Project

General

Profile

Rtl-sdr » History » Version 178

steve-m, 02/19/2016 10:51 PM
add gr-rds

1 1 steve-m
[[PageOutline]]
2
= rtl-sdr =
3
4 167 steve-m
DVB-T dongles based on the Realtek RTL2832U can be used as a cheap SDR, since the chip allows transferring the raw I/Q samples to the host, which is officially used for DAB/DAB+/FM demodulation. The possibility of this has been discovered by Eric Fry ([http://rtlsdr.org/#history_and_discovery_of_rtlsdr History and Discovery of RTLSDR]). Antti Palosaari has not been involved in development of rtl-sdr.
5 1 steve-m
6
== Specifications ==
7
8 172 steve-m
The RTL2832U outputs 8-bit I/Q-samples, and the highest theoretically possible sample-rate is 3.2 MS/s, however, the highest sample-rate without lost samples that has been tested so far is 2.56 MS/s. The frequency range is highly dependent of the used tuner, '''dongles that use the Elonics E4000 offer the widest possible range (see table below)'''.
9 1 steve-m
10 136 steve-m
||'''Tuner'''||'''Frequency range'''||
11 159 sls777
||Elonics E4000||52 - 2200 MHz with a gap from 1100 MHz to 1250 MHz (varies)||
12 136 steve-m
||Rafael Micro R820T||24 - 1766 MHz||
13 175 steve-m
||Rafael Micro R828D||24 - 1766 MHz||
14 136 steve-m
||Fitipower FC0013||22 - 1100 MHz (FC0013B/C, FC0013G has a separate L-band input, which is unconnected on most sticks)||
15
||Fitipower FC0012||22 - 948.6 MHz||
16
||FCI FC2580||146 - 308 MHz and 438 - 924 MHz (gap in between)||
17
18 1 steve-m
== Supported Hardware ==
19
20 141 steve-m
'''Note:''' Many devices with EEPROM have 0x2838 as PID and RTL2838 as product name, but in fact all of them have an RTL2832U inside.[[br]]
21
Realtek never released a chip marked as RTL2838 so far.[[br]][[br]]
22 45 horiz0n
The following devices are known to work fine with RTLSDR software:
23 1 steve-m
24 43 steve-m
||'''VID'''||'''PID'''||'''tuner'''||'''device name'''||
25 42 Hoernchen
||0x0bda||0x2832||all of them||Generic RTL2832U (e.g. hama nano)||
26
||0x0bda||0x2838||E4000||ezcap USB 2.0 DVB-T/DAB/FM dongle||
27
||0x0ccd||0x00a9||FC0012||Terratec Cinergy T Stick Black (rev 1)||
28 49 Hoernchen
||0x0ccd||0x00b3||FC0013||Terratec NOXON DAB/DAB+ USB dongle (rev 1)||
29 42 Hoernchen
||0x0ccd||0x00d3||E4000||Terratec Cinergy T Stick RC (Rev.3)||
30
||0x0ccd||0x00e0||E4000||Terratec NOXON DAB/DAB+ USB dongle (rev 2)||
31
||0x185b||0x0620||E4000||Compro Videomate U620F||
32
||0x185b||0x0650||E4000||Compro Videomate U650F||
33
||0x1f4d||0xb803||FC0012||GTek T803||
34
||0x1f4d||0xc803||FC0012||Lifeview LV5TDeluxe||
35
||0x1b80||0xd3a4||FC0013||Twintech UT-40||
36
||0x1d19||0x1101||FC2580||Dexatek DK DVB-T Dongle (Logilink VG0002A)||
37
||0x1d19||0x1102||?||Dexatek DK DVB-T Dongle (MSI DigiVox mini II V3.0)||
38
||0x1d19||0x1103||FC2580||Dexatek Technology Ltd. DK 5217 DVB-T Dongle||
39
||0x0458||0x707f||?||Genius TVGo DVB-T03 USB dongle (Ver. B)||
40
||0x1b80||0xd393||FC0012||GIGABYTE GT-U7300||
41
||0x1b80||0xd394||?||DIKOM USB-DVBT HD||
42
||0x1b80||0xd395||FC0012||Peak 102569AGPK||
43
||0x1b80||0xd39d||FC0012||SVEON STV20 DVB-T USB & FM||
44 14 steve-m
45 31 horiz0n
People over at reddit [http://www.reddit.com/r/RTLSDR/comments/s6ddo/rtlsdr_compatibility_list_v2_work_in_progress/ are collecting a list (v2)] of other devices that are compatible.
46 2 steve-m
47 174 steve-m
If you find a device that is not yet in the device list but should be supported, please send the VID/PID and additional info (used tuner, device name) to our mailing list.
48 5 steve-m
49
This is the PCB of the ezcap-stick:[[br]][[br]]
50
[[Image(ezcap_top.jpg,50%)]][[br]]
51
More pictures can be found [http://www.steve-m.de/pictures/rtl-sdr/ here].
52 2 steve-m
53
== Software ==
54
55 157 sls777
Much software is available for the RTL2832. Most of the user-level packages rely on the librtlsdr library which comes as part of the rtl-sdr codebase. This codebase contains both the library itself and also a number of command line tools such as rtl_test, rtl_sdr, rtl_tcp, and rtl_fm. These command line tools use the library to test for the existence of RTL2832 devices and to perform basic data transfer functions to and from the device.
56 1 steve-m
57 157 sls777
Because most of the RTL2832 devices are connected using USB, the librtlsdr library depends on the libusb library to communicate with the device.
58
59
At the user level, there are several options for interacting with the hardware. The rtl-sdr codebase contains a basic FM receiver program that operates from the command line. The rtl_fm program is a command line tool that can initialize the RTL2832, tune to a given frequency, and output the received audio to a file or pipe the output to command line audio players such as the alsa aplay or the sox play commands. There is also the rtl_sdr program that will output the raw I-Q data to a file for more basic analysis.
60
61 158 sls777
For example, the following command will do reception of commercial wide-band FM signals:
62
63
{{{
64 1 steve-m
rtl_fm -f 96.3e6 -W -s 200000 -r 48000 - | aplay -r 48k -f S16_LE
65 159 sls777
}}}
66
67
On a Mac, a similar command that works is as follows. This assumes that the sox package is installed, 'port install sox':
68
69
{{{
70
rtl_fm -f 90100000 -W -s 200000 -r 48000 - | play -r 48000 -t s16 -L -c 1  -
71 158 sls777
}}}
72
73 157 sls777
If you want to do more advanced experiments, the GNU Radio collection of tools can be used to build custom radio devices. GNU Radio can be used both from a GUI perspective in which you can drag-and-drop radio components to build a radio and also programmatically where software programs written in C or Python are created that directly reference the internal GNU Radio functions.
74 158 sls777
75
The use of GNU Radio is attractive because of the large number of pre-built functions that can easily be connected together. However, be aware that this is a large body of software with dependencies on many libraries. Thankfully there is a simple script that will perform the installation but still, the time required can be on the order of hours. When starting out, it might be good to try the command line programs that come with the rtl-sdr package first and then install the GNU Radio system later.
76 157 sls777
77
The rtl-sdr code can be checked out with:
78 2 steve-m
{{{
79
git clone git://git.osmocom.org/rtl-sdr.git
80
}}}
81 35 horiz0n
82 172 steve-m
It can also be browsed via [http://cgit.osmocom.org/cgit/rtl-sdr/ cgit], and there's an official [https://github.com/steve-m/librtlsdr mirror on github] that also provides [https://github.com/steve-m/librtlsdr/releases packaged releases].
83 45 horiz0n
84 48 horiz0n
If you are going to "fork it on github" and enhance it, please contribute back and submit your patches to: osmocom-sdr at lists.osmocom.org
85 1 steve-m
86 177 steve-m
A [wiki:GrOsmoSDR GNU Radio source block] for [wiki:WikiStart OsmoSDR] '''and rtlsdr''' is available. '''Please install a recent gnuradio (>= v3.6.4) in order to be able to use it.''' 
87 41 horiz0n
88 131 laforge
=== Mailing List ===
89
90
We discuss both OsmoSDR as well as rtl-sdr on the following mailing list: [mailto:osmocom-sdr@lists.osmocom.org].
91
92
You can subscribe and/or unsubscribe via the following link: [http://lists.osmocom.org/mailman/listinfo/osmocom-sdr]
93
94 1 steve-m
=== Building the software ===
95
96 27 horiz0n
==== rtlsdr library & capture tool ====
97 1 steve-m
98 29 horiz0n
'''You have to install development packages for libusb1.0''' and can either use cmake or autotools to build the software.
99 27 horiz0n
100
Please note: prior pulling a new version from git and compiling it, please do a "make uninstall" first to properly remove the previous version.
101
102 19 steve-m
Building with cmake:
103
{{{
104 1 steve-m
cd rtl-sdr/
105 20 horiz0n
mkdir build
106
cd build
107
cmake ../
108 19 steve-m
make
109 33 steve-m
sudo make install
110 130 horiz0n
sudo ldconfig
111 19 steve-m
}}}
112
113 130 horiz0n
In order to be able to use the dongle as a non-root user, you may install the appropriate udev rules file by calling cmake with -DINSTALL_UDEV_RULES=ON argument in the above build steps.
114
{{{
115
cmake ../ -DINSTALL_UDEV_RULES=ON
116
}}}
117
118 19 steve-m
Building with autotools:
119
{{{
120
cd rtl-sdr/
121
autoreconf -i
122
./configure
123 33 steve-m
make
124 19 steve-m
sudo make install
125 130 horiz0n
sudo ldconfig
126 19 steve-m
}}}
127 1 steve-m
128 130 horiz0n
The built executables (rtl_sdr, rtl_tcp and rtl_test) can be found in rtl-sdr/src/.
129 1 steve-m
130 130 horiz0n
In order to be able to use the dongle as a non-root user, you may install the appropriate udev rules file by calling
131
{{{
132
sudo make install-udev-rules
133
}}}
134
135 169 Hoernchen
[attachment:RelWithDebInfo.zip pre-built Windows version]
136 72 horiz0n
137 1 steve-m
==== Gnuradio Source ====
138 27 horiz0n
139 164 horiz0n
'''The Gnu Radio source requires a recent gnuradio (>= v3.7 if building master branch or 3.6.5 when building gr3.6 branch) to be installed.'''
140 56 horiz0n
141 54 horiz0n
The source supports direct device operation as well as a tcp client mode when using the rtl_tcp utility as a spectrum server.
142 27 horiz0n
143
Please note: prior pulling a new version from git and compiling it, please do a "make uninstall" first to properly remove the previous version.
144 92 horiz0n
145 161 horiz0n
Please note: you always should build & '''install the latest version of the dependencies (librtlsdr in this case)''' before trying to build the gr source. The build system of gr-osmosdr will recognize them and enable specific source/sink components thereafter.
146 92 horiz0n
147 177 steve-m
Building with cmake (as described in the [wiki:GrOsmoSDR gr-osmosdr wiki page]):
148 161 horiz0n
149 27 horiz0n
{{{
150
git clone git://git.osmocom.org/gr-osmosdr
151 1 steve-m
cd gr-osmosdr/
152 164 horiz0n
}}}
153
154
If you are building for gnuradio 3.6 series, you have to switch to the gr3.6 branch as follows
155
{{{
156
git checkout gr3.6
157
}}}
158
159 166 horiz0n
then continue with
160
161 164 horiz0n
{{{
162 1 steve-m
mkdir build
163
cd build/
164
cmake ../
165 161 horiz0n
}}}
166
167
Now cmake should print out a summary of enabled/disabled components. You may disable certain components by following guidelines shown by cmake. Make sure the device of your interest is listed here. Check your dependencies and retry otherwise.
168
{{{
169
-- ######################################################
170
-- # gr-osmosdr enabled components                         
171
-- ######################################################
172
--   * Python support
173
--   * Osmocom IQ Imbalance Correction
174
--   * sysmocom OsmoSDR
175
--   * FunCube Dongle
176
--   * IQ File Source
177
--   * Osmocom RTLSDR
178
--   * RTLSDR TCP Client
179
--   * Ettus USRP Devices
180
--   * Osmocom MiriSDR
181
--   * HackRF Jawbreaker
182
-- 
183
-- ######################################################
184
-- # gr-osmosdr disabled components                        
185
-- ######################################################
186
-- 
187
-- Building for version: 4c101ea4 / 0.0.1git
188
-- Using install prefix: /usr/local
189
}}}
190
191
Now build & install
192 1 steve-m
{{{
193
make
194
sudo make install
195
sudo ldconfig
196
}}}
197
198 164 horiz0n
NOTE: The osmocom source block (osmocom/RTL-SDR Source) will appear under 'Sources' category in GRC menu.
199 1 steve-m
200 84 horiz0n
For initial tests we recommend the multimode receiver gnuradio companion flowgraph (see "Known Apps" table below).
201
202 104 horiz0n
You may find more detailed installation instructions in this recent [http://blog.opensecurityresearch.com/2012/06/getting-started-with-gnu-radio-and-rtl.html tutorial].
203 103 horiz0n
204 1 steve-m
==== Automated installation ====
205
206 101 horiz0n
Marcus D. Leech has kindly integrated the forementioned build steps into his gnuradio installation script at [http://www.sbrac.org/files/build-gnuradio]. This is the most user-friendly option so far.
207
208 1 steve-m
=== Usage ===
209
210 78 horiz0n
==== rtl_sdr ====
211
212 1 steve-m
Example: To tune to 392.0 MHz, and set the sample-rate to 1.8 MS/s, use:
213
214
{{{
215
./rtl_sdr /tmp/capture.bin -s 1.8e6 -f 392e6
216 74 horiz0n
}}}
217
218
to record samples to a file or to forward the data to a fifo.
219
220 90 horiz0n
If the device can't be opened, make sure you have the appropriate rights to access the device (install udev-rules from the repository, or run it as root).
221 74 horiz0n
222 78 horiz0n
==== rtl_tcp ====
223
224 80 horiz0n
Example:
225
226 1 steve-m
{{{
227 79 horiz0n
rtl_tcp -a 10.0.0.2 [-p listen port (default: 1234)]
228
Found 1 device(s).
229
Found Elonics E4000 tuner
230
Using Generic RTL2832U (e.g. hama nano)
231
Tuned to 100000000 Hz.
232
listening...
233
Use the device argument 'rtl_tcp=10.0.0.2:1234' in OsmoSDR (gr-osmosdr) source
234
to receive samples in GRC and control rtl_tcp parameters (frequency, gain, ...).
235 74 horiz0n
}}}
236 79 horiz0n
237 76 horiz0n
use the rtl_tcp=... device argument in gr-osmosdr source to receive the samples in GRC and control the rtl settings remotely.
238 1 steve-m
239 103 horiz0n
This application has been successfully crosscompiled for ARM and MIPS devices and is providing IQ data in a networked ADS-B setup at a rate of 2.4MSps. The gr-osmosdr source is being used together with an optimized gr-air-modes version (see Known Apps below).
240 163 steve-m
It is also available as a package in OpenWRT.
241 76 horiz0n
242 110 horiz0n
A use case is described [https://sites.google.com/site/embrtlsdr/ here].
243
244 1 steve-m
==== rtl_test ====
245 90 horiz0n
To check the possible tuning range (may heavily vary by some MHz depending on device and temperature), call
246 74 horiz0n
{{{
247
rtl_test -t
248 1 steve-m
}}}
249 90 horiz0n
250
To check the maximum samplerate possible on your machine, type (change the rate down until no sample loss occurs):
251 74 horiz0n
{{{
252
rtl_test -s 3.2e6
253 1 steve-m
}}}
254 90 horiz0n
A samplerate of 2.4e6 is known to work even over tcp connections (see rtl_tcp above). A sample rate of 2.88e6 may work without lost samples but this may depend on your PC/Laptop's host interface.
255 2 steve-m
256
== Using the data ==
257
258 3 steve-m
To convert the data to a standard cfile, following GNU Radio Block can be used:[[br]]
259
[[br]][[Image(rtl2832-cfile.png)]][[br]][[br]]
260 2 steve-m
The GNU Radio Companion flowgraph (rtl2832-cfile.grc) is attached to this page. It is based on the FM demodulation flowgraph posted by Alistair Buxton [http://thread.gmane.org/gmane.linux.drivers.video-input-infrastructure/44461/focus=44525 on this thread].
261 6 steve-m
262 22 horiz0n
Please note: for realtime operation you may use fifos (mkfifo) to forward the iq data from the capture utility to the GRC flowgraph.
263
264 115 horiz0n
You may use any of the the following gnuradio sources (they are equivalent):
265
[[br]][[br]][[Image(osmosource.png)]][[br]]
266
267 59 horiz0n
What has been successfully tested so far is the reception of [https://www.cgran.org/browser/projects/multimode/trunk Broadcast FM and air traffic AM] radio, [http://tetra.osmocom.org/ TETRA], [http://gmr.osmocom.org/ GMR], [http://svn.berlin.ccc.de/projects/airprobe/ GSM], [https://www.cgran.org/wiki/gr-air-modes ADS-B] and [https://github.com/smunaut/osmo-pocsag POCSAG].
268 32 horiz0n
269
Tell us your success story with other wireless protocols in ##rtlsdr channel on freenode IRC network.
270
271 61 horiz0n
== Known Apps ==
272 60 horiz0n
273 81 horiz0n
The following 3rd party applications and libraries are successfully using either librtlsdr directly or the corresponding gnuradio source (gr-osmosdr):
274 60 horiz0n
275
||'''Name'''||'''Type'''||'''Author'''||'''URL'''||
276 88 horiz0n
||gr-pocsag||GRC Flowgraph||Marcus Leech||[https://www.cgran.org/browser/projects/gr-pocsag/trunk]||
277 106 horiz0n
||multimode RX (try first!)||GRC Flowgraph||Marcus Leech||[https://www.cgran.org/browser/projects/multimode/trunk]||
278 89 steve-m
||simple_fm_rvc||GRC Flowgraph||Marcus Leech||[https://www.cgran.org/browser/projects/simple_fm_rcv/trunk]||
279 60 horiz0n
||python-librtlsdr||Python Wrapper||David Basden||[https://github.com/dbasden/python-librtlsdr]||
280 63 horiz0n
||pyrtlsdr||Python Wrapper||Roger||[https://github.com/roger-/pyrtlsdr]||
281 60 horiz0n
||rtlsdr-waterfall||Python FFT GUI||Kyle Keen||[https://github.com/keenerd/rtlsdr-waterfall]||
282 67 horiz0n
||Wireless Temp. Sensor RX||Gnuradio App||Kevin Mehall||[https://github.com/kevinmehall/rtlsdr-433m-sensor]||
283 1 steve-m
||!QtRadio||SDR GUI||Andrea Montefusco et al.||[http://napan.ca/ghpsdr3/index.php/RTL-SDR]||
284 171 steve-m
||gqrx||SDR GUI||Alexandru Csete||[https://github.com/csete/gqrx]||
285 116 horiz0n
||rtl_fm||SDR CLI||Kyle Keen||merged in librtlsdr master||
286 119 horiz0n
||SDR#||SDR GUI||Youssef Touil||[http://sdrsharp.com/] and [http://rtlsdr.org/softwarewindows Windows Guide] or [http://rtlsdr.org/softwarelinux Linux Guide]||
287 128 horiz0n
||tetra_demod_fft||Trunking RX||osmocom team||[http://cgit.osmocom.org/cgit/osmo-tetra/tree/src/demod/python/osmosdr-tetra_demod_fft.py osmosdr-tetra_demod_fft.py] and the [http://tetra.osmocom.org/trac/wiki/osmo-tetra#Quickexample HOWTO] ||
288
||airprobe||GSM sniffer||osmocom team et al||[http://git.gnumonks.org/cgi-bin/gitweb.cgi?p=airprobe.git]||
289
||gr-smartnet (WIP)||Trunking RX||Nick Foster||[http://www.reddit.com/r/RTLSDR/comments/us3yo/rtlsdr_smartnet/][[br]][http://www.reddit.com/r/RTLSDR/comments/vbxl0/attention_grsmartnet_users_or_attempted_users/ Notes from the author]||
290
||gr-air-modes||ADS-B RX||Nick Foster||[https://www.cgran.org/wiki/gr-air-modes] call with --rtlsdr option||
291
||Linrad||SDR GUI||Leif Asbrink (SM5BSZ)||[http://www.nitehawk.com/sm5bsz/linuxdsp/hware/rtlsdr/rtlsdr.htm][[br]]DAGC changes were applied to librtlsdr master||
292
||gr-ais (fork)||AIS RX||Nick Foster[[br]]Antoine Sirinelli[[br]]Christian Gagneraud||[https://github.com/chgans/gr-ais]||
293 137 horiz0n
||GNSS-SDR ||GPS RX (Realtime!)||Centre Tecnològic de[[br]]Telecomunicacions de Catalunya||[http://www.gnss-sdr.org/documentation/gnss-sdr-operation-realtek-rtl2832u-usb-dongle-dvb-t-receiver Documentation] and [http://www.gnss-sdr.org]||
294 145 steve-m
||LTE-Cell-Scanner ||LTE Scanner / Tracker||James Peroulas[[br]]Evrytania LLC||[http://www.evrytania.com/lte-tools][[br]][https://github.com/Evrytania/LTE-Cell-Scanner]||
295 146 horiz0n
||Simulink-RTL-SDR ||MATLAB/Simulink[[br]]wrapper||Michael Schwall[[br]]Sebastian Koslowski[[br]]Communication Engineering Lab (CEL)[[br]]Karlsruhe Institute of Technology (KIT)||[http://www.cel.kit.edu/simulink_rtl_sdr.php]||
296 145 steve-m
||gr-scan ||Scanner||techmeology||[http://www.techmeology.co.uk/gr-scan/]||
297 146 horiz0n
||kalibrate-rtl||calibration tool||Joshua Lackey[[br]]Alexander Chemeris[[br]]Steve Markgraf||[https://github.com/steve-m/kalibrate-rtl], [http://rtlsdr.org/files/kalibrate-win-release.zip Windows build]||
298
||pocsag-mrt||Multichannel Realtime[[br]]Decoder||iZsh||[https://github.com/iZsh/pocsag-mrt]||
299 152 horiz0n
||adsb# ||ADS-B RX||Youssef Touil[[br]]Ian Gilmour||[http://sdrsharp.com/index.php/a-simple-and-cheap-ads-b-receiver-using-rtl-sdr]||
300
||osmo-gmr-rtl||GMR1 RX||Dimitri Stolnikov||[http://gmr.osmocom.org/trac/wiki/GettingStarted#RTLSDRdongles]||
301
||rtl_adsb||ADS-B RX||Kyle Keen||comes with the library||
302
||dump1090||ADS-B RX||Salvatore Sanfilippo||[https://github.com/antirez/dump1090]||
303 153 horiz0n
||rtl_433||Temperature Sensor[[br]]Receiver||Benjamin Larsson||[https://github.com/merbanan/rtl_433]||
304
||randio||Random number generator||Michel Pelletier||[https://github.com/michelp/randio]||
305
||gr-wmbus||m-bus (EN 13757-4) RX||oWCTejLVlFyNztcBnOoh||[https://github.com/oWCTejLVlFyNztcBnOoh/gr-wmbus]||
306
||ec3k||EnergyCount 3000 RX||Tomaž Šolc||[https://github.com/avian2/ec3k]||
307 156 horiz0n
||RTLSDR-Scanner||Radio Scanner||EarToEarOak||[https://github.com/EarToEarOak/RTLSDR-Scanner]||
308 178 steve-m
||simple_ra||Radio Astronomy App||Marcus Leech||[https://cgran.org/wiki/simple_ra]||
309
||rtlizer||Spectrum analyzer||Alexandru Csete||[https://github.com/csete/rtlizer]||
310
||FS20_decode||FS20 Decoder||Thomas Frisch||[https://github.com/eT0M/rtl_sdr_FS20_decoder]||
311
||OpenLTE||LTE Toolkit||Ben Wojtowicz||[http://sourceforge.net/p/openlte/home/Home/]||
312
||rtltcpaccess||DAB compatibility layer||Steve Markgraf||[https://github.com/steve-m/rtltcpaccess]||
313
||SDR-J||"Analog" SDR & DAB||Jan van Katwijk||[http://www.sdr-j.tk]||
314 156 horiz0n
||RTLTcpSource '''(NEW)'''||source for redhawk[[br]]SDR framework||Michael Ihde||[http://redhawksdr.github.io/Documentation/ redhawk Docs page] [https://github.com/Axios-Engineering/acquisition-components RTLTcpSource]||
315 160 horiz0n
||gortlsdr '''(NEW)'''||Golang wrapper||Joseph Poirier||[https://github.com/jpoirier/gortlsdr]||
316 178 steve-m
||gr-rds (fork) '''(NEW)'''||RDS + WBFM receiver||Dimitrios Symeonidis et al||[https://github.com/bastibl/gr-rds]||
317 98 steve-m
318 91 horiz0n
[[br]]
319 176 steve-m
Also take a look at the applications which use rtl-sdr [wiki:GrOsmoSDR#KnownApps through gr-osmosdr].
320
[[br]][[br]]
321 60 horiz0n
Using our lib? Tell us! Don't? Tell us why! :)
322 91 horiz0n
[[br]][[br]][[br]]
323 6 steve-m
[[Image(rtl-sdr-gmr.png)]][[br]]
324
Multiple GMR-carriers can be seen in a spectrum view with the full 3.2 MHz bandwidth (at 3.2 MS/s).
325 132 laforge
326
== Credits ==
327
328 168 Hoernchen
rtl-sdr is developed by Steve Markgraf, Dimitri Stolnikov, and Hoernchen, with contributions by Kyle Keen, Christian Vogel and Harald Welte.
Add picture from clipboard (Maximum size: 48.8 MB)