Bs11 config » History » Revision 10
Revision 9 (laforge, 02/19/2016 10:48 PM) → Revision 10/12 (laforge, 02/19/2016 10:48 PM)
{{>toc}} [[PageOutline]] bs11_config is a small commandline program that can be used to configure the [[BS-11]] [wiki:BS-11] BTS using its RS232 link. It can perform a subset of the functions that are typically performed using the Siemens LMT (Local Maintenance Terminal) software, such as * querying some essential configuration values * creating and deleting TRX1 objects * download of SAFETY LOAD software * download of BTS software * creating an initial configuration (such as creating BBSIG,CCLK,PA,... objects) * setting the Tx output power of the RF amplifier h2. == Reference h3. == === Querying the BS-11 <pre> === {{{ $ ./bs11_config -p /dev/ttyUSB0 query bs11_config (C) 2009 by Harald Welte and Dieter Spaar This is FREE SOFTWARE with ABSOLUTELY NO WARRANTY LMT LOGON: ACK PHASE: 3 Normal MBCCU0: Load MBCCU1: Load Abis-link: Restoring BS11 ATTRIBUTES: BS-11 ESN PCB Serial Number: 001107 BS-11 ESN Hardware Code Number: 135-2044/03.07 BS-11 ESN Firmware Code Number: 135-2044/03.07 SITE MANAGER ATTRIBUTES: E1 Channel: Port=0 Timeslot=1 (Full Slot) TEI: 25 BS11 Power Amplifier 0 ATTRIBUTES: TRX Power: 30mW (GSM) BS11 Power Amplifier 1 ATTRIBUTES: TRX Power: 30mW (GSM) </pre> h3. }}} === Disconnect === This puts the BTS out of Normal mode into Maintenance mode and disconnects it from the BSC <pre> {{{ $ ./bs11_config -p /dev/ttyUSB0 disconnect bs11_config (C) 2009 by Harald Welte and Dieter Spaar This is FREE SOFTWARE with ABSOLUTELY NO WARRANTY LMT LOGON: ACK PHASE: 3 Normal MBCCU0: Load MBCCU1: Load Abis-link: Restoring PHASE: 2 Maintenance MBCCU0: Load MBCCU1: Load Abis-link: Down </pre> h3. }}} === Reconnect === This puts the BTS out of Maintenance mode into Normal mode and reconnects it to the BSC <pre> {{{ $ ./bs11_config -p /dev/ttyUSB0 reconnect bs11_config (C) 2009 by Harald Welte and Dieter Spaar This is FREE SOFTWARE with ABSOLUTELY NO WARRANTY LMT LOGON: ACK PHASE: 2 Maintenance MBCCU0: Load MBCCU1: Load Abis-link: Down PHASE: 3 Normal MBCCU0: Load MBCCU1: Load Abis-link: Restoring </pre> h3. }}} === Download SMU Safety Load <pre> === {{{ $ ./bs11_config -p /dev/ttyUSB0 -S /path/to/my/BTSBMC76.SWI </pre> }}} Note: When the SMU Safety download has completed and the minimal configuration has been created you should let the BS11 boot the first time. The power LED will light up red - this is normal. After the boot you will be able to query the BS11. Bring it into the maintenance (disconnect) mode and proceed with the software download. *NOTE: '''NOTE: The [[OpenBSC]]/bs11-abis OpenBSC/bs11-abis project is not providing any Firmware images for the BS-11, as they are copyrighted material* h3. material''' === Minimal Configuration === The minimal configuration is automatically created if the BS-11 enters the _MINIMAL ''MINIMAL CONFIG REQUIRED_ REQUIRED'' state after the SMU safety load is installed. h3. === Download Software Load <pre> === {{{ $ ./bs11_config -p /dev/ttyUSB0 -s /path/to/my/HS011106.SWL </pre> }}} If the BS-11 is not in Maintenance State, it first needs to be detached from the BSC (using -D option) <pre> {{{ $ ./bs11_config -p /dev/ttyUSB0 -D -s /path/to/my/HS011106.SWL </pre> }}} If you want to force a download, just add the _-f_ ''-f'' parameter. The described procedure lasts for about a hour and should generate the following output: <pre> {{{ ./bs11_config -s bs11-flash/HS011106.SWL software bs11_config (C) 2009 by Harald Welte and Dieter Spaar This is FREE SOFTWARE with ABSOLUTELY NO WARRANTY LMT LOGON: ACK PHASE: 2 Maintenance MBCCU0: No Load MBCCU1: No Load Abis-link: Down Mon May 18 20:51:34 2009 <0020> abis_nm.c:1337 Software Load (BTS 0, File "bs11-flash/HS011106.SWL") Software Load Initiate ACK Software Download Progress: 88% Software Download Progress: 100% Mon May 18 20:51:37 2009 <0020> abis_nm.c:1261 Software Load End (BTS 0) Mon May 18 20:51:37 2009 <0020> abis_nm.c:1337 Software Load (BTS 0, File "bs11-flash/VS011106.VAM") Mon May 18 20:51:37 2009 <0020> abis_nm.c:1323 unexpected NM MT 0x08 in state 3 -> 1 ERROR in main loop: Success Software Load Initiate ACK Software Download Progress: 100% Mon May 18 20:51:38 2009 <0020> abis_nm.c:1261 Software Load End (BTS 0) Mon May 18 20:51:38 2009 <0020> abis_nm.c:1337 Software Load (BTS 0, File "bs11-flash/BTSBMC48.SWI") Mon May 18 20:51:38 2009 <0020> abis_nm.c:1323 unexpected NM MT 0x08 in state 3 -> 1 ERROR in main loop: Success PHASE: 2 Maintenance MBCCU0: No Load MBCCU1: No Load Abis-link: Down Software Load Initiate ACK Software Download Progress: 1% --- cut --- Software Download Progress: 100% Mon May 18 21:04:05 2009 <0020> abis_nm.c:1261 Software Load End (BTS 0) Mon May 18 21:04:05 2009 <0020> abis_nm.c:1337 Software Load (BTS 0, File "bs11-flash/BTSCAC11.SWI") Mon May 18 21:04:05 2009 <0020> abis_nm.c:1323 unexpected NM MT 0x08 in state 3 -> 1 ERROR in main loop: Success Software Load Initiate ACK Software Download Progress: 1% --- cut --- Software Download Progress: 100% Mon May 18 21:10:03 2009 <0020> abis_nm.c:1261 Software Load End (BTS 0) Mon May 18 21:10:03 2009 <0020> abis_nm.c:1337 Software Load (BTS 0, File "bs11-flash/BTSDRX22.SWI") Mon May 18 21:10:03 2009 <0020> abis_nm.c:1323 unexpected NM MT 0x08 in state 3 -> 1 ERROR in main loop: Success Software Load Initiate ACK Software Download Progress: 1% --- cut --- Software Download Progress: 100% Mon May 18 21:20:31 2009 <0020> abis_nm.c:1261 Software Load End (BTS 0) Mon May 18 21:20:31 2009 <0020> abis_nm.c:1337 Software Load (BTS 0, File "bs11-flash/BTSBBX12.SWI") Mon May 18 21:20:31 2009 <0020> abis_nm.c:1323 unexpected NM MT 0x08 in state 3 -> 1 ERROR in main loop: Success Software Load Initiate ACK Software Download Progress: 1% --- cut --- Software Download Progress: 100% Mon May 18 21:26:23 2009 <0020> abis_nm.c:1261 Software Load End (BTS 0) Mon May 18 21:26:23 2009 <0020> abis_nm.c:1337 Software Load (BTS 0, File "bs11-flash/BTSARC16.SWI") Mon May 18 21:26:23 2009 <0020> abis_nm.c:1323 unexpected NM MT 0x08 in state 3 -> 1 ERROR in main loop: Success Software Load Initiate ACK Software Download Progress: 1% --- cut --- Software Download Progress: 100% Mon May 18 21:32:53 2009 <0020> abis_nm.c:1261 Software Load End (BTS 0) Mon May 18 21:32:53 2009 <0020> abis_nm.c:1337 Software Load (BTS 0, File "bs11-flash/BTSLIC10.SWI") Mon May 18 21:32:53 2009 <0020> abis_nm.c:1323 unexpected NM MT 0x08 in state 3 -> 1 ERROR in main loop: Success Software Load Initiate ACK Software Download Progress: 1% --- cut --- oftware Download Progress: 100% Mon May 18 21:35:10 2009 <0020> abis_nm.c:1261 Software Load End (BTS 0) Mon May 18 21:35:10 2009 <0020> abis_nm.c:1386 Activating Software (BTS 0, File "bs11-flash/HS011106.SWL") Mon May 18 21:35:10 2009 <0020> abis_nm.c:1323 unexpected NM MT 0x08 in state 3 -> 4 ERROR in main loop: Success Mon May 18 21:35:11 2009 <0020> abis_nm.c:1292 Activate Software DONE! PHASE: 1 Warm Up MBCCU0: No Load MBCCU1: No Load Abis-link: Down LMT LOGON: ACK LMT LOGON: ACK PHASE: 1 Warm Up MBCCU0: No Load MBCCU1: No Load Abis-link: Down PHASE: 1 Warm Up MBCCU0: No Load MBCCU1: No Load Abis-link: Down PHASE: 1 Warm Up Abis-link: Down --- cut --- PHASE: 1 Load SMU Intended Abis-link: Down --- cut --- PHASE: 2 Load MBCCU MBCCU0: No Load MBCCU1: No Load Abis-link: Down PHASE: 2 Load MBCCU MBCCU0: Load BTSCAC MBCCU1: No Load Abis-link: Down PHASE: 2 Load MBCCU MBCCU0: Load BTSDRX MBCCU1: No Load Abis-link: Down PHASE: 2 Load MBCCU MBCCU0: Load BTSBBX MBCCU1: No Load Abis-link: Down PHASE: 2 Load MBCCU MBCCU0: Load BTSARC MBCCU1: No Load Abis-link: Down PHASE: 2 Load MBCCU MBCCU0: Load MBCCU1: No Load Abis-link: Down PHASE: 2 Warm Up MBCCU0: Load MBCCU1: No Load Abis-link: Down PHASE: 3 Normal MBCCU0: Load MBCCU1: No Load Abis-link: Restoring </pre> *NOTE: [[OpenBSC]] }}} '''NOTE: OpenBSC is not providing any Firmware images for the BS-11* h3. BS-11''' === Observing BS-11 boot process === This is the output of bs11_config while observing the boot process. You will see every line many times, as the status is refreshed every five seconds. <pre> {{{ $./bs11_config -p /dev/ttyUSB0 bs11_config (C) 2009 by Harald Welte and Dieter Spaar This is FREE SOFTWARE with ABSOLUTELY NO WARRANTY LMT LOGON: ACK T-Link: Down Abis-link: Down MBCCU0: No Load MBCCU1: No Load PHASE: 1 SUBPHASE: Warm Up... T-Link: Down Abis-link: Down MBCCU0: No Load MBCCU1: No Load PHASE: 1 SUBPHASE: Load SMU Intended... T-Link: Down Abis-link: Down MBCCU0: No Load MBCCU1: No Load PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: No Load MBCCU1: Load BTSCAC PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: Load BTSCAC MBCCU1: Load BTSCAC PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: Load BTSCAC MBCCU1: Load BTSDRX PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: Load BTSDRX MBCCU1: Load BTSDRX PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: Load BTSDRX MBCCU1: Load BTSBBX PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: Load BTSBBX MBCCU1: Load BTSBBX PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: Load BTSBBX MBCCU1: Load BTSARC PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: Load BTSARC MBCCU1: Load BTSARC PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: Load BTSARC MBCCU1: Load PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Down MBCCU0: Load MBCCU1: Load PHASE: 2 SUBPHASE: Load MBCCU... T-Link: Down Abis-link: Restoring MBCCU0: Load MBCCU1: Load PHASE: 3 SUBPHASE: Normal... T-Link: Down Abis-link: Up MBCCU0: Load MBCCU1: Load PHASE: 3 SUBPHASE: Normal... </pre> h3. }}} === Configuring Multi-Drop setup === A multi-drop setup is where multiple BS-11 are daisy-chained next to each other on a single E1 line. All but the last BS-11 in the chain will have to be configured to * have BPORT0 in multi-drop mode * create a BPORT1 object * have BPORT1 to be set in multi-drop mode. You can achieve this by the following bs11_config command sequence: <pre> {{{ $ ./bs11_config bport0-multidrop $ ./bs11_config create-bport1 $ ./bs11_config bport1-multidrop </pre> }}} You can verify the results to show in *query* '''query''' like this: <pre> {{{ BPORT0 ATTRIBUTES: Line Configuration: Multi-Drop (1) BPORT1 ATTRIBUTES: Line Configuration: Multi-Drop (1) </pre> }}}