Project

General

Profile

Rtl-sdr » History » Version 187

laforge, 04/16/2016 12:44 PM

1 185 zecke2
{{>toc}}
2 1 steve-m
3 185 zecke2
h1. rtl-sdr
4 1 steve-m
5 1 steve-m
6 185 zecke2
DVB-T dongles based on the Realtek RTL2832U can be used as a cheap SDR, since the chip allows transferring the raw I/Q samples to the host, which is officially used for DAB/DAB+/FM demodulation. The possibility of this has been discovered by Eric Fry ("History and Discovery of RTLSDR":http://rtlsdr.org/#history_and_discovery_of_rtlsdr). Antti Palosaari has not been involved in development of rtl-sdr.
7 1 steve-m
8 185 zecke2
9 185 zecke2
h2. Specifications
10 185 zecke2
11 185 zecke2
12 185 zecke2
The RTL2832U outputs 8-bit I/Q-samples, and the highest theoretically possible sample-rate is 3.2 MS/s, however, the highest sample-rate without lost samples that has been tested so far is 2.56 MS/s. The frequency range is highly dependent of the used tuner, *dongles that use the Elonics E4000 offer the widest possible range (see table below)*.
13 185 zecke2
14 186 laforge
|*Tuner*|*Frequency range*|
15 186 laforge
|Elonics E4000|52 - 2200 MHz with a gap from 1100 MHz to 1250 MHz (varies)|
16 186 laforge
|Rafael Micro R820T|24 - 1766 MHz|
17 186 laforge
|Rafael Micro R828D|24 - 1766 MHz|
18 186 laforge
|Fitipower FC0013|22 - 1100 MHz (FC0013B/C, FC0013G has a separate L-band input, which is unconnected on most sticks)|
19 186 laforge
|Fitipower FC0012|22 - 948.6 MHz|
20 186 laforge
|FCI FC2580|146 - 308 MHz and 438 - 924 MHz (gap in between)|
21 1 steve-m
22 136 steve-m
23 185 zecke2
h2. Supported Hardware
24 185 zecke2
25 185 zecke2
26 185 zecke2
*Note:* Many devices with EEPROM have 0x2838 as PID and RTL2838 as product name, but in fact all of them have an RTL2832U inside.[[br]]
27 141 steve-m
Realtek never released a chip marked as RTL2838 so far.[[br]][[br]]
28 1 steve-m
The following devices are known to work fine with RTLSDR software:
29 43 steve-m
30 186 laforge
|*VID*|*PID*|*tuner*|*device name*|
31 186 laforge
|0x0bda|0x2832|all of them|Generic RTL2832U (e.g. hama nano)|
32 186 laforge
|0x0bda|0x2838|E4000|ezcap USB 2.0 DVB-T/DAB/FM dongle|
33 186 laforge
|0x0ccd|0x00a9|FC0012|Terratec Cinergy T Stick Black (rev 1)|
34 186 laforge
|0x0ccd|0x00b3|FC0013|Terratec NOXON DAB/DAB+ USB dongle (rev 1)|
35 186 laforge
|0x0ccd|0x00d3|E4000|Terratec Cinergy T Stick RC (Rev.3)|
36 186 laforge
|0x0ccd|0x00e0|E4000|Terratec NOXON DAB/DAB+ USB dongle (rev 2)|
37 186 laforge
|0x185b|0x0620|E4000|Compro Videomate U620F|
38 186 laforge
|0x185b|0x0650|E4000|Compro Videomate U650F|
39 186 laforge
|0x1f4d|0xb803|FC0012|GTek T803|
40 186 laforge
|0x1f4d|0xc803|FC0012|Lifeview LV5TDeluxe|
41 186 laforge
|0x1b80|0xd3a4|FC0013|Twintech UT-40|
42 186 laforge
|0x1d19|0x1101|FC2580|Dexatek DK DVB-T Dongle (Logilink VG0002A)|
43 186 laforge
|0x1d19|0x1102|?|Dexatek DK DVB-T Dongle (MSI [[DigiVox]] mini II V3.0)|
44 186 laforge
|0x1d19|0x1103|FC2580|Dexatek Technology Ltd. DK 5217 DVB-T Dongle|
45 186 laforge
|0x0458|0x707f|?|Genius TVGo DVB-T03 USB dongle (Ver. B)|
46 186 laforge
|0x1b80|0xd393|FC0012|GIGABYTE GT-U7300|
47 186 laforge
|0x1b80|0xd394|?|DIKOM USB-DVBT HD|
48 186 laforge
|0x1b80|0xd395|FC0012|Peak 102569AGPK|
49 186 laforge
|0x1b80|0xd39d|FC0012|SVEON STV20 DVB-T USB & FM|
50 42 Hoernchen
51 185 zecke2
People over at reddit "are collecting a list (v2)":http://www.reddit.com/r/RTLSDR/comments/s6ddo/rtlsdr_compatibility_list_v2_work_in_progress/ of other devices that are compatible.
52 2 steve-m
53 174 steve-m
If you find a device that is not yet in the device list but should be supported, please send the VID/PID and additional info (used tuner, device name) to our mailing list.
54 5 steve-m
55 186 laforge
This is the PCB of the ezcap-stick:
56 186 laforge
!ezcap_top.jpg!
57 185 zecke2
More pictures can be found "here":http://www.steve-m.de/pictures/rtl-sdr/.
58 1 steve-m
59 2 steve-m
60 185 zecke2
h2. Software
61 185 zecke2
62 185 zecke2
63 157 sls777
Much software is available for the RTL2832. Most of the user-level packages rely on the librtlsdr library which comes as part of the rtl-sdr codebase. This codebase contains both the library itself and also a number of command line tools such as rtl_test, rtl_sdr, rtl_tcp, and rtl_fm. These command line tools use the library to test for the existence of RTL2832 devices and to perform basic data transfer functions to and from the device.
64 157 sls777
65 157 sls777
Because most of the RTL2832 devices are connected using USB, the librtlsdr library depends on the libusb library to communicate with the device.
66 158 sls777
67 181 steve-m
At the user level, there are several options for interacting with the hardware. The rtl-sdr codebase contains a basic FM receiver program that operates from the command line. The rtl_fm program is a command line tool that can initialize the RTL2832, tune to a given frequency, and output the received audio to a file or pipe the output to command line audio players such as the alsa aplay or the sox play commands. There is also the rtl_sdr program that will output the raw I-Q data to a file for more basic analysis.
68 1 steve-m
69 1 steve-m
For example, the following command will do reception of commercial wide-band FM signals:
70 1 steve-m
71 185 zecke2
<pre>
72 158 sls777
rtl_fm -f 96.3e6 -M wbfm -s 200000 -r 48000 - | aplay -r 48k -f S16_LE
73 185 zecke2
</pre>
74 1 steve-m
75 1 steve-m
On a Mac, a similar command that works is as follows. This assumes that the sox package is installed, 'port install sox':
76 1 steve-m
77 185 zecke2
<pre>
78 1 steve-m
rtl_fm -f 90100000 -M wbfm -s 200000 -r 48000 - | play -r 48000 -t s16 -L -c 1  -
79 185 zecke2
</pre>
80 1 steve-m
81 1 steve-m
If you want to do more advanced experiments, the GNU Radio collection of tools can be used to build custom radio devices. GNU Radio can be used both from a GUI perspective in which you can drag-and-drop radio components to build a radio and also programmatically where software programs written in C or Python are created that directly reference the internal GNU Radio functions.
82 1 steve-m
83 1 steve-m
The use of GNU Radio is attractive because of the large number of pre-built functions that can easily be connected together. However, be aware that this is a large body of software with dependencies on many libraries. Thankfully there is a simple script that will perform the installation but still, the time required can be on the order of hours. When starting out, it might be good to try the command line programs that come with the rtl-sdr package first and then install the GNU Radio system later.
84 158 sls777
85 157 sls777
The rtl-sdr code can be checked out with:
86 185 zecke2
<pre>
87 2 steve-m
git clone git://git.osmocom.org/rtl-sdr.git
88 185 zecke2
</pre>
89 172 steve-m
90 185 zecke2
It can also be browsed via "cgit":http://cgit.osmocom.org/cgit/rtl-sdr/, and there's an official "mirror on github":https://github.com/steve-m/librtlsdr that also provides "packaged releases":https://github.com/steve-m/librtlsdr/releases.
91 48 horiz0n
92 1 steve-m
If you are going to "fork it on github" and enhance it, please contribute back and submit your patches to: osmocom-sdr at lists.osmocom.org
93 1 steve-m
94 187 laforge
A [[GrOsmoSDR|GNU Radio source block] for [wikiWikiStart [[OsmoSDR]]]] *and rtlsdr* is available. *Please install a recent gnuradio (>= v3.6.4) in order to be able to use it.*
95 1 steve-m
96 185 zecke2
h3. Mailing List
97 1 steve-m
98 131 laforge
99 1 steve-m
We discuss both [[OsmoSDR]] as well as rtl-sdr on the following mailing list: [mailto:osmocom-sdr@lists.osmocom.org].
100 1 steve-m
101 187 laforge
You can subscribe and/or unsubscribe via the following link: https://lists.osmocom.org/mailman/listinfo/osmocom-sdr
102 1 steve-m
103 187 laforge
Please make sure to read the [[cellular-infrastructure:MailingListRules]] before posting.
104 29 horiz0n
105 187 laforge
h3. Building the software
106 185 zecke2
107 185 zecke2
h4. rtlsdr library & capture tool
108 185 zecke2
109 185 zecke2
110 185 zecke2
*You have to install development packages for libusb1.0* and can either use cmake or autotools to build the software.
111 185 zecke2
112 1 steve-m
Please note: prior pulling a new version from git and compiling it, please do a "make uninstall" first to properly remove the previous version.
113 20 horiz0n
114 1 steve-m
Building with cmake:
115 185 zecke2
<pre>
116 1 steve-m
cd rtl-sdr/
117 33 steve-m
mkdir build
118 19 steve-m
cd build
119 19 steve-m
cmake ../
120 1 steve-m
make
121 1 steve-m
sudo make install
122 1 steve-m
sudo ldconfig
123 185 zecke2
</pre>
124 1 steve-m
125 130 horiz0n
In order to be able to use the dongle as a non-root user, you may install the appropriate udev rules file by calling cmake with -DINSTALL_UDEV_RULES=ON argument in the above build steps.
126 185 zecke2
<pre>
127 1 steve-m
cmake ../ -DINSTALL_UDEV_RULES=ON
128 185 zecke2
</pre>
129 19 steve-m
130 1 steve-m
Building with autotools:
131 185 zecke2
<pre>
132 19 steve-m
cd rtl-sdr/
133 1 steve-m
autoreconf -i
134 130 horiz0n
./configure
135 1 steve-m
make
136 19 steve-m
sudo make install
137 1 steve-m
sudo ldconfig
138 185 zecke2
</pre>
139 1 steve-m
140 1 steve-m
The built executables (rtl_sdr, rtl_tcp and rtl_test) can be found in rtl-sdr/src/.
141 130 horiz0n
142 130 horiz0n
In order to be able to use the dongle as a non-root user, you may install the appropriate udev rules file by calling
143 185 zecke2
<pre>
144 1 steve-m
sudo make install-udev-rules
145 185 zecke2
</pre>
146 169 Hoernchen
147 185 zecke2
[attachment:RelWithDebInfo.zip pre-built Windows version":http://lists.osmocom.org/mailman/listinfo/osmocom-sdr]
148 1 steve-m
149 164 horiz0n
150 185 zecke2
h4. Gnuradio Source
151 1 steve-m
152 185 zecke2
153 185 zecke2
*The Gnu Radio source requires a recent gnuradio (>= v3.7 if building master branch or 3.6.5 when building gr3.6 branch) to be installed.*
154 185 zecke2
155 177 steve-m
The source supports direct device operation as well as a tcp client mode when using the rtl_tcp utility as a spectrum server.
156 1 steve-m
157 27 horiz0n
Please note: prior pulling a new version from git and compiling it, please do a "make uninstall" first to properly remove the previous version.
158 1 steve-m
159 185 zecke2
Please note: you always should build & *install the latest version of the dependencies (librtlsdr in this case)* before trying to build the gr source. The build system of gr-osmosdr will recognize them and enable specific source/sink components thereafter.
160 164 horiz0n
161 185 zecke2
Building with cmake (as described in the [[GrOsmoSDR|gr-osmosdr wiki page]]):
162 1 steve-m
163 185 zecke2
<pre>
164 164 horiz0n
git clone git://git.osmocom.org/gr-osmosdr
165 1 steve-m
cd gr-osmosdr/
166 185 zecke2
</pre>
167 1 steve-m
168 1 steve-m
If you are building for gnuradio 3.6 series, you have to switch to the gr3.6 branch as follows
169 185 zecke2
<pre>
170 1 steve-m
git checkout gr3.6
171 185 zecke2
</pre>
172 1 steve-m
173 166 horiz0n
then continue with
174 1 steve-m
175 185 zecke2
<pre>
176 1 steve-m
mkdir build
177 161 horiz0n
cd build/
178 161 horiz0n
cmake ../
179 185 zecke2
</pre>
180 161 horiz0n
181 1 steve-m
Now cmake should print out a summary of enabled/disabled components. You may disable certain components by following guidelines shown by cmake. Make sure the device of your interest is listed here. Check your dependencies and retry otherwise.
182 185 zecke2
<pre>
183 1 steve-m
-- ######################################################
184 1 steve-m
-- # gr-osmosdr enabled components                         
185 1 steve-m
-- ######################################################
186 161 horiz0n
--   * Python support
187 161 horiz0n
--   * Osmocom IQ Imbalance Correction
188 185 zecke2
--   * sysmocom [[OsmoSDR]]
189 185 zecke2
--   * [[FunCube]] Dongle
190 1 steve-m
--   * IQ File Source
191 1 steve-m
--   * Osmocom RTLSDR
192 161 horiz0n
--   * RTLSDR TCP Client
193 161 horiz0n
--   * Ettus USRP Devices
194 185 zecke2
--   * Osmocom [[MiriSDR]]
195 185 zecke2
--   * [[HackRF]] Jawbreaker
196 1 steve-m
-- 
197 1 steve-m
-- ######################################################
198 1 steve-m
-- # gr-osmosdr disabled components                        
199 1 steve-m
-- ######################################################
200 1 steve-m
-- 
201 1 steve-m
-- Building for version: 4c101ea4 / 0.0.1git
202 1 steve-m
-- Using install prefix: /usr/local
203 185 zecke2
</pre>
204 1 steve-m
205 1 steve-m
Now build & install
206 185 zecke2
<pre>
207 1 steve-m
make
208 1 steve-m
sudo make install
209 1 steve-m
sudo ldconfig
210 185 zecke2
</pre>
211 1 steve-m
212 1 steve-m
NOTE: The osmocom source block (osmocom/RTL-SDR Source) will appear under 'Sources' category in GRC menu.
213 1 steve-m
214 79 horiz0n
For initial tests we recommend the multimode receiver gnuradio companion flowgraph (see "Known Apps" table below).
215 79 horiz0n
216 185 zecke2
You may find more detailed installation instructions in this recent "tutorial":http://blog.opensecurityresearch.com/2012/06/getting-started-with-gnu-radio-and-rtl.html.
217 1 steve-m
218 79 horiz0n
219 79 horiz0n
h4. Automated installation
220 1 steve-m
221 185 zecke2
222 1 steve-m
Marcus D. Leech has kindly integrated the forementioned build steps into his gnuradio installation script at "This is the most user-friendly option so far.
223 185 zecke2
224 185 zecke2
h3. Usage
225 185 zecke2
226 185 zecke2
227 185 zecke2
228 185 zecke2
h4. rtl_sdr
229 185 zecke2
230 185 zecke2
231 76 horiz0n
Example: To tune to 392.0 MHz, and set the sample-rate to 1.8 MS/s, use:
232 110 horiz0n
233 185 zecke2
<pre>
234 1 steve-m
./rtl_sdr /tmp/capture.bin -s 1.8e6 -f 392e6
235 185 zecke2
</pre>
236 74 horiz0n
237 74 horiz0n
to record samples to a file or to forward the data to a fifo.
238 1 steve-m
239 90 horiz0n
If the device can't be opened, make sure you have the appropriate rights to access the device (install udev-rules from the repository, or run it as root).
240 90 horiz0n
241 74 horiz0n
242 185 zecke2
h4. rtl_tcp
243 185 zecke2
244 185 zecke2
245 2 steve-m
Example:
246 2 steve-m
247 185 zecke2
<pre>
248 185 zecke2
rtl_tcp -a 10.0.0.2 [-p listen port (default: 1234)":http://www.sbrac.org/files/build-gnuradio].
249 3 steve-m
Found 1 device(s).
250 2 steve-m
Found Elonics E4000 tuner
251 6 steve-m
Using Generic RTL2832U (e.g. hama nano)
252 22 horiz0n
Tuned to 100000000 Hz.
253 22 horiz0n
listening...
254 185 zecke2
Use the device argument 'rtl_tcp=10.0.0.2:1234' in [[OsmoSDR]] (gr-osmosdr) source
255 115 horiz0n
to receive samples in GRC and control rtl_tcp parameters (frequency, gain, ...).
256 185 zecke2
</pre>
257 59 horiz0n
258 32 horiz0n
use the rtl_tcp=... device argument in gr-osmosdr source to receive the samples in GRC and control the rtl settings remotely.
259 32 horiz0n
260 32 horiz0n
This application has been successfully crosscompiled for ARM and MIPS devices and is providing IQ data in a networked ADS-B setup at a rate of 2.4MSps. The gr-osmosdr source is being used together with an optimized gr-air-modes version (see Known Apps below).
261 185 zecke2
It is also available as a package in [[OpenWRT]].
262 60 horiz0n
263 185 zecke2
A use case is described "here":https://sites.google.com/site/embrtlsdr/.
264 60 horiz0n
265 185 zecke2
266 185 zecke2
h4. rtl_test
267 185 zecke2
268 89 steve-m
To check the possible tuning range (may heavily vary by some MHz depending on device and temperature), call
269 185 zecke2
<pre>
270 63 horiz0n
rtl_test -t
271 1 steve-m
</pre>
272 1 steve-m
273 1 steve-m
To check the maximum samplerate possible on your machine, type (change the rate down until no sample loss occurs):
274 1 steve-m
<pre>
275 1 steve-m
rtl_test -s 3.2e6
276 1 steve-m
</pre>
277 1 steve-m
A samplerate of 2.4e6 is known to work even over tcp connections (see rtl_tcp above). A sample rate of 2.88e6 may work without lost samples but this may depend on your PC/Laptop's host interface.
278 1 steve-m
279 1 steve-m
280 1 steve-m
h2. Using the data
281 1 steve-m
282 1 steve-m
283 1 steve-m
To convert the data to a standard cfile, following GNU Radio Block can be used:[[br]]
284 186 laforge
!rtl2832-cfile.png!
285 1 steve-m
The GNU Radio Companion flowgraph (rtl2832-cfile.grc) is attached to this page. It is based on the FM demodulation flowgraph posted by Alistair Buxton "on this thread":http://thread.gmane.org/gmane.linux.drivers.video-input-infrastructure/44461/focus=44525.
286 1 steve-m
287 1 steve-m
Please note: for realtime operation you may use fifos (mkfifo) to forward the iq data from the capture utility to the GRC flowgraph.
288 1 steve-m
289 1 steve-m
You may use any of the the following gnuradio sources (they are equivalent):
290 186 laforge
[[br]][[br]]!osmosource.png![[br]]
291 1 steve-m
292 1 steve-m
What has been successfully tested so far is the reception of "Broadcast FM and air traffic AM":https://www.cgran.org/browser/projects/multimode/trunk radio, "TETRA":http://tetra.osmocom.org/, "GMR":http://gmr.osmocom.org/, "GSM":http://svn.berlin.ccc.de/projects/airprobe/, "ADS-B":https://www.cgran.org/wiki/gr-air-modes and "POCSAG":https://github.com/smunaut/osmo-pocsag.
293 1 steve-m
294 1 steve-m
Tell us your success story with other wireless protocols in ##rtlsdr channel on freenode IRC network.
295 116 horiz0n
296 185 zecke2
297 128 horiz0n
h2. Known Apps
298 128 horiz0n
299 128 horiz0n
300 185 zecke2
The following 3rd party applications and libraries are successfully using either librtlsdr directly or the corresponding gnuradio source (gr-osmosdr):
301 185 zecke2
302 186 laforge
|*Name*|*Type*|*Author*|*URL*|
303 186 laforge
|gr-pocsag|GRC Flowgraph|Marcus Leech|https://www.cgran.org/browser/projects/gr-pocsag/trunk|
304 186 laforge
|multimode RX (try first!)|GRC Flowgraph|Marcus Leech|https://www.cgran.org/browser/projects/multimode/trunk|
305 186 laforge
|simple_fm_rvc|GRC Flowgraph|Marcus Leech|https://www.cgran.org/browser/projects/simple_fm_rcv/trunk|
306 186 laforge
|python-librtlsdr|Python Wrapper|David Basden|https://github.com/dbasden/python-librtlsdr|
307 186 laforge
|pyrtlsdr|Python Wrapper|Roger|https://github.com/roger-/pyrtlsdr|
308 186 laforge
|rtlsdr-waterfall|Python FFT GUI|Kyle Keen|https://github.com/keenerd/rtlsdr-waterfall|
309 186 laforge
|Wireless Temp. Sensor RX|Gnuradio App|Kevin Mehall|https://github.com/kevinmehall/rtlsdr-433m-sensor|
310 186 laforge
|QtRadio|SDR GUI|Andrea Montefusco et al.|http://napan.ca/ghpsdr3/index.php/RTL-SDR|
311 186 laforge
|gqrx|SDR GUI|Alexandru Csete|https://github.com/csete/gqrx|
312 186 laforge
|rtl_fm|SDR CLI|Kyle Keen|merged in librtlsdr master|
313 186 laforge
|SDR#|SDR GUI|Youssef Touil|http://sdrsharp.com/ and "Windows Guide":http://rtlsdr.org/softwarewindows or "Linux Guide":http://rtlsdr.org/softwarelinux|
314 186 laforge
|tetra_demod_fft|Trunking RX|osmocom team|"osmosdr-tetra_demod_fft.py":http://cgit.osmocom.org/cgit/osmo-tetra/tree/src/demod/python/osmosdr-tetra_demod_fft.py and the "HOWTO":http://tetra.osmocom.org/trac/wiki/osmo-tetra#Quickexample|
315 186 laforge
|airprobe|GSM sniffer|osmocom team et al|http://git.gnumonks.org/cgi-bin/gitweb.cgi?p=airprobe.git|
316 186 laforge
|gr-smartnet (WIP)|Trunking RX|Nick Foster|http://www.reddit.com/r/RTLSDR/comments/us3yo/rtlsdr_smartnet/ "Notes from the author":http://www.reddit.com/r/RTLSDR/comments/vbxl0/attention_grsmartnet_users_or_attempted_users/|
317 186 laforge
|gr-air-modes|ADS-B RX|Nick Foster|https://www.cgran.org/wiki/gr-air-modes call with --rtlsdr option|
318 186 laforge
|Linrad|SDR GUI|Leif Asbrink (SM5BSZ)|http://www.nitehawk.com/sm5bsz/linuxdsp/hware/rtlsdr/rtlsdr.htm" DAGC changes were applied to librtlsdr master|
319 186 laforge
|gr-ais (fork)|AIS RX|Nick Foster, Antoine Sirinelli, Christian Gagneraud|https://github.com/chgans/gr-ais|
320 186 laforge
|GNSS-SDR|GPS RX (Realtime!)|Centre Tecnològic de elecomunicacions de Catalunya|"Documentation":http://www.gnss-sdr.org/documentation/gnss-sdr-operation-realtek-rtl2832u-usb-dongle-dvb-t-receiver and http://www.gnss-sdr.org/|
321 186 laforge
|LTE-Cell-Scanner|LTE Scanner / Tracker|James Peroulas, Evrytania LLC|http://www.evrytania.com/lte-tools https://github.com/Evrytania/LTE-Cell-Scanner]|
322 186 laforge
|LTE-Cell-Scanner OpenCL accelerated *(new)*|LTE Scanner / Tracker|Jiao Xianjun|https://github.com/JiaoXianjun/LTE-Cell-Scanner|
323 186 laforge
|Simulink-RTL-SDR|MATLAB/Simulink wrapper|Michael Schwall, Sebastian Koslowski, Communication Engineering Lab (CEL), Karlsruhe Institute of Technology (KIT)|http://www.cel.kit.edu/simulink_rtl_sdr.php|
324 186 laforge
|gr-scan|Scanner|techmeology|http://www.techmeology.co.uk/gr-scan/|
325 186 laforge
|kalibrate-rtl|calibration tool|Joshua Lackey, Alexander Chemeris, Steve Markgraf|https://github.com/steve-m/kalibrate-rtl "Windows build":http://rtlsdr.org/files/kalibrate-win-release.zip|
326 186 laforge
|pocsag-mrt|Multichannel Realtime ]Decoder|iZsh|https://github.com/iZsh/pocsag-mrt|
327 186 laforge
|adsb#|ADS-B RX|Youssef Touil, Ian Gilmour|http://sdrsharp.com/index.php/a-simple-and-cheap-ads-b-receiver-using-rtl-sdr|
328 186 laforge
|osmo-gmr-rtl|GMR1 RX|Dimitri Stolnikov|http://gmr.osmocom.org/trac/wiki/GettingStarted#RTLSDRdongles|
329 186 laforge
|rtl_adsb|ADS-B RX|Kyle Keen|comes with the library|
330 186 laforge
|dump1090|ADS-B RX|Salvatore Sanfilippo|https://github.com/antirez/dump1090|
331 186 laforge
|rtl_433|Temperature Sensor Receiver|Benjamin Larsson|https://github.com/merbanan/rtl_433|
332 186 laforge
|randio|Random number generator|Michel Pelletier|https://github.com/michelp/randio|
333 186 laforge
|gr-wmbus|m-bus (EN 13757-4) RX|oWCTejLVlFyNztcBnOoh|https://github.com/oWCTejLVlFyNztcBnOoh/gr-wmbus|
334 186 laforge
|ec3k|EnergyCount 3000 RX|Tomaž Šolc|https://github.com/avian2/ec3k|
335 186 laforge
|RTLSDR-Scanner|Radio Scanner|EarToEarOak|https://github.com/EarToEarOak/RTLSDR-Scanner|
336 186 laforge
|simple_ra|Radio Astronomy App|Marcus Leech|https://cgran.org/wiki/simple_ra|
337 186 laforge
|rtlizer|Spectrum analyzer|Alexandru Csete|https://github.com/csete/rtlizer|
338 186 laforge
|FS20_decode|FS20 Decoder|Thomas Frisch|https://github.com/eT0M/rtl_sdr_FS20_decoder|
339 186 laforge
|OpenLTE|LTE Toolkit|Ben Wojtowicz|http://sourceforge.net/p/openlte/home/Home/|
340 186 laforge
|rtltcpaccess|DAB compatibility layer|Steve Markgraf|https://github.com/steve-m/rtltcpaccess|
341 186 laforge
|SDR-J|"Analog" SDR & DAB|Jan van Katwijk|http://www.sdr-j.tk|
342 186 laforge
|RTLTcpSource|source for redhawk SDR framework|Michael Ihde|"redhawk Docs page":http://redhawksdr.github.io/Documentation/ "RTLTcpSource":https://github.com/Axios-Engineering/acquisition-components|
343 186 laforge
|gortlsdr|Golang wrapper|Joseph Poirier|https://github.com/jpoirier/gortlsdr|
344 186 laforge
|gr-rds (fork)|RDS + WBFM receiver|Dimitrios Symeonidis et al|https://github.com/bastibl/gr-rds|
345 186 laforge
|NRF24-BTLE-Decoder|Decoder for 2.4 GHz NRF24 & Bluetooh LE|Omri Iluz|"Code":https://github.com/omriiluz/NRF24-BTLE-Decoder "Blog post":http://blog.cyberexplorer.me/2014/01/sniffing-and-decoding-nrf24l01-and.html|
346 186 laforge
|acarsdec|ACARS decoder|Thierry Leconte|http://sourceforge.net/projects/acarsdec/|
347 186 laforge
348 186 laforge
349 1 steve-m
Also take a look at the applications which use rtl-sdr [[GrOsmoSDR#KnownApps|through gr-osmosdr]].
350 186 laforge
351 1 steve-m
Using our lib? Tell us! Don't? Tell us why! :)
352 1 steve-m
353 186 laforge
!rtl-sdr-gmr.png!
354 186 laforge
Multiple GMR-carriers can be seen in a spectrum view with the full 3.2 MHz bandwidth (at 3.2 MS/s).
355 185 zecke2
356 185 zecke2
h2. Credits
357 1 steve-m
358 1 steve-m
359 1 steve-m
rtl-sdr is developed by Steve Markgraf, Dimitri Stolnikov, and Hoernchen, with contributions by Kyle Keen, Christian Vogel and Harald Welte.
Add picture from clipboard (Maximum size: 48.8 MB)