Project

General

Profile

EC20 » History » Version 18

ynezz, 01/08/2017 11:52 PM
Remove duplicate line from console output

1 13 neels
{{>toc}}
2
3 14 neels
h1. EC20
4 1 zecke
5 15 laforge
The Quectel EC20 is a LTE Modem Module manufactured by the Chinese Company Quectel. It is available as solder-type version but also as miniPCIe card.  There are different regional versions with different bands implemented.
6
7
It is based around the Qualcomm MDM9615 and runs an [[Qualcomm_OE_MSM|OE based Linux distribution]] on its internal Cortex-A5 core. This Linux on Cortex-A5 is what implements the USB device that you see from the host PC!
8 3 zecke
9 14 neels
h2. How does it work?
10 3 zecke
11 1 zecke
If on Host-PC I have ttyUSB3.. and I type AT. How does it end up at the modem? On the Linux side there is @atfwd_daemon@ that registers with a local ril daemon but how is USB connected. Who is bouncing things back to it or is Linux forwarding everything..
12 8 laforge
13
* the USB gadget (client) is entirely managed by the Linux on the Cortex-A5.
14
* the individual gadgets are implemented by drivers like f_diag.c or f_serial.c
15
* @f_serial.c@ seems to be able to connect each virtual serial port to a number of different transports:
16
** xport_tty (/dev/ttyGS* device to userspace using @u_serial.c@)
17
** xport_sdio (forwarding via SDIO using @u_sdio.c@)
18 1 zecke
** xport_smd (fowarding via shared memory to different CPU core using @u_smd.c@)
19 8 laforge
** xport_hsic (forwarding to different processor via GSIC using @u_{data,ctrl}_hsic.c@)
20
** xport_hsuart (forwarding via high-speed uart for DUN/RMNET via @u_data_hsuart.c@)
21 1 zecke
22 14 neels
h2. LED
23 8 laforge
24 12 laforge
GPIO90 seems to be the WWAN LED, quectel_daemon controls it via @echo 0|1 > /sys/class/gpio/gpio90/value@
25 1 zecke
26 14 neels
h2. Power management
27 3 zecke
28 1 zecke
Sleep/Power off seem to be "intercepted" by @atfwd_daemon@ that can execute "echo mem > /sys/power/state". Let's explore other options for wakeup. Is there a RTC?
29 3 zecke
30
31 14 neels
h2. Firmware updates with FOTA
32 3 zecke
33
APN for OTA is configured separately on UC20, assumingly the same applies for EC20. A update.zip will be stored on the "cache" partition and it looks like the recovery system will be booted. I guess that then the reocvery system will unpack the update.zip and flash the partitions.
34
35 14 neels
h2. Debugging with ADB
36 3 zecke
37 16 laforge
The modem has @adbd@ running, but doesn't export its USB endpoints by default.  The default USB descriptors look like this
38
|_.Interface|_.Function|
39
|0|DIAG|
40
|1|NMEA|
41
|2|AT|
42
|3|AT|
43
|4|RMNET|
44
45
Using @AT+QLINUXCMD="/usr/bin/usb_uartdiag"@ you can change the USB Interface/Endpoint configuration to 
46
47
|_.Interface|_.Function|
48
|0|ADB|
49
|1|DIAG|
50
|2|NMEA|
51
|3|AT|
52
|4|AT|
53
|5|RMNET
54
55
Please note that you will need to modify your kernel driver (see [[Improved_Linux_USB_Driver]]) accordingly after making this change.
56
57 1 zecke
Switching on adb (or fastboot or debug to NMEA console)
58
59 16 laforge
Other options for accessing a shell:
60
61 1 zecke
<pre>
62
AT+QFASTBOOT
63
AT+QLINUXCMD="echo foo > /dev/ttyGS0"
64
AT+QLINUXCMD="ps axuw > /dev/ttyGS0"
65
AT+QLINUXCMD="cat /usr/bin/usb_uartdiag > /dev/ttyGS0"
66 17 ynezz
</pre>
67 1 zecke
68 17 ynezz
<pre>
69 1 zecke
adb shell
70
# /
71 17 ynezz
</pre>
72
73
<pre>
74
root@gaben:~# echo -e 'AT+QLINUXCMD="/sbin/getty -L ttyGS0 115200 console"\r\n' > /dev/ttyUSB2
75
root@gaben:~# microcom /dev/ttyUSB1
76
77
OpenEmbedded Linux 9615-cdp ttyGS0
78
79
msm 20160923 9615-cdp ttyGS0
80
81
9615-cdp login: root
82
Password: oelinux123
83
root@9615-cdp:~# 
84 4 zecke
</pre>
85 1 zecke
86 14 neels
h2. fastboot / flashing
87 9 laforge
88
The appsboot.mbn we know of (sha1sum 8d47d7e8ca8a15ff089994d87e36b531f36f907a) has no signature and no certificate chain.  This information is established by looking at the image header, whose formta is "documented" in https://android.googlesource.com/kernel/lk/+/caf/master/target/mdm9615/tools/mkheader.c
89
90
91 14 neels
h2. full lsof output
92 1 zecke
93 6 zecke
[[LsOfOutput]]
94 5 zecke
95 14 neels
h2. ps
96 1 zecke
97 4 zecke
<pre>
98 3 zecke
/ # ps
99
PID   USER     TIME   COMMAND
100
   1 root       0:01 init [5]
101
   2 root       0:00 [kthreadd]
102
   3 root       0:00 [ksoftirqd/0]
103
   4 root       0:00 [kworker/0:0]
104
   6 root       0:00 [khelper]
105
   7 root       0:00 [netns]
106
   8 root       0:00 [sync_supers]
107
   9 root       0:00 [bdi-default]
108
  10 root       0:00 [kblockd]
109
  11 root       0:00 [khubd]
110
  12 root       0:00 [kworker/0:1]
111
  13 root       0:00 [modem_notifier]
112
  14 root       0:00 [smd_channel_clo]
113
  15 root       0:00 [smsm_cb_wq]
114
  16 root       0:00 [kworker/u:1]
115
  17 root       0:00 [qmi]
116
  18 root       0:00 [nmea]
117
  19 root       0:00 [RPCRPY_CNTL]
118
  20 root       0:00 [IPCRTR]
119
  21 root       0:00 [msm_ipc_router]
120
  22 root       0:00 [ipc_rtr_smd_rpc]
121
  23 root       0:00 [kworker/u:2]
122
  24 root       0:00 [apr_driver]
123
  25 root       0:00 [kswapd0]
124
  26 root       0:00 [ipc_rtr_q6_ipcr]
125
  27 root       0:00 [fsnotify_mark]
126
  28 root       0:00 [crypto]
127
  40 root       0:00 [quec_dtr]
128
  41 root       0:00 [mtdblock0]
129
  42 root       0:00 [mtdblock1]
130
  43 root       0:00 [mtdblock2]
131
  44 root       0:00 [mtdblock3]
132
  45 root       0:00 [mtdblock4]
133
  46 root       0:00 [mtdblock5]
134
  47 root       0:00 [mtdblock6]
135
  48 root       0:00 [mtdblock7]
136
  49 root       0:00 [mtdblock8]
137
  50 root       0:00 [mtdblock9]
138
  51 root       0:00 [mtdblock10]
139
  52 root       0:00 [mtdblock11]
140
  53 root       0:00 [mtdblock12]
141
  54 root       0:00 [mtdblock13]
142
  55 root       0:00 [mtdblock14]
143
  56 root       0:00 [mtdblock15]
144
  57 root       0:00 [spi_qsd.0]
145
  58 root       0:00 [mhsic_wq]
146
  59 root       0:00 [k_rmnet_mux_wor]
147
  60 root       0:00 [f_mtp]
148
  61 root       0:00 [file-storage]
149
  63 root       0:00 [uether]
150
  64 root       0:00 [diag_wq]
151
  65 root       0:00 [diag_cntl_wq]
152
  66 root       0:00 [iewq]
153
  67 root       0:00 [irq/368-msm-sdc]
154
  68 root       0:00 [usb_bam_wq]
155
  69 root       0:00 [bam_dmux_rx]
156
  70 root       0:00 [bam_dmux_tx]
157
  71 root       0:00 [deferwq]
158
  72 root       0:00 [yaffs-bg-1]
159
  92 root       0:00 [k_gserial]
160
  93 root       0:00 [k_gsmd]
161
  94 root       0:00 [k_gbam]
162
  95 root       0:00 [gsmd_ctrl]
163
 129 root       0:00 [yaffs-bg-1]
164
 140 root       0:00 [yaffs-bg-1]
165
 183 root       0:00 /sbin/adbd
166
 205 root       0:00 /usr/bin/time_daemon
167
 208 root       0:00 /usr/bin/wapfotadaemon
168
 211 root       0:00 /usr/bin/wapfotadaemon
169
 212 root       0:00 sh -c qmi_simple_ril_test modem_port=rmnet0 input=/usr/bi
170
 217 root       0:00 qmi_simple_ril_test modem_port=rmnet0 input=/usr/bin/comm
171
 224 nobody     0:00 /usr/bin/dnsmasq -7 /etc/dnsmasq.d
172
 227 root       0:00 qti
173
 231 root       0:00 /sbin/syslogd -n -C64 -m 20
174
 240 root       0:00 /usr/bin/diagrebootapp
175
 246 root       0:00 /usr/bin/atfwd_daemon
176
 256 root       0:00 /usr/bin/qmuxd
177
 272 root       0:00 /bin/sh /usr/sbin/restart_mbimd
178
 275 root       0:00 /usr/bin/netmgrd -u /etc/udhcpc.d/udhcpc.script
179
 280 root       0:00 /usr/bin/qmi_shutdown_modem
180
 284 root       0:03 /usr/bin/quectel_daemon
181
 304 root       0:00 /usr/bin/mbimd
182
 346 root       0:00 /sbin/reboot-daemon
183
 347 root       0:00 /sbin/getty -L ttyHSL0 115200 console
184
 364 root       0:00 /bin/sh /usr/bin/nmea_demon.sh ttyGS0
185
 367 root       0:00 quec_bridge /dev/nmea /dev/ttyGS0 s
186 1 zecke
 439 root       0:01 alsaucm_test
187 3 zecke
 453 root       0:00 [kworker/u:0]
188
 455 root       0:00 [kworker/u:3]
189
 457 root       0:00 [kworker/0:2]
190
 463 root       0:00 [flush-31:15]
191
 473 root       0:00 /bin/sh -
192
 477 root       0:00 [flush-31:14]
193
 478 root       0:00 ps
194 1 zecke
/ # 
195 4 zecke
</pre>
196 3 zecke
197 14 neels
h2. dmesg
198 1 zecke
199 4 zecke
<pre>
200 3 zecke
/ # dmesg
201
[    0.000000]   Normal zone: 9266 pages, LIFO batch:1
202
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
203
[    0.000000] pcpu-alloc: [0] 0 
204
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 9266
205
[    0.000000] Kernel command line: noinitrd root=/dev/mtdblock14 rw rootfstype=yaffs2 console=ttyHSL0,115200,n8 androidboot.hardware=qcom androidboot.serialno=MDM9615 androidboot.baseband=msm
206
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
207
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
208
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
209
[    0.000000] Memory: 15MB 22MB = 37MB total
210
[    0.000000] Memory: 29472k/29472k available, 9440k reserved, 0K highmem
211
[    0.000000] Virtual kernel memory layout:
212
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
213
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
214
[    0.000000]     DMA     : 0xff000000 - 0xffe00000   (  14 MB)
215
[    0.000000]     vmalloc : 0xc6800000 - 0xfa000000   ( 824 MB)
216
[    0.000000]     lowmem  : 0xc0000000 - 0xc6700000   ( 103 MB)
217
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
218
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
219
[    0.000000]       .init : 0xc0008000 - 0xc0032000   ( 168 kB)
220
[    0.000000]       .text : 0xc0032000 - 0xc05ad1d8   (5613 kB)
221
[    0.000000]       .data : 0xc05ae000 - 0xc061ab38   ( 435 kB)
222
[    0.000000]        .bss : 0xc061ab78 - 0xc07cd050   (1738 kB)
223
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
224
[    0.000000] Preemptible hierarchical RCU implementation.
225
[    0.000000] NR_IRQS:681
226
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30520ns, wraps every 131084001ms
227
[    0.000000] Console: colour dummy device 80x30
228
[    0.150190] Calibrating delay using timer specific routine.. 9.62 BogoMIPS (lpj=48102)
229
[    0.150221] pid_max: default: 32768 minimum: 301
230
[    0.150679] Mount-cache hash table entries: 512
231
[    0.151320] Initializing cgroup subsys debug
232
[    0.151350] Initializing cgroup subsys cpuacct
233
[    0.151381] Initializing cgroup subsys freezer
234
[    0.151442] CPU: Testing write buffer coherency: ok
235
[    0.157271] print_constraints: dummy: 
236
[    0.157668] NET: Registered protocol family 16
237
[    0.157820] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver
238
[    0.158980] msm_rpm_init: RPM firmware 3.0.16842958
239
[    0.173203] pm8018_probe: PMIC revision 1: F3
240
[    0.173233] pm8018_probe: PMIC revision 2: 08
241
[    0.173233] pm8018_probe: PMIC version: PM8018 rev 2.1
242
[    0.173264] pm8018_probe: PMIC Restart Reason: Triggered from KPD (power key press)
243
[    0.174240] pm_gpio_probe: OK: base=88, ngpio=6
244
[    0.174515] pm8xxx_mpp_probe: OK: base=94, ngpio=6
245
[    0.181962] cpufreq_table_init: CPU: 4 scaling frequencies supported.
246
[    0.186754] sps:REVISION of BAM 0xc6818000 is 0x5.
247
[    0.186784] sps:BAM 0x12244000 is registered.
248
[    0.187517] sps:sps is ready.
249
[    0.209034] bio: create slab <bio-0> at 0
250
[    0.209797] ION heap vmalloc created
251
[    0.209827] ION heap iommu created
252
[    0.209858] ION heap audio created at 46e01000 with size af000
253
[    0.210254] pm8xxx_pwm_probe: OK
254
[    0.210865] SCSI subsystem initialized
255
[    0.211048] usbcore: registered new interface driver usbfs
256
[    0.211200] usbcore: registered new interface driver hub
257
[    0.211414] usbcore: registered new device driver usb
258
[    0.212055] Registered led device: led:kb
259
[    0.212452] Advanced Linux Sound Architecture Driver Version 1.0.24.
260
[    0.213215] Switching to clocksource gp_timer
261
[    0.223134] NET: Registered protocol family 2
262
[    0.223378] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
263
[    0.223683] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
264
[    0.223744] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
265
[    0.223805] TCP: Hash tables configured (established 2048 bind 2048)
266
[    0.223836] TCP reno registered
267
[    0.223836] UDP hash table entries: 256 (order: 0, 4096 bytes)
268
[    0.223897] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
269
[    0.224629] NET: Registered protocol family 1
270
[    0.228231] Notify: smsm init
271
[    0.234518] NET: Registered protocol family 27
272
[    0.235373] apr_tal:Q6 Is Up
273
[    0.236593] modem_8960_init: modem fatal driver init'ed.
274
[    0.236868] lpass_fatal_init: lpass SSR driver init'ed.
275
[    0.237265] msm_rpm_log_probe: OK
276
[    0.249992] yaffs: yaffs built Jul 21 2016 14:54:39 Installing.
277
[    0.250053] msgmni has been set to 57
278
[    0.251701] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
279
[    0.251732] io scheduler noop registered
280
[    0.251762] io scheduler deadline registered
281
[    0.251823] io scheduler cfq registered (default)
282
[    0.398596] apr_tal:Modem Is Up
283
[    0.409064] msm_serial: driver initialized
284
[    0.409217] msm_serial_hsl: detected port #0
285
[    0.409400] msm_serial_hsl.0: ttyHSL0 at MMIO 0x16240000 (irq = 182) is a MSM
286
[    0.409522] msm_serial_hsl: console setup on port #0
287
[    0.834030] console [ttyHSL0] enabled
288
[    0.853807] msm_serial_hsl: driver initialized
289
[    0.865649] brd: module loaded
290
[    0.871600] loop: module loaded
291
[    0.874347] init gpio to irq = 0
292
[    0.877002] init gpio to irq = 312
293
[    0.880329] quectel_power_manager_probe: OK ###############################
294
[    0.973874] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
295
[    0.979490] qup_i2c qup_i2c.0: I2C slave addr:0xd not connected
296
[    0.985533] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
297
[    0.991973] qup_i2c qup_i2c.0: I2C slave addr:0xd not connected
298
[    0.997894] failed to read wcd9xxx register
299
[    1.002044] tabla-i2c-core 0-000d: Codec read failed
300
[    1.006989] failed to read the wcd9xxx status
301
[    1.014649] tabla-i2c-core: probe of 0-000d failed with error -107
302
[    1.019807] probe for other slaves devices of tabla
303
[    1.024690] probe for other slaves devices of tabla
304
[    1.029513] probe for other slaves devices of tabla
305
[    1.034457] i2c-core: driver [tabla-i2c-core] using legacy suspend method
306
[    1.041141] i2c-core: driver [tabla-i2c-core] using legacy resume method
307
[    1.049137] SCSI Media Changer driver v0.25 
308
[    1.053197] msm_nand_probe: phys addr 0x1b400000 
309
[    1.057134] msm_nand_probe: dmac 0x3
310
[    1.060643] msm_nand_probe: allocated dma buffer at ffdfe000, dma_addr 46a40000
311
[    1.068121] ONFI probe : Found a nonONFI Compliant device 
312
[    1.073462] status: c00020
313
[    1.076087] nandid: 1590aac8 maker c8 device aa
314
[    1.080604] Found a supported NAND device
315
[    1.084602] NAND Controller ID : 0x4030
316
[    1.088386] NAND Device ID  : 0x1590aac8
317
[    1.092293] Buswidth : 8 Bits
318
[    1.095284] Density  : 256 MByte
319
[    1.098458] Pagesize : 2048 Bytes
320
[    1.101754] Erasesize: 131072 Bytes
321
[    1.105264] Oobsize  : 64 Bytes
322
[    1.108377] CFG0 Init  : 0xa8d408c0
323
[    1.111826] CFG1 Init  : 0x0004745c
324
[    1.115336] ECCBUFCFG  : 0x00000203
325
[    1.118785] Creating 16 MTD partitions on "msm_nand":
326
[    1.123851] 0x0000050c0000-0x000005b00000 : "boot"
327
[    1.130260] 0x000000140000-0x0000004a0000 : "sbl2"
328
[    1.135479] 0x0000004a0000-0x000000800000 : "rpm"
329
[    1.140485] 0x000000800000-0x000000d80000 : "efs2"
330
[    1.145643] 0x000000d80000-0x0000012e0000 : "dsp1"
331
[    1.150770] 0x0000012e0000-0x000001d20000 : "dsp3"
332
[    1.156020] 0x000001d20000-0x000004fe0000 : "dsp2"
333
[    1.161147] 0x000004fe0000-0x0000050c0000 : "aboot"
334
[    1.166366] 0x000000000000-0x000000140000 : "mibib"
335
[    1.171493] 0x000005b00000-0x000009b60000 : "cache"
336
[    1.176773] 0x000009b60000-0x000009cc0000 : "misc"
337
[    1.181840] 0x000009cc0000-0x00000a720000 : "recovery"
338
[    1.187395] 0x00000a720000-0x00000a880000 : "fota"
339
[    1.192614] 0x00000a880000-0x00000bf60000 : "recoveryfs"
340
[    1.198382] 0x00000bf60000-0x00000d640000 : "system"
341
[    1.203754] 0x00000d640000-0x000010000000 : "userdata"
342
[    1.210407] rmnet_init: BAM devices[8]
343
[    1.218373] msm_otg msm_otg: msm_otg probe
344
[    1.221455] msm_otg msm_otg: failed to get phy_clk
345
[    1.226308] msm_otg msm_otg: OTG regs = c6828000
346
[    1.232595] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
347
[    1.251121] Initializing USB Mass Storage driver...
348
[    1.255211] usbcore: registered new interface driver usb-storage
349
[    1.260949] USB Mass Storage support registered.
350
[    1.265679] usbcore: registered new interface driver ums-alauda
351
[    1.271570] usbcore: registered new interface driver ums-cypress
352
[    1.277552] usbcore: registered new interface driver ums-datafab
353
[    1.283503] usbcore: registered new interface driver ums-freecom
354
[    1.289516] usbcore: registered new interface driver ums-isd200
355
[    1.295406] usbcore: registered new interface driver ums-jumpshot
356
[    1.301480] usbcore: registered new interface driver ums-karma
357
[    1.307309] usbcore: registered new interface driver ums-onetouch
358
[    1.313352] usbcore: registered new interface driver ums-sddr09
359
[    1.319304] usbcore: registered new interface driver ums-sddr55
360
[    1.325194] usbcore: registered new interface driver ums-usbat
361
[    1.330993] usbcore: registered new interface driver usb_ehset_test
362
[    1.337494] msm_hsic_peripheral msm_hsic_peripheral: HSIC Peripheral regs = c682a000
363
[    1.357912] msm_otg msm_otg: phy_reset: success
364
[    1.362368] msm_hsusb msm_hsusb: [ci13xxx_start] hw_ep_max = 32
365
[    1.367678] mbim_init: initialize 1 instances
366
[    1.372287] mbim_init: Initialized 1 ports
367
[    1.379429] rndis_qc_init: initialize rndis QC instance
368
[    1.384343] android_usb gadget: Mass Storage Function, version: 2009/09/11
369
[    1.390477] android_usb gadget: Number of LUNs=1
370
[    1.395147]  lun0: LUN: removable file: (no medium)
371
[    1.400457] android_usb gadget: android_usb ready
372
[    1.405005] msm_hsic_peripheral msm_hsic_peripheral: [ci13xxx_start] hw_ep_max = 32
373
[    1.412452] android_usb gadget: android_usb ready
374
[    1.417030] msm_hsic_peripheral msm_hsic_peripheral: CI13XXX_CONTROLLER_RESET_EVENT received
375
[    1.425423] msm_hsic_peripheral msm_hsic_peripheral: CI13XXX_CONTROLLER_UDC_STARTED_EVENT received
376
[    1.436105] android_work: android_work:usb disconnect cause suspended&sw_suspended to 0
377
[    1.443094] android_work: android_work: did not send uevent (0 0   (null))
378
[    1.450083] msm_hsic_peripheral msm_hsic_peripheral: HSIC-USB in low power mode
379
[    1.464764] couldn't get usb power supply
380
[    1.468976] diagchar initialized now
381
[    1.471814] input: pmic8xxx_pwrkey as /devices/platform/msm_ssbi.0/pm8018-core/pm8xxx-pwrkey/input/input0
382
[    1.485365] diag: Invalid Msg type 12 proc 2
383
[    1.505631] rtc-pm8xxx rtc-pm8xxx: rtc core: registered pm8xxx_rtc as rtc0
384
[    1.511948] i2c /dev entries driver
385
[    1.518480] pm8xxx_adc_probe: failed to request pa_therm vreg with error -19
386
[    1.545551] pm8xxx_tm_probe: OK
387
[    1.547932] cpuidle: using governor ladder
388
[    1.551747] cpuidle: using governor menu
389
[    1.556508] mmc0: mci-version: 18
390
[    1.560048] mmc0: bam physical base=0x12182000
391
[    1.563467] mmc0: bam virtual base=0xc6830000
392
[    1.567892] sps:BAM 0x12182000 is registered.
393
[    1.571982] mmc0: BAM device registered. bam_handle=0xc63c5000
394
[    1.578116] sps:REVISION of BAM 0xc6830000 is 0x5.
395
[    1.583335] mmc0: Qualcomm MSM SDCC-BAM at 0x0000000012182000 irq 130
396
[    1.589195] mmc0: Qualcomm MSM SDCC-DML at 0x0000000012180800
397
[    1.597405] mmc0: Qualcomm MSM SDCC-core at 0x0000000012180000 irq 136,368 dma -1 dmacrcri -1
398
[    1.606439] mmc0: 8 bit data mode disabled
399
[    1.609674] mmc0: 4 bit data mode enabled
400
[    1.613490] mmc0: polling status mode disabled
401
[    1.618098] mmc0: MMC clock 400000 -> 48000000 Hz, PCLK 0 Hz
402
[    1.624324] mmc0: Slot eject status = 0
403
[    1.627376] mmc0: Power save feature enable = 1
404
[    1.631893] mmc0: SPS-BAM data transfer mode available
405
[    1.637295] mmc1: mci-version: 18
406
[    1.645383] mmc1: bam physical base=0x12142000
407
[    1.654753] mmc1: bam virtual base=0xc686c000
408
[    1.660125] sps:BAM 0x12142000 is registered.
409
[    1.668243] mmc1: BAM device registered. bam_handle=0xc581b200
410
[    1.678284] sps:REVISION of BAM 0xc686c000 is 0x5.
411
[    1.692659] mmc1: Qualcomm MSM SDCC-BAM at 0x0000000012142000 irq 129
412
[    1.703067] mmc1: Qualcomm MSM SDCC-DML at 0x0000000012140800
413
[    1.712955] mmc1: No card detect facilities available
414
[    1.722295] mmc1: Qualcomm MSM SDCC-core at 0x0000000012140000 irq 135,0 dma -1 dmacrcri -1
415
[    1.734594] mmc1: 8 bit data mode disabled
416
[    1.742591] mmc1: 4 bit data mode enabled
417
[    1.750556] mmc1: polling status mode disabled
418
[    1.754616] mmc1: MMC clock 400000 -> 48000000 Hz, PCLK 0 Hz
419
[    1.759682] mmc1: Slot eject status = 0
420
[    1.763497] mmc1: Power save feature enable = 1
421
[    1.767984] mmc1: SPS-BAM data transfer mode available
422
[    1.774484] logger: created 256K log 'log_main'
423
[    1.778330] logger: created 256K log 'log_events'
424
[    1.782908] logger: created 256K log 'log_radio'
425
[    1.787669] logger: created 256K log 'log_system'
426
[    1.842575] voice_allocate_shared_memory: ION memory allocation failed
427
[    1.853502] msm_pcm_probe: dev name msm-voip-dsp
428
[    1.868213] msm_pcm_probe: dev name msm-host-pcm-voice
429
[    1.873340] msm_pcm_probe: dev name msm-pcm-dsp
430
[    1.877033] msm_pcm_probe: dev name msm-multi-ch-pcm-dsp
431
[    1.883198] mdm9615_audio_init: Interface Type = -1
432
[    1.887868] ALSA device list:
433
[    1.890126]   No soundcards found.
434
[    1.893392] Netfilter messages via NETLINK v0.30.
435
[    1.898214] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
436
[    1.904959] ip_set: protocol 6
437
[    1.907187] ip_tables: (C) 2000-2006 Netfilter Core Team
438
[    1.912620] TCP cubic registered
439
[    1.916954] NET: Registered protocol family 10
440
[    1.923332] ip6_tables: (C) 2000-2006 Netfilter Core Team
441
[    1.928094] NET: Registered protocol family 17
442
[    1.932153] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
443
[    1.939783] Registering SWP/SWPB emulation handler
444
[    1.947840] clock_late_init() disabled 42 unused clocks
445
[    1.955989] MSM Watchdog Initialized
446
[    1.958828] no pmic restart interrupt specified
447
[    1.964932] rtc-pm8xxx rtc-pm8xxx: setting system clock to 1970-01-01 00:34:05 UTC (2045)
448
[    1.973172] yaffs: dev is 32505870 name is "mtdblock14" rw
449
[    1.977689] yaffs: passed flags ""
450
[    1.981016] yaffs: Attempting MTD mount of 31.14,"mtdblock14"
451
[    2.039401] yaffs: block 155 is bad
452
[    2.099435] sps:BAM 0x124c2000 is registered.
453
[    2.144208] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_RESET_EVENT received
454
[    3.018037] yaffs: yaffs_read_super: is_checkpointed 0
455
[    3.018129] VFS: Mounted root (yaffs2 filesystem) on device 31:14.
456
[    3.023805] Freeing init memory: 168K
457
[    3.319090] sps:BAM 0x12502000 is registered.
458
[    3.325194] enable_store: android_usb: already disabled
459
[    3.334014] usmd:register_sysctl_table success.
460
[    3.337982] frmnet_bind: RmNet(0) dual Speed, IN:ep8in OUT:ep5out
461
[    3.545734] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
462
[    3.551258] android_work: android_work:usb disconnect cause suspended&sw_suspended to 0
463
[    3.564596] android_work: android_work: did not send uevent (0 0   (null))
464
[    3.619960] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
465
[    3.625911] android_work: android_work: sent uevent USB_STATE=CONNECTED
466
[    3.631893] android_work: android_work:usb disconnect cause suspended&sw_suspended to 0
467
[    3.655241] android_work: android_work: sent uevent USB_STATE=DISCONNECTED
468
[    3.726629] android_usb gadget: high speed config #1: android_usb
469
[    3.731848] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
470
[    3.738013] msm_otg msm_otg: Avail curr from USB = 500
471
[    3.743293] diag: USB connected
472
[    3.744575] sps:REVISION of BAM 0xc68b8000 is 0x5.
473
[    3.749855] android_work: android_work: sent uevent USB_STATE=CONNECTED
474
[    3.776468] diag: USB connected
475
[    3.834976] android_work: android_work: sent uevent USB_STATE=CONFIGURED
476
[    6.987578] yaffs: dev is 32505871 name is "mtdblock15" rw
477
[    6.992034] yaffs: passed flags ""
478
[    6.995513] yaffs: Attempting MTD mount of 31.15,"mtdblock15"
479
[    8.647001] yaffs: yaffs_read_super: is_checkpointed 0
480
[    8.682405] yaffs: dev is 32505865 name is "mtdblock9" rw
481
[    8.686983] yaffs: passed flags ""
482
[    8.690187] yaffs: Attempting MTD mount of 31.9,"mtdblock9"
483
[    8.692507] yaffs: yaffs_read_super: is_checkpointed 1
484
[    8.984709] adb_open
485
[    9.579856] yaffs: dev is 32505869 name is "mtdblock13" rw
486
[    9.590325] yaffs: passed flags ""
487
[    9.597192] yaffs: Attempting MTD mount of 31.13,"mtdblock13"
488
[    9.597222] yaffs: auto selecting yaffs2
489
[    9.676789] yaffs: yaffs_read_super: is_checkpointed 1
490
[    9.955012] mbim_open: Open mbim driver
491
[    9.959957] mbim_open: Lock mbim_dev->open_excl for open
492
[    9.971738] mbim_open: USB cable not connected
493
[    9.975553] mbim_open: Exit, mbim file opened
494
[   10.053410] smd_pkt_open: DATA9_CNTL open failed -19
495
[   10.085731] smd_pkt_open: DATA12_CNTL open failed -19
496
[   10.127941] smd_pkt_open: DATA13_CNTL open failed -19
497
[   10.175919] smd_pkt_open: DATA14_CNTL open failed -19
498
[   10.805707] qsmem_poll_timer_cb:67 Modem Msg received.
499
[   10.860521] nmea: smd opened
500
[   11.087746] dtr_smd_open smd_open_ret = 0(0 SUCCESS)
501
[   11.091744] DTR SMD EVENT OPEN
502
[   11.113016] buf:dtr_low-
503
[   11.115000] enter rt5616_modinit
504
[   11.125316] enter rt5616_i2c_probe
505
[   11.135571] enter rt5616_probe
506
[   11.137982] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1300c8, irq:183
507
[   11.144239] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
508
[   11.150404] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
509
[   11.156874] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
510
[   11.178391] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1300c8, irq:183
511
[   11.184098] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
512
[   11.193010] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
513
[   11.198687] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
514
[   11.204761] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
515
[   11.211597] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
516
[   11.217610] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
517
[   11.224019] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
518
[   11.230154] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
519
[   11.236593] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
520
[   11.242697] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
521
[   11.249290] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
522
[   11.255241] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
523
[   11.261742] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
524
[   11.267938] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
525
[   11.274408] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
526
[   11.280482] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
527
[   11.286952] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
528
[   11.292995] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
529
[   11.299496] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
530
[   11.305569] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
531
[   11.312314] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
532
[   11.318663] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
533
[   11.327697] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
534
[   11.333801] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
535
[   11.343567] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
536
[   11.349641] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
537
[   11.356111] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
538
[   11.362185] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
539
[   11.368655] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
540
[   11.374790] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
541
[   11.381291] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
542
[   11.387456] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
543
[   11.393834] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
544
[   11.400244] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
545
[   11.407172] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
546
[   11.413215] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
547
[   11.420845] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
548
[   11.426552] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
549
[   11.432992] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
550
[   11.439127] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
551
[   11.445566] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
552
[   11.451854] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
553
[   11.458263] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
554
[   11.464306] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
555
[   11.470746] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
556
[   11.476911] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
557
[   11.483351] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
558
[   11.489485] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
559
[   11.495925] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
560
[   11.501999] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
561
[   11.509720] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
562
[   11.514939] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
563
[   11.521471] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
564
[   11.527575] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
565
[   11.534472] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
566
[   11.540088] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
567
[   11.546864] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
568
[   11.552662] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
569
[   11.559133] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
570
[   11.565206] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
571
[   11.571799] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
572
[   11.577872] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
573
[   11.585502] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
574
[   11.590813] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
575
[   11.597192] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
576
[   11.603235] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
577
[   11.610102] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
578
[   11.616023] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
579
[   11.622524] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
580
[   11.628536] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
581
[   11.634945] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
582
[   11.641049] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
583
[   11.647489] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
584
[   11.657652] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
585
[   11.663268] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
586
[   11.670318] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
587
[   11.676697] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
588
[   11.682191] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
589
[   11.688661] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
590
[   11.694674] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
591
[   11.701327] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
592
[   11.707279] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
593
[   11.713902] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
594
[   11.719945] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
595
[   11.726323] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
596
[   11.732427] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
597
[   11.738989] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
598
[   11.744971] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
599
[   11.751838] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
600
[   11.757698] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
601
[   11.764169] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
602
[   11.770242] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
603
[   11.776743] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
604
[   11.782786] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
605
[   11.789317] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
606
[   11.795360] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
607
[   11.802105] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
608
[   11.808026] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
609
[   11.814497] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
610
[   11.820570] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
611
[   11.827102] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
612
[   11.833114] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
613
[   11.839676] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
614
[   11.845688] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
615
[   11.852372] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
616
[   11.858354] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
617
[   11.866809] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
618
[   11.872028] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
619
[   11.878498] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
620
[   11.884541] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
621
[   11.891103] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
622
[   11.897146] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
623
[   11.903555] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
624
[   11.909720] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
625
[   11.916191] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
626
[   11.922264] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
627
[   11.928795] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
628
[   11.934839] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
629
[   11.941339] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
630
[   11.947474] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
631
[   11.953914] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
632
[   11.960476] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
633
[   11.966519] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
634
[   11.972592] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
635
[   11.979093] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
636
[   11.985228] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
637
[   11.991698] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
638
[   11.997833] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
639
[   12.004272] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
640
[   12.010407] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
641
[   12.016847] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
642
[   12.022951] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
643
[   12.029452] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
644
[   12.035525] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
645
[   12.042026] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
646
[   12.048161] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
647
[   12.054600] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
648
[   12.061254] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
649
[   12.067266] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
650
[   12.073370] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
651
[   12.079993] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
652
[   12.085945] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1343c8, irq:183
653
[   12.092385] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
654
[   12.098550] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
655
[   12.104959] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
656
[   12.111246] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
657
[   12.117564] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
658
[   12.123638] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
659
[   12.130138] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
660
[   12.136273] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
661
[   12.142713] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
662
[   12.148878] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
663
[   12.155318] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
664
[   12.161452] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
665
[   12.167892] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
666
[   12.173996] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
667
[   12.180894] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
668
[   12.187120] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
669
[   12.193071] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
670
[   12.199206] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
671
[   12.205646] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
672
[   12.213032] msm_dai_q6_dai_sec_auxpcm_probe
673
[   12.216297] msm_dai_q6_dai_sec_auxpcm_probe
674
[   12.224629] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1300c8, irq:183
675
[   12.230276] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
676
[   12.236441] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
677
[   12.242820] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
678
[   12.248985] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
679
[   12.255424] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
680
[   12.261559] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
681
[   12.267999] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
682
[   12.274103] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
683
[   12.280604] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
684
[   12.286769] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
685
[   12.293178] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
686
[   12.299313] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
687
[   12.305753] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
688
[   12.311918] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
689
[   12.318358] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
690
[   12.324431] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
691
[   12.330932] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
692
[   12.337066] qup_i2c qup_i2c.0: QUP: I2C status flags :0x1363c8, irq:183
693
[   12.343537] qup_i2c qup_i2c.0: I2C slave addr:0x1b not connected
694
[   12.349916] asoc: null-codec-dai <-> MultiMedia1 mapping ok
695
[   12.357698] asoc: null-codec-dai <-> MultiMedia2 mapping ok
696
[   12.364748] asoc: null-codec-dai <-> CS-VOICE mapping ok
697
[   12.372012] asoc: null-codec-dai <-> VoIP mapping ok
698
[   12.378666] asoc: null-codec-dai <-> SLIMBUS0_HOSTLESS mapping ok
699
[   12.386235] asoc: msm-stub-rx <-> msm-dai-q6.241 mapping ok
700
[   12.393285] asoc: msm-stub-tx <-> msm-dai-q6.240 mapping ok
701
[   12.400396] asoc: null-codec-dai <-> AUXPCM_HOSTLESS mapping ok
702
[   12.407843] asoc: null-codec-dai <-> VoLTE mapping ok
703
[   12.414375] asoc: null-codec-dai <-> DTMF_RX_HOSTLESS mapping ok
704
[   12.421822] asoc: msm-stub-tx <-> msm-dai-stub mapping ok
705
[   12.428658] asoc: msm-stub-tx <-> msm-dai-stub mapping ok
706
[   12.435464] asoc: msm-stub-rx <-> msm-dai-stub mapping ok
707
[   12.442301] asoc: msm-stub-tx <-> msm-dai-stub mapping ok
708
[   12.449107] asoc: msm-stub-rx <-> msm-dai-stub mapping ok
709
[   12.456096] asoc: msm-stub-rx <-> msm-dai-q6.12288 mapping ok
710
[   12.463238] asoc: msm-stub-tx <-> msm-dai-q6.12289 mapping ok
711
[   12.470441] asoc: msm-stub-rx <-> msm-dai-q6.224 mapping ok
712
[   12.477460] asoc: msm-stub-tx <-> msm-dai-q6.225 mapping ok
713
[   12.484541] asoc: rt5616-aif1 <-> msm-dai-q6.2 mapping ok
714
[   12.491530] asoc: rt5616-aif1 <-> msm-dai-q6.3 mapping ok
715
[   12.498397] asoc: msm-stub-rx <-> msm-dai-q6.12 mapping ok
716
[   12.505264] asoc: msm-stub-tx <-> msm-dai-q6.13 mapping ok
717
[   12.512223] asoc: msm-stub-rx <-> msm-dai-q6.32773 mapping ok
718
[   12.519395] asoc: msm-stub-tx <-> msm-dai-q6.32772 mapping ok
719
[   12.526598] asoc: msm-stub-tx <-> msm-dai-q6.32771 mapping ok
720
-   47.270715] buf:+QFOPEN  passwd 
721
-  104.919975] buf:+QFCLOSE 0
722
-  121.510392] buf:+QFOPEN ?
723
[  391.714603] sps:BAM is already registered: 12502000
724
[  391.718571] usb_bam_init: register bam error -17
725
[  391.723088] usb_bam usb_bam: failed to initialize usb bam
726
[  391.728887] diag: USB disconnected
727
[  391.731603] frmnet_bind: RmNet(0) dual Speed, IN:ep13in OUT:ep7out
728
[  391.737158] sps:sps_device_reset:device handle should not be 0.
729
[  391.746009] usb_bam_reset: BAM reset failed
730
[  391.755959] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
731
[  391.761269] msm_otg msm_otg: Avail curr from USB = 2
732
[  391.766213] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_SUSPEND_EVENT received
733
[  391.773264] android_work: android_work: did not send uevent (1 1   (null))
734
[  392.126384] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_RESUME_EVENT received
735
[  392.132305] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
736
[  392.138562] msm_otg msm_otg: Avail curr from USB = 0
737
[  392.144025] android_work: android_work:usb disconnect cause suspended&sw_suspended to 0
738
[  392.155409] android_work: android_work: sent uevent USB_STATE=DISCONNECTED
739
[  392.198687] android_work: android_work: sent uevent USB_STATE=CONNECTED
740
[  392.204578] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
741
[  392.216145] android_work: android_work:usb disconnect cause suspended&sw_suspended to 0
742
[  392.235678] android_work: android_work: sent uevent USB_STATE=DISCONNECTED
743
[  392.291957] android_usb gadget: high speed config #1: android_usb
744
[  392.298214] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
745
[  392.303586] msm_otg msm_otg: Avail curr from USB = 500
746
[  392.309110] diag: USB connected
747
[  392.315366] android_work: android_work: sent uevent USB_STATE=CONNECTED
748
[  392.341492] diag: USB connected
749
[  392.387700] android_work: android_work: sent uevent USB_STATE=CONFIGURED
750
[  436.916496] sps:BAM is already registered: 12502000
751
[  436.920158] usb_bam_init: register bam error -17
752
[  436.925041] usb_bam usb_bam: failed to initialize usb bam
753
[  436.930749] diag: USB disconnected
754
[  436.933221] adb_bind_config
755
[  436.935144] sps:sps_device_reset:device handle should not be 0.
756
[  436.945307] frmnet_bind: RmNet(0) dual Speed, IN:ep14in OUT:ep8out
757
[  436.950617] usb_bam_reset: BAM reset failed
758
[  436.960750] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
759
[  436.966091] msm_otg msm_otg: Avail curr from USB = 2
760
[  436.971036] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_SUSPEND_EVENT received
761
[  436.978055] android_work: android_work: did not send uevent (1 1   (null))
762
[  437.171158] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_RESUME_EVENT received
763
[  437.177079] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
764
[  437.183335] msm_otg msm_otg: Avail curr from USB = 0
765
[  437.188768] android_work: android_work:usb disconnect cause suspended&sw_suspended to 0
766
[  437.198168] android_work: android_work: sent uevent USB_STATE=DISCONNECTED
767
[  437.243644] android_work: android_work: sent uevent USB_STATE=CONNECTED
768
[  437.249565] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
769
[  437.260491] android_work: android_work:usb disconnect cause suspended&sw_suspended to 0
770
[  437.279078] android_work: android_work: sent uevent USB_STATE=DISCONNECTED
771
[  437.336578] android_usb gadget: high speed config #1: android_usb
772
[  437.342713] msm_otg msm_otg: Failed notifying 1 charger type to PMIC
773
[  437.348115] msm_otg msm_otg: Avail curr from USB = 500
774
[  437.353670] diag: USB connected
775
[  437.354768] msm_hsusb msm_hsusb: [ep_enable] enabling a non-empty endpoint!
776
[  437.363741] android_work: android_work: sent uevent USB_STATE=CONNECTED
777
[  437.437540] android_work: android_work: sent uevent USB_STATE=CONFIGURED
778
[  728.231893] [dsp_debug.c:dsp_read] Memory Invalid or not initialized, Base = 0x0, size = 0x0
779
[  748.249992] Ramdump(ramdump_smem-modem): Read when there's no dump available!
780 1 zecke
[  754.749549] Ramdump(ramdump_modem_sw): Read when there's no dump available!
781 4 zecke
</pre>
Add picture from clipboard (Maximum size: 48.8 MB)