Project

General

Profile

Rtl-sdr » History » Version 198

steve-m, 05/28/2021 10:59 AM

1 185 zecke2
{{>toc}}
2 1 steve-m
3 185 zecke2
h1. rtl-sdr
4 1 steve-m
5 1 steve-m
6 185 zecke2
DVB-T dongles based on the Realtek RTL2832U can be used as a cheap SDR, since the chip allows transferring the raw I/Q samples to the host, which is officially used for DAB/DAB+/FM demodulation. The possibility of this has been discovered by Eric Fry ("History and Discovery of RTLSDR":http://rtlsdr.org/#history_and_discovery_of_rtlsdr). Antti Palosaari has not been involved in development of rtl-sdr.
7 1 steve-m
8 185 zecke2
h2. Specifications
9 185 zecke2
10 1 steve-m
11 196 steve-m
The RTL2832U outputs 8-bit I/Q-samples, and the highest theoretically possible sample-rate is 3.2 MS/s, however, the highest sample-rate without lost samples that has been tested wit regular USB controllers so far is 2.4 MS/s. A stable sample-rate of 3.2 MS/s without lost samples is only possible with the Etron EJ168/EJ188/EJ198 series of host controllers due to their "specific maximum latency":https://osmocom.org/attachments/3979/Histo_DATA_Packets.png.  The frequency range is highly dependent of the used tuner, *dongles that use the Elonics E4000 offer the widest possible range (see table below)*.
12 185 zecke2
13 186 laforge
|*Tuner*|*Frequency range*|
14 186 laforge
|Elonics E4000|52 - 2200 MHz with a gap from 1100 MHz to 1250 MHz (varies)|
15 186 laforge
|Rafael Micro R820T|24 - 1766 MHz|
16 186 laforge
|Rafael Micro R828D|24 - 1766 MHz|
17 186 laforge
|Fitipower FC0013|22 - 1100 MHz (FC0013B/C, FC0013G has a separate L-band input, which is unconnected on most sticks)|
18 186 laforge
|Fitipower FC0012|22 - 948.6 MHz|
19 186 laforge
|FCI FC2580|146 - 308 MHz and 438 - 924 MHz (gap in between)|
20 1 steve-m
21 185 zecke2
h2. Supported Hardware
22 185 zecke2
23 185 zecke2
24 1 steve-m
*Note:* Many devices with EEPROM have 0x2838 as PID and RTL2838 as product name, but in fact all of them have an RTL2832U inside.[[br]]
25 188 steve-m
Realtek never released a chip marked as RTL2838 so far.
26 1 steve-m
The following devices are known to work fine with RTLSDR software:
27 43 steve-m
28 186 laforge
|*VID*|*PID*|*tuner*|*device name*|
29 186 laforge
|0x0bda|0x2832|all of them|Generic RTL2832U (e.g. hama nano)|
30 186 laforge
|0x0bda|0x2838|E4000|ezcap USB 2.0 DVB-T/DAB/FM dongle|
31 186 laforge
|0x0ccd|0x00a9|FC0012|Terratec Cinergy T Stick Black (rev 1)|
32 186 laforge
|0x0ccd|0x00b3|FC0013|Terratec NOXON DAB/DAB+ USB dongle (rev 1)|
33 186 laforge
|0x0ccd|0x00d3|E4000|Terratec Cinergy T Stick RC (Rev.3)|
34 186 laforge
|0x0ccd|0x00e0|E4000|Terratec NOXON DAB/DAB+ USB dongle (rev 2)|
35 186 laforge
|0x185b|0x0620|E4000|Compro Videomate U620F|
36 186 laforge
|0x185b|0x0650|E4000|Compro Videomate U650F|
37 186 laforge
|0x1f4d|0xb803|FC0012|GTek T803|
38 186 laforge
|0x1f4d|0xc803|FC0012|Lifeview LV5TDeluxe|
39 186 laforge
|0x1b80|0xd3a4|FC0013|Twintech UT-40|
40 186 laforge
|0x1d19|0x1101|FC2580|Dexatek DK DVB-T Dongle (Logilink VG0002A)|
41 186 laforge
|0x1d19|0x1102|?|Dexatek DK DVB-T Dongle (MSI [[DigiVox]] mini II V3.0)|
42 186 laforge
|0x1d19|0x1103|FC2580|Dexatek Technology Ltd. DK 5217 DVB-T Dongle|
43 186 laforge
|0x0458|0x707f|?|Genius TVGo DVB-T03 USB dongle (Ver. B)|
44 186 laforge
|0x1b80|0xd393|FC0012|GIGABYTE GT-U7300|
45 186 laforge
|0x1b80|0xd394|?|DIKOM USB-DVBT HD|
46 186 laforge
|0x1b80|0xd395|FC0012|Peak 102569AGPK|
47 186 laforge
|0x1b80|0xd39d|FC0012|SVEON STV20 DVB-T USB & FM|
48 42 Hoernchen
49 185 zecke2
People over at reddit "are collecting a list (v2)":http://www.reddit.com/r/RTLSDR/comments/s6ddo/rtlsdr_compatibility_list_v2_work_in_progress/ of other devices that are compatible.
50 2 steve-m
51 174 steve-m
If you find a device that is not yet in the device list but should be supported, please send the VID/PID and additional info (used tuner, device name) to our mailing list.
52 5 steve-m
53 186 laforge
This is the PCB of the ezcap-stick:
54 186 laforge
!ezcap_top.jpg!
55 1 steve-m
More pictures can be found "here":http://www.steve-m.de/pictures/rtl-sdr/.
56 2 steve-m
57 185 zecke2
h2. Software
58 185 zecke2
59 185 zecke2
60 157 sls777
Much software is available for the RTL2832. Most of the user-level packages rely on the librtlsdr library which comes as part of the rtl-sdr codebase. This codebase contains both the library itself and also a number of command line tools such as rtl_test, rtl_sdr, rtl_tcp, and rtl_fm. These command line tools use the library to test for the existence of RTL2832 devices and to perform basic data transfer functions to and from the device.
61 157 sls777
62 157 sls777
Because most of the RTL2832 devices are connected using USB, the librtlsdr library depends on the libusb library to communicate with the device.
63 158 sls777
64 181 steve-m
At the user level, there are several options for interacting with the hardware. The rtl-sdr codebase contains a basic FM receiver program that operates from the command line. The rtl_fm program is a command line tool that can initialize the RTL2832, tune to a given frequency, and output the received audio to a file or pipe the output to command line audio players such as the alsa aplay or the sox play commands. There is also the rtl_sdr program that will output the raw I-Q data to a file for more basic analysis.
65 1 steve-m
66 1 steve-m
For example, the following command will do reception of commercial wide-band FM signals:
67 1 steve-m
68 185 zecke2
<pre>
69 158 sls777
rtl_fm -f 96.3e6 -M wbfm -s 200000 -r 48000 - | aplay -r 48k -f S16_LE
70 185 zecke2
</pre>
71 1 steve-m
72 1 steve-m
On a Mac, a similar command that works is as follows. This assumes that the sox package is installed, 'port install sox':
73 1 steve-m
74 185 zecke2
<pre>
75 1 steve-m
rtl_fm -f 90100000 -M wbfm -s 200000 -r 48000 - | play -r 48000 -t s16 -L -c 1  -
76 185 zecke2
</pre>
77 1 steve-m
78 1 steve-m
If you want to do more advanced experiments, the GNU Radio collection of tools can be used to build custom radio devices. GNU Radio can be used both from a GUI perspective in which you can drag-and-drop radio components to build a radio and also programmatically where software programs written in C or Python are created that directly reference the internal GNU Radio functions.
79 1 steve-m
80 1 steve-m
The use of GNU Radio is attractive because of the large number of pre-built functions that can easily be connected together. However, be aware that this is a large body of software with dependencies on many libraries. Thankfully there is a simple script that will perform the installation but still, the time required can be on the order of hours. When starting out, it might be good to try the command line programs that come with the rtl-sdr package first and then install the GNU Radio system later.
81 158 sls777
82 190 laforge
h3. Binary Builds
83 190 laforge
84 190 laforge
h4. Windows
85 190 laforge
86 190 laforge
While Osmocom in general is a very much Linux-centric development community, we are now finally publishing automatic weekly Windows binary builds for the most widely used Osmocom SDR related projects:  [[rtl-sdr:]] and [[osmo-fl2k:]].
87 190 laforge
88 190 laforge
You can find the binaries at
89 190 laforge
* https://ftp.osmocom.org/binaries/windows/osmo-fl2k/
90 190 laforge
* https://ftp.osmocom.org/binaries/windows/rtl-sdr/
91 190 laforge
92 190 laforge
The actual builds are done by @roox who is building them using MinGW on OBS, see
93 190 laforge
* https://build.opensuse.org/project/show/network:osmocom:mingw:mingw32 and
94 190 laforge
* https://build.opensuse.org/project/show/network:osmocom:mingw:mingw64
95 190 laforge
96 190 laforge
The status of the osmocom binary publish job, executed once per week from now on, can be found at https://jenkins.osmocom.org/jenkins/view/All%20no%20Gerrit/job/Osmocom-OBS_MinGW_weekly_publish/
97 190 laforge
98 189 laforge
h3. Source Code
99 189 laforge
100 157 sls777
The rtl-sdr code can be checked out with:
101 185 zecke2
<pre>
102 2 steve-m
git clone git://git.osmocom.org/rtl-sdr.git
103 185 zecke2
</pre>
104 172 steve-m
105 185 zecke2
It can also be browsed via "cgit":http://cgit.osmocom.org/cgit/rtl-sdr/, and there's an official "mirror on github":https://github.com/steve-m/librtlsdr that also provides "packaged releases":https://github.com/steve-m/librtlsdr/releases.
106 48 horiz0n
107 1 steve-m
If you are going to "fork it on github" and enhance it, please contribute back and submit your patches to: osmocom-sdr at lists.osmocom.org
108 1 steve-m
109 191 laforge
A [[gr-osmosdr:]] GNU Radio source block for [[OsmoSDR:]] *and rtl-sdr* is available. *Please install a recent gnuradio (>= v3.6.4) in order to be able to use it.*
110 29 horiz0n
111 187 laforge
h3. Building the software
112 185 zecke2
113 185 zecke2
h4. rtlsdr library & capture tool
114 185 zecke2
115 185 zecke2
116 185 zecke2
*You have to install development packages for libusb1.0* and can either use cmake or autotools to build the software.
117 185 zecke2
118 1 steve-m
Please note: prior pulling a new version from git and compiling it, please do a "make uninstall" first to properly remove the previous version.
119 20 horiz0n
120 1 steve-m
Building with cmake:
121 185 zecke2
<pre>
122 1 steve-m
cd rtl-sdr/
123 33 steve-m
mkdir build
124 19 steve-m
cd build
125 19 steve-m
cmake ../
126 1 steve-m
make
127 1 steve-m
sudo make install
128 1 steve-m
sudo ldconfig
129 185 zecke2
</pre>
130 1 steve-m
131 130 horiz0n
In order to be able to use the dongle as a non-root user, you may install the appropriate udev rules file by calling cmake with -DINSTALL_UDEV_RULES=ON argument in the above build steps.
132 185 zecke2
<pre>
133 1 steve-m
cmake ../ -DINSTALL_UDEV_RULES=ON
134 185 zecke2
</pre>
135 19 steve-m
136 1 steve-m
Building with autotools:
137 185 zecke2
<pre>
138 19 steve-m
cd rtl-sdr/
139 1 steve-m
autoreconf -i
140 130 horiz0n
./configure
141 1 steve-m
make
142 19 steve-m
sudo make install
143 1 steve-m
sudo ldconfig
144 185 zecke2
</pre>
145 1 steve-m
146 1 steve-m
The built executables (rtl_sdr, rtl_tcp and rtl_test) can be found in rtl-sdr/src/.
147 130 horiz0n
148 130 horiz0n
In order to be able to use the dongle as a non-root user, you may install the appropriate udev rules file by calling
149 185 zecke2
<pre>
150 1 steve-m
sudo make install-udev-rules
151 185 zecke2
</pre>
152 169 Hoernchen
153 185 zecke2
[attachment:RelWithDebInfo.zip pre-built Windows version":http://lists.osmocom.org/mailman/listinfo/osmocom-sdr]
154 1 steve-m
155 164 horiz0n
156 185 zecke2
h4. Gnuradio Source
157 1 steve-m
158 185 zecke2
159 185 zecke2
*The Gnu Radio source requires a recent gnuradio (>= v3.7 if building master branch or 3.6.5 when building gr3.6 branch) to be installed.*
160 185 zecke2
161 177 steve-m
The source supports direct device operation as well as a tcp client mode when using the rtl_tcp utility as a spectrum server.
162 1 steve-m
163 27 horiz0n
Please note: prior pulling a new version from git and compiling it, please do a "make uninstall" first to properly remove the previous version.
164 1 steve-m
165 185 zecke2
Please note: you always should build & *install the latest version of the dependencies (librtlsdr in this case)* before trying to build the gr source. The build system of gr-osmosdr will recognize them and enable specific source/sink components thereafter.
166 164 horiz0n
167 185 zecke2
Building with cmake (as described in the [[GrOsmoSDR|gr-osmosdr wiki page]]):
168 1 steve-m
169 185 zecke2
<pre>
170 164 horiz0n
git clone git://git.osmocom.org/gr-osmosdr
171 1 steve-m
cd gr-osmosdr/
172 185 zecke2
</pre>
173 1 steve-m
174 1 steve-m
If you are building for gnuradio 3.6 series, you have to switch to the gr3.6 branch as follows
175 185 zecke2
<pre>
176 1 steve-m
git checkout gr3.6
177 185 zecke2
</pre>
178 1 steve-m
179 166 horiz0n
then continue with
180 1 steve-m
181 185 zecke2
<pre>
182 1 steve-m
mkdir build
183 161 horiz0n
cd build/
184 161 horiz0n
cmake ../
185 185 zecke2
</pre>
186 161 horiz0n
187 1 steve-m
Now cmake should print out a summary of enabled/disabled components. You may disable certain components by following guidelines shown by cmake. Make sure the device of your interest is listed here. Check your dependencies and retry otherwise.
188 185 zecke2
<pre>
189 1 steve-m
-- ######################################################
190 1 steve-m
-- # gr-osmosdr enabled components                         
191 1 steve-m
-- ######################################################
192 161 horiz0n
--   * Python support
193 161 horiz0n
--   * Osmocom IQ Imbalance Correction
194 185 zecke2
--   * sysmocom [[OsmoSDR]]
195 185 zecke2
--   * [[FunCube]] Dongle
196 1 steve-m
--   * IQ File Source
197 1 steve-m
--   * Osmocom RTLSDR
198 161 horiz0n
--   * RTLSDR TCP Client
199 161 horiz0n
--   * Ettus USRP Devices
200 185 zecke2
--   * Osmocom [[MiriSDR]]
201 185 zecke2
--   * [[HackRF]] Jawbreaker
202 1 steve-m
-- 
203 1 steve-m
-- ######################################################
204 1 steve-m
-- # gr-osmosdr disabled components                        
205 1 steve-m
-- ######################################################
206 1 steve-m
-- 
207 1 steve-m
-- Building for version: 4c101ea4 / 0.0.1git
208 1 steve-m
-- Using install prefix: /usr/local
209 185 zecke2
</pre>
210 1 steve-m
211 1 steve-m
Now build & install
212 185 zecke2
<pre>
213 1 steve-m
make
214 1 steve-m
sudo make install
215 1 steve-m
sudo ldconfig
216 185 zecke2
</pre>
217 1 steve-m
218 1 steve-m
NOTE: The osmocom source block (osmocom/RTL-SDR Source) will appear under 'Sources' category in GRC menu.
219 1 steve-m
220 1 steve-m
For initial tests we recommend the multimode receiver gnuradio companion flowgraph (see "Known Apps" table below).
221 79 horiz0n
222 79 horiz0n
You may find more detailed installation instructions in this recent "tutorial":http://blog.opensecurityresearch.com/2012/06/getting-started-with-gnu-radio-and-rtl.html.
223 1 steve-m
224 185 zecke2
225 1 steve-m
h4. Automated installation
226 1 steve-m
227 1 steve-m
228 79 horiz0n
Marcus D. Leech has kindly integrated the forementioned build steps into his gnuradio installation script at "This is the most user-friendly option so far.
229 189 laforge
h2. Mailing List
230 1 steve-m
231 1 steve-m
232 189 laforge
We discuss both [[OsmoSDR]] as well as rtl-sdr on the following mailing list: [mailto:osmocom-sdr@lists.osmocom.org].
233 1 steve-m
234 189 laforge
You can subscribe and/or unsubscribe via the following link: https://lists.osmocom.org/mailman/listinfo/osmocom-sdr
235 1 steve-m
236 189 laforge
Please make sure to read the [[cellular-infrastructure:MailingListRules]] before posting.
237 185 zecke2
238 185 zecke2
239 189 laforge
h3. Usage
240 189 laforge
241 189 laforge
h4. rtl-sdr
242 189 laforge
243 189 laforge
244 76 horiz0n
Example: To tune to 392.0 MHz, and set the sample-rate to 1.8 MS/s, use:
245 110 horiz0n
246 185 zecke2
<pre>
247 1 steve-m
./rtl_sdr /tmp/capture.bin -s 1.8e6 -f 392e6
248 185 zecke2
</pre>
249 74 horiz0n
250 74 horiz0n
to record samples to a file or to forward the data to a fifo.
251 1 steve-m
252 90 horiz0n
If the device can't be opened, make sure you have the appropriate rights to access the device (install udev-rules from the repository, or run it as root).
253 90 horiz0n
254 74 horiz0n
255 185 zecke2
h4. rtl_tcp
256 185 zecke2
257 185 zecke2
258 2 steve-m
Example:
259 2 steve-m
260 185 zecke2
<pre>
261 185 zecke2
rtl_tcp -a 10.0.0.2 [-p listen port (default: 1234)":http://www.sbrac.org/files/build-gnuradio].
262 3 steve-m
Found 1 device(s).
263 2 steve-m
Found Elonics E4000 tuner
264 6 steve-m
Using Generic RTL2832U (e.g. hama nano)
265 22 horiz0n
Tuned to 100000000 Hz.
266 22 horiz0n
listening...
267 185 zecke2
Use the device argument 'rtl_tcp=10.0.0.2:1234' in [[OsmoSDR]] (gr-osmosdr) source
268 115 horiz0n
to receive samples in GRC and control rtl_tcp parameters (frequency, gain, ...).
269 185 zecke2
</pre>
270 59 horiz0n
271 32 horiz0n
use the rtl_tcp=... device argument in gr-osmosdr source to receive the samples in GRC and control the rtl settings remotely.
272 32 horiz0n
273 32 horiz0n
This application has been successfully crosscompiled for ARM and MIPS devices and is providing IQ data in a networked ADS-B setup at a rate of 2.4MSps. The gr-osmosdr source is being used together with an optimized gr-air-modes version (see Known Apps below).
274 185 zecke2
It is also available as a package in [[OpenWRT]].
275 60 horiz0n
276 185 zecke2
A use case is described "here":https://sites.google.com/site/embrtlsdr/.
277 60 horiz0n
278 185 zecke2
279 185 zecke2
h4. rtl_test
280 89 steve-m
281 185 zecke2
To check the possible tuning range (may heavily vary by some MHz depending on device and temperature), call
282 63 horiz0n
<pre>
283 1 steve-m
rtl_test -t
284 1 steve-m
</pre>
285 1 steve-m
286 1 steve-m
To check the maximum samplerate possible on your machine, type (change the rate down until no sample loss occurs):
287 1 steve-m
<pre>
288 1 steve-m
rtl_test -s 3.2e6
289 1 steve-m
</pre>
290 1 steve-m
A samplerate of 2.4e6 is known to work even over tcp connections (see rtl_tcp above). A sample rate of 2.88e6 may work without lost samples but this may depend on your PC/Laptop's host interface.
291 1 steve-m
292 1 steve-m
h2. Using the data
293 1 steve-m
294 1 steve-m
295 1 steve-m
To convert the data to a standard cfile, following GNU Radio Block can be used:[[br]]
296 186 laforge
!rtl2832-cfile.png!
297 194 laforge
The GNU Radio Companion flowgraph is available as attachment:rtl2832-cfile.grc. It is based on the FM demodulation flowgraph posted by Alistair Buxton "on this thread":http://thread.gmane.org/gmane.linux.drivers.video-input-infrastructure/44461/focus=44525.
298 1 steve-m
299 1 steve-m
Please note: for realtime operation you may use fifos (mkfifo) to forward the iq data from the capture utility to the GRC flowgraph.
300 1 steve-m
301 1 steve-m
You may use any of the the following gnuradio sources (they are equivalent):
302 1 steve-m
303 192 laforge
!osmosource.png!
304 192 laforge
305 1 steve-m
What has been successfully tested so far is the reception of "Broadcast FM and air traffic AM":https://www.cgran.org/browser/projects/multimode/trunk radio, "TETRA":http://tetra.osmocom.org/, "GMR":http://gmr.osmocom.org/, "GSM":http://svn.berlin.ccc.de/projects/airprobe/, "ADS-B":https://www.cgran.org/wiki/gr-air-modes and "POCSAG":https://github.com/smunaut/osmo-pocsag.
306 1 steve-m
307 198 steve-m
Tell us your success story with other wireless protocols in ##rtlsdr channel on the "libera":https://libera.chat/ IRC network.
308 185 zecke2
309 128 horiz0n
h2. Known Apps
310 128 horiz0n
311 128 horiz0n
312 185 zecke2
The following 3rd party applications and libraries are successfully using either librtlsdr directly or the corresponding gnuradio source (gr-osmosdr):
313 185 zecke2
314 186 laforge
|*Name*|*Type*|*Author*|*URL*|
315 186 laforge
|gr-pocsag|GRC Flowgraph|Marcus Leech|https://www.cgran.org/browser/projects/gr-pocsag/trunk|
316 186 laforge
|multimode RX (try first!)|GRC Flowgraph|Marcus Leech|https://www.cgran.org/browser/projects/multimode/trunk|
317 186 laforge
|simple_fm_rvc|GRC Flowgraph|Marcus Leech|https://www.cgran.org/browser/projects/simple_fm_rcv/trunk|
318 186 laforge
|python-librtlsdr|Python Wrapper|David Basden|https://github.com/dbasden/python-librtlsdr|
319 186 laforge
|pyrtlsdr|Python Wrapper|Roger|https://github.com/roger-/pyrtlsdr|
320 186 laforge
|rtlsdr-waterfall|Python FFT GUI|Kyle Keen|https://github.com/keenerd/rtlsdr-waterfall|
321 186 laforge
|Wireless Temp. Sensor RX|Gnuradio App|Kevin Mehall|https://github.com/kevinmehall/rtlsdr-433m-sensor|
322 186 laforge
|QtRadio|SDR GUI|Andrea Montefusco et al.|http://napan.ca/ghpsdr3/index.php/RTL-SDR|
323 186 laforge
|gqrx|SDR GUI|Alexandru Csete|https://github.com/csete/gqrx|
324 186 laforge
|rtl_fm|SDR CLI|Kyle Keen|merged in librtlsdr master|
325 186 laforge
|SDR#|SDR GUI|Youssef Touil|http://sdrsharp.com/ and "Windows Guide":http://rtlsdr.org/softwarewindows or "Linux Guide":http://rtlsdr.org/softwarelinux|
326 186 laforge
|tetra_demod_fft|Trunking RX|osmocom team|"osmosdr-tetra_demod_fft.py":http://cgit.osmocom.org/cgit/osmo-tetra/tree/src/demod/python/osmosdr-tetra_demod_fft.py and the "HOWTO":http://tetra.osmocom.org/trac/wiki/osmo-tetra#Quickexample|
327 186 laforge
|airprobe|GSM sniffer|osmocom team et al|http://git.gnumonks.org/cgi-bin/gitweb.cgi?p=airprobe.git|
328 186 laforge
|gr-smartnet (WIP)|Trunking RX|Nick Foster|http://www.reddit.com/r/RTLSDR/comments/us3yo/rtlsdr_smartnet/ "Notes from the author":http://www.reddit.com/r/RTLSDR/comments/vbxl0/attention_grsmartnet_users_or_attempted_users/|
329 186 laforge
|gr-air-modes|ADS-B RX|Nick Foster|https://www.cgran.org/wiki/gr-air-modes call with --rtlsdr option|
330 186 laforge
|Linrad|SDR GUI|Leif Asbrink (SM5BSZ)|http://www.nitehawk.com/sm5bsz/linuxdsp/hware/rtlsdr/rtlsdr.htm" DAGC changes were applied to librtlsdr master|
331 186 laforge
|gr-ais (fork)|AIS RX|Nick Foster, Antoine Sirinelli, Christian Gagneraud|https://github.com/chgans/gr-ais|
332 186 laforge
|GNSS-SDR|GPS RX (Realtime!)|Centre Tecnològic de elecomunicacions de Catalunya|"Documentation":http://www.gnss-sdr.org/documentation/gnss-sdr-operation-realtek-rtl2832u-usb-dongle-dvb-t-receiver and http://www.gnss-sdr.org/|
333 186 laforge
|LTE-Cell-Scanner|LTE Scanner / Tracker|James Peroulas, Evrytania LLC|http://www.evrytania.com/lte-tools https://github.com/Evrytania/LTE-Cell-Scanner]|
334 186 laforge
|LTE-Cell-Scanner OpenCL accelerated *(new)*|LTE Scanner / Tracker|Jiao Xianjun|https://github.com/JiaoXianjun/LTE-Cell-Scanner|
335 186 laforge
|Simulink-RTL-SDR|MATLAB/Simulink wrapper|Michael Schwall, Sebastian Koslowski, Communication Engineering Lab (CEL), Karlsruhe Institute of Technology (KIT)|http://www.cel.kit.edu/simulink_rtl_sdr.php|
336 186 laforge
|gr-scan|Scanner|techmeology|http://www.techmeology.co.uk/gr-scan/|
337 186 laforge
|kalibrate-rtl|calibration tool|Joshua Lackey, Alexander Chemeris, Steve Markgraf|https://github.com/steve-m/kalibrate-rtl "Windows build":http://rtlsdr.org/files/kalibrate-win-release.zip|
338 186 laforge
|pocsag-mrt|Multichannel Realtime ]Decoder|iZsh|https://github.com/iZsh/pocsag-mrt|
339 186 laforge
|adsb#|ADS-B RX|Youssef Touil, Ian Gilmour|http://sdrsharp.com/index.php/a-simple-and-cheap-ads-b-receiver-using-rtl-sdr|
340 186 laforge
|osmo-gmr-rtl|GMR1 RX|Dimitri Stolnikov|http://gmr.osmocom.org/trac/wiki/GettingStarted#RTLSDRdongles|
341 186 laforge
|rtl_adsb|ADS-B RX|Kyle Keen|comes with the library|
342 186 laforge
|dump1090|ADS-B RX|Salvatore Sanfilippo|https://github.com/antirez/dump1090|
343 186 laforge
|rtl_433|Temperature Sensor Receiver|Benjamin Larsson|https://github.com/merbanan/rtl_433|
344 186 laforge
|randio|Random number generator|Michel Pelletier|https://github.com/michelp/randio|
345 186 laforge
|gr-wmbus|m-bus (EN 13757-4) RX|oWCTejLVlFyNztcBnOoh|https://github.com/oWCTejLVlFyNztcBnOoh/gr-wmbus|
346 186 laforge
|ec3k|EnergyCount 3000 RX|Tomaž Šolc|https://github.com/avian2/ec3k|
347 186 laforge
|RTLSDR-Scanner|Radio Scanner|EarToEarOak|https://github.com/EarToEarOak/RTLSDR-Scanner|
348 186 laforge
|simple_ra|Radio Astronomy App|Marcus Leech|https://cgran.org/wiki/simple_ra|
349 186 laforge
|rtlizer|Spectrum analyzer|Alexandru Csete|https://github.com/csete/rtlizer|
350 186 laforge
|FS20_decode|FS20 Decoder|Thomas Frisch|https://github.com/eT0M/rtl_sdr_FS20_decoder|
351 186 laforge
|OpenLTE|LTE Toolkit|Ben Wojtowicz|http://sourceforge.net/p/openlte/home/Home/|
352 186 laforge
|rtltcpaccess|DAB compatibility layer|Steve Markgraf|https://github.com/steve-m/rtltcpaccess|
353 186 laforge
|SDR-J|"Analog" SDR & DAB|Jan van Katwijk|http://www.sdr-j.tk|
354 186 laforge
|RTLTcpSource|source for redhawk SDR framework|Michael Ihde|"redhawk Docs page":http://redhawksdr.github.io/Documentation/ "RTLTcpSource":https://github.com/Axios-Engineering/acquisition-components|
355 186 laforge
|gortlsdr|Golang wrapper|Joseph Poirier|https://github.com/jpoirier/gortlsdr|
356 186 laforge
|gr-rds (fork)|RDS + WBFM receiver|Dimitrios Symeonidis et al|https://github.com/bastibl/gr-rds|
357 186 laforge
|NRF24-BTLE-Decoder|Decoder for 2.4 GHz NRF24 & Bluetooh LE|Omri Iluz|"Code":https://github.com/omriiluz/NRF24-BTLE-Decoder "Blog post":http://blog.cyberexplorer.me/2014/01/sniffing-and-decoding-nrf24l01-and.html|
358 186 laforge
|acarsdec|ACARS decoder|Thierry Leconte|http://sourceforge.net/projects/acarsdec/|
359 197 Hoernchen
|rtl-sdr-airband|air band reiceiver/ATIS|Wong Man Hang|https://github.com/microtony/RTLSDR-Airband|
360 186 laforge
361 186 laforge
362 193 laforge
Also take a look at the applications which use rtl-sdr [[gr-osmosdr:GrOsmoSDR#KnownApps|through gr-osmosdr]].
363 186 laforge
364 1 steve-m
Using our lib? Tell us! Don't? Tell us why! :)
365 1 steve-m
366 186 laforge
!rtl-sdr-gmr.png!
367 186 laforge
Multiple GMR-carriers can be seen in a spectrum view with the full 3.2 MHz bandwidth (at 3.2 MS/s).
368 185 zecke2
369 185 zecke2
h2. Credits
370 1 steve-m
371 1 steve-m
372 1 steve-m
rtl-sdr is developed by Steve Markgraf, Dimitri Stolnikov, and Hoernchen, with contributions by Kyle Keen, Christian Vogel and Harald Welte.
Add picture from clipboard (Maximum size: 48.8 MB)