192.168.8.1, 192.168.8.1): Meilof Veeningen Posadis [Old Rules]
DNS - nmap says ISC BIND (Fake version: [secured])
HTTPD - webui: 192.168.8.1 - mini_httpd/1.19 19dec2003
UPnP- http://192.168.8.1:45532/ is UPNP HTTPD server - Server: E588 UPnP/1.0 MiniUPnPd/1.6
</pre>
TCP port scan:
<pre>
Not shown: 65391 closed ports, 142 filtered ports
PORT STATE SERVICE VERSION
53/tcp open domain
80/tcp open http mini_httpd 1.19 19dec2003
45532/tcp open upnp
</pre>
UDP port scan:
<pre>
53/udp open domain ISC BIND (Fake version: [secured])
67/udp open|filtered dhcps
</pre>
UPnP probe with <pre>upnpc -s</pre>:
<pre>
desc: http://192.168.8.1:45532/rootDesc.xml
st: urn:schemas-upnp-org:device:InternetGatewayDevice:1
Found valid IGD : http://192.168.8.1:45532/ctl/IPConn
Local LAN ip address : 192.168.8.100
Connection Type : IP_Routed
Status : Connected, uptime=1506822734s, LastConnectionError : ERROR_NONE
Time started : Wed Dec 31 22:59:22 1969
MaxBitRateDown : 4200000 bps (4.2 Mbps) MaxBitRateUp 4200000 bps (4.2 Mbps)
ExternalIPAddress = 10.75.35.236
Bytes: Sent: 18531306 Recv: 19775523
Packets: Sent: 23563 Recv: 22563
</pre>
As with 192.168.8.1, the 10.75.35.236 device directly ARPs to us:
<pre>
42 bytes from 00:11:22:33:44:55 (10.75.35.236): index=0 time=14.255 msec
42 bytes from 00:11:22:33:44:55 (10.75.35.236): index=1 time=5.195 msec
</pre>
A scan of the 10.75.35.236 address reveals similar services as 192.168.8.1 while possibly making them available to the outside world:
<pre>
Nmap scan report for 10.75.35.236
Host is up (0.0013s latency).
PORT STATE SERVICE VERSION
1/tcp closed tcpmux
53/tcp open tcpwrapped
80/tcp open http mini_httpd 1.19 19dec2003
|_http-title: Did not follow redirect to http://192.168.8.1/html/index.html?url=10.75.35.236
123/tcp closed ntp
</pre>
These services may provide a TR-069 https://en.wikipedia.org/wiki/TR-069 interface. There appears to be no authentication to access the web service at all.
h2. AT commands
Depending on the mode of operations, different AT commands are available - the default three serial port mode is restricted and the single serial port debug mode appears to allow many additional commands.
h2. Firmware
Firmware is available as an OTA update from within the web interface. It is possible to query for a firmware update and the device will connect to a Huawei webserver to see if there are firmware updates. The update process is currently undocumented.
Firmware appears to be available from various Huawei servers and through careful querying it is possible to create a list as one internet user has published: https://gist.github.com/ValdikSS/f0f0d5ab9444b74ffedb7a41572bbbb5
Relevant firmware for the E3533 is available at the following urls:
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v60716/f1/full/E3533_All_UPDATE_22.318.39.00.105_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v61754/f1/full/E3533_All_UPDATE_22.318.39.00.105_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v64855/f1/full/E3533_All_UPDATE_22.318.39.00.105_gz.BIN
Firmware for the E3531 is available as well:
http://update.hicloud.com:8180/TDS/data/files/p9/s43/G134/g1/v29051/f1/full/E3531_All_UPDATE_22.318.35.00.916_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s43/G134/g1/v85063/f1/full/E3531_FW_UPDATE_22.318.31.01.00.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s92/G247/g0/v50833/f1/full/E3531_All_UPDATE_22.318.35.00.225_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s92/G247/g0/v51374/f1/full/E3531_All_UPDATE_22.318.35.00.370_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s92/G247/g0/v55519/f1/full/E3531_All_UPDATE_22.521.31.01.408_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s93/G249/g0/v38584/f1/full/E3531_All_UPDATE_22.521.31.01.801_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s93/G249/g0/v38958/f1/full/E3531_All_UPDATE_22.318.35.00.422_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s93/G249/g0/v42810/f1/full/E3531_All_UPDATE_22.521.31.00.1036_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s93/G249/g0/v44501/f1/full/E3531_All_UPDATE_22.318.35.00.07_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s93/G249/g0/v77588/f1/full/E3531i-2_All_UPDATE_22.521.35.00.801_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s93/G249/g0/v81503/f1/full/E3531i-2_All_UPDATE_22.521.35.00.61_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s93/G249/g0/v85007/f1/full/E3531Update_21.318.35.01.26.zip
http://update.hicloud.com:8180/TDS/data/files/p9/s93/G249/g0/v85008/f1/full/E3531UPDATE_21.318.35.01.26.exe
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v26461/f1/full/E3531_All_UPDATE_22.521.31.02.40_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v27507/f1/full/E3531_All_UPDATE_22.318.35.00.40_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v28924/f1/full/E3531Update_21.521.31.02.382.zip
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v28925/f1/full/E3531UPDATE_21.521.31.02.382.exe
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v36752/f1/full/E3531_All_UPDATE_22.318.35.00.705_gz.BIN
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v85083/f1/full/E3531UPDATE_21.521.35.00.382.exe
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v85084/f1/full/E3531Update_21.521.35.00.382.zip
http://update.hicloud.com:8180/TDS/data/files/p9/s94/G251/g0/v91656/f1/full/E3531Update_21.318.35.00.382.zip
Other firmware and related files are floating around on the internet:
<pre>
E3531_E3533Update_22.318.05.00.00.7z
E3531&E3533_UPDATE_22.318.05.00.00.exe
E3533_All_UPDATE_22.318.39.00.105_gz.BIN
E3533_All_UPDATE_22.318.39.00.105_gz.BIN.changelog.xml
E3533s-2_22.318.23.00.105_T-Mobile.7z
E3533s-2_22.318.27.00.441_Tele2_Kazakhstan.7z
E3533s-2TCPU-22.318.27.00.441 Release Notes.pdf
E3533s-2TCPU-V200R002B318D27SP00C441&WEBUI-V100R005B100D10SP01C441 Version Configuration Information Form.doc
E3533s TCPU-22.318.23.00.105 Release Notes.pdf
E3533s_WEBUI-15.100.03.00.03_Universal.zip
E3533_UPDATE_22.318.23.00.105.BIN
E3533_UPDATE_22.318.23.00.105.exe
E3533UPDATE_22.318.27.00.441.BIN
E3533UPDATE_22.318.27.00.441.BIN.asc
E3533UPDATE_22.318.27.00.441.exe
E3533UPDATE_22.318.27.00.441.exe.asc
SHA256_E3533s-2TCPU-V200R002B318D23SP00C105.html
</pre>
In each E3533 firmware examined, the firmware contains a VxWorks kernel, an Android kernel, multiple YAFFS file systems, and an ISO which is presented as the emulated CD-ROM. The firmware format is not yet documented. It is possible to use @binwalk@ to extract files and information.
h2. Flashing new firmware
This is currently undocumented. The apparent internet expert on similar modems is this github user:
https://github.com/forth32/balong-usbdload
https://github.com/forth32/balong-fbtools
https://github.com/forth32/balongflash
h2. Additional software
A number of strange cargo cult websites offer a bunch of non-free software to help reflash firmware, "reconfigure", or "unlock" the E3533 or similar devices. Some of this software should provide a basis for reverse engineering the flashing process and possibly provide information about the format or the firmware structure.
h2. Photos
[[E3533Images]]
h2. Hardware Serial console
There is possibly a serial console available. This has not been explored.
h2. Boot pin
On other Huawei devices a pad or pin may be grounded to provide a console and/or to interrupt the boot loader.
The boot pin is undocumented and is possible similar to others which are documented: https://routerunlock.com/boot-pin-of-different-huawei-hi-silicon-modem-and-router/
h2. Possibly related links
http://www.gnuton.org/blog/2015/07/huawei-e3372/
http://www.gnuton.org/blog/2015/08/huawei-e3371-part-2-at-commands/
http://blog.asiantuntijakaveri.fi/2014/08/differences-of-huawei-b593u-and-b593s.html
https://gist.github.com/ValdikSS/323bcdfceb2f09d9c6ef02db1bc573e2
http://www.0xf8.org/2017/01/flashing-a-huawei-e3372h-4g-lte-stick-from-hilink-to-stick-mode/
https://www.dc-unlocker.com/huawei-e3533-unlock-guide
https://www.dc-unlocker.com/file-list/Firmwares/Huawei_modems/HiSilicon_platform/E3533
https://routerunlock.com/boot-pin-of-different-huawei-hi-silicon-modem-and-router/
https://www.unlockmyrouter.com/bypass-datalock-code-installing-huawei-firmwares/
https://github.com/ilya-fedin/autoflash/blob/master/main.sh
https://www.unlock4modems.com/how-to-bypass-datalock-code-while-updating-firmware-of-huawei-algo-v4-modem/
https://forum.dc-unlocker.com/forum/modems-and-phones/huawei/14570-huawei-hisilicon-firmware-writer/page12