Actions
- Table of contents
- Base Radio Controller CLI
Base Radio Controller CLI¶
There is a CLI (Command Line Interface) of the Dimetra_EBTS_Base_Radio_Controller which we are just
starting to explore.
Reference¶
BRC> help
get/set alarm_mask amask
get/set alarm_reports ar
get alarms a
get/set brc_kit_no brckit
get/set brc_rev_no brcrev
get/set brc_scratch brcscratch
get/set cabinet
get/set default_tx_power dtxpwr
dekey
get dsp_version dspver
get dsp_sanity sanity
get/set enet_id enet
get ex_ad exad
get/set ex_kit_no exkit
get/set ex_rev_no exrev
get/set ex_scratch exscratch
get/set exciter_scaling_factor exsf
get fwd_pwr fp
get/set fwd_wattmeter_scaling_factor fwsf
key
k_factor kf
get/set max_vswr mv
get/set max_wattmeter_vswr mwv
get pa_ad paad
get pa_coef pac
get/set pa_kit_no pakit
get/set pa_rev_no parev
get/set pa_scaling_factor pasf
get/set pa_scratch pascratch
get/set pctrl pc
get/set position
get ps_ad psad
pwr_glitch
get/set rear_serial rear_ser
get ref_pwr rp
get reset_info
get/set ref_wattmeter_scaling_factor rwsf
get rptr_status status
reset
get rom_ver rv
get rptr_status status
get rssi
get/set rx_freq rxfreq
get/set rx_fru_config rxfru
get/set rx_inj rxinj
get/set rx_mode rxmode
get/set rx_qsign rxqsign
get rx_status rxstatus
get/set rx1_delta rx1delta
get/set rx2_delta rx2delta
get/set rx3_delta rx3delta
get/set rx1_kit_no rx1kit
get/set rx2_kit_no rx2kit
get/set rx3_kit_no rx3kit
get/set rx1_rev_no rx1rev
get/set rx2_rev_no rx2rev
get/set rx3_rev_no rx3rev
get/set rx1_scaling_factor rx1sf
get/set rx2_scaling_factor rx2sf
get/set rx3_scaling_factor rx3sf
get/set rx1_scratch rx1scratch
get/set rx2_scratch rx2scratch
get/set rx3_scratch rx3scratch
get second_level_pswd
get/set tetra_format tf
set tone
get/set training_interval ti
get/set txdc_i txdci
set txdc_i_final txdci_final
get/set txdc_q txdcq
set txdc_q_final txdcq_final
get/set tx_freq txfreq
get/set tx_if txif
set tx_power power
get/set txlin
set txlin_default txldef
get txlin_stat txlinstat
get/set txlin2
get txlin2_stat txlin2stat
get/set tx_test_mode
ver
get vswr
get wattmeter w
BSC>
dsp_version¶
BRC> get dsp_version DSP VERSION is 2.14 BRC> get tetra_format MCC : 0 MNC : 0 CC : 1 Downlink Type : 1 Uplink Type : 7 Trigger : off MS Power: 20 dBm ACC param: 203 dBm
tx_if¶
BRC> get txif TRANSMIT INTERMEDIATE FREQUENCY is 90.00000 MHz.
txlin¶
BRC> get txlin TXLIN[0x00]: 0x56 TXLIN[0x01]: 0x08 TXLIN[0x02]: 0x15 TXLIN[0x03]: 0x3E TXLIN[0x04]: 0xF1 TXLIN[0x05]: 0x1E TXLIN[0x06]: 0x2C TXLIN[0x07]: 0x00 TXLIN[0x08]: 0x3A TXLIN[0x09]: 0xBB TXLIN[0x0A]: 0x53 TXLIN[0x0B]: 0x80 TXLIN[0x0C]: 0xA3 TXLIN[0x0D]: 0x06 TXLIN[0x0E]: 0x04 TXLIN[0x0F]: 0x0C TXLIN[0x10]: 0x38 TXLIN[0x11]: 0x08 TXLIN[0x12]: 0x00 TXLIN[0x13]: 0x1F TXLIN[0x14]: 0x40 TXLIN[0x15]: 0x13 TXLIN[0x16]: 0xFF TXLIN[0x17]: 0x00 TXLIN[0x18]: 0x00 TXLIN[0x19]: 0x02 TXLIN[0x1A]: 0x00 BRC> get txlin2 TXLIN2[0x00]: 0x56 TXLIN2[0x01]: 0x08 TXLIN2[0x02]: 0x55 TXLIN2[0x03]: 0x3E TXLIN2[0x04]: 0xF1 TXLIN2[0x05]: 0x1E TXLIN2[0x06]: 0x2C TXLIN2[0x07]: 0x00 TXLIN2[0x08]: 0x3A TXLIN2[0x09]: 0xBB TXLIN2[0x0A]: 0x53 TXLIN2[0x0B]: 0x80 TXLIN2[0x0C]: 0xA3 TXLIN2[0x0D]: 0x06 TXLIN2[0x0E]: 0x04 TXLIN2[0x0F]: 0x0C TXLIN2[0x10]: 0x38 TXLIN2[0x11]: 0x08 TXLIN2[0x12]: 0x00 TXLIN2[0x13]: 0x1F TXLIN2[0x14]: 0x7F TXLIN2[0x15]: 0x13 TXLIN2[0x16]: 0xFF TXLIN2[0x17]: 0x00 TXLIN2[0x18]: 0x00 TXLIN2[0x19]: 0x02 TXLIN2[0x1A]: 0x00 BRC> get txlin_stat Checksum: 1566 Test Register : 0x2 Clip Detect Bit OFF Local Osc. Locked I - Channel Software Offset Bit not set Q - Channel Software Offset Bit not set Level Set : 0xff Sine Value : 0x89 Cosine Value : 0x0
this seems like filter taps for a digital linearization filter in the DSP?
default_tx_power¶
BRC> get default_tx_power
DEFAULT TRANSMITTER POWER is 40.00 watts ( 46.02 dBm )
BRC> set dtxpwr 2
FORMAT: set default_tx_power { 2.5 -> 40.0 }
BRC> set dtxpwr 2.5
Warning: Request to write to EEPROM denied due to insufficient permissions.
max_vswr¶
BRC> get max_vswr MAXIMUM VSWR is 4.00:1 BRC> set max_vswr 1.1 set MAX VSWR to 1.1 in RAM Warning: Request to write to EEPROM denied due to insufficient permissions.
wattmeter¶
BRC> get wattmeter BRC> RD POWER AT WATTMETER is 5.6 Watts [37.5 dBm] BRC> CTED POWER AT WATTMETER is 1.7 Watts [32.4 dBm] BRC> ETER VSWR is 3.49:1
tx_freq¶
BRC> get tx_freq TRANSMIT FREQUENCY is 427.50000 MHz
training_interval¶
BRC> get ti TRAINING INTERVAL is 90000 ticks (15 min)
rx_mode¶
BRC> get rx_mode RECEIVER 1 ENABLED RECEIVER 2 ENABLED RECEIVER 3 ENABLED
rx_status¶
BRC> get rx_status BER STATUS is LOCKED RECEIVER Q SIGN is NON-INVERTED RECEIVER 1 ENABLED RECEIVER 2 ENABLED RECEIVER 3 ENABLED RECEIVER INJECTION is HIGH
paad¶
BRC> get paad PA A->D PORTr0 = 0x0 [0.00v]. PA A->D PORTr1 = 0x0 [0.00v]. PA A->D PORTr2 = 0x2 [0.04v]. PA A->D PORTr3 = 0x80 [2.48v]. PA A->D PORTr4 = 0x9 [0.17v]. PA A->D PORTr5 = 0xd [0.25v]. PA A->D PORTr6 = 0x1 [0.06v]. PA A->D PORTr7 = 0x1 [0.06v]. PA A->D PORTr8 = 0x9 [0.17v]. PA A->D PORTr9 = 0x80 [2.48v]. PA A->D PORTr10 = 0x1 [0.04v]. PA A->D PORTr11 = 0x80 [2.50v].
This seems to be the ADC readings of the PA power supply
forwrd_power¶
BRC> get fp FORWARD POWER is 0 watts [-Inf dbm]
tx_freq¶
BRC> get tx_freq TRANSMIT FREQUENCY is 427.50000 MHz
exciter_ad¶
BRC> get ex_ad EXCITER A->D PORTr0 = 0x68 [13.71v]. EXCITER A->D PORTr1 = 0x5 [0.08v]. EXCITER A->D PORTr2 = 0xa1 [9.84v]. EXCITER A->D PORTr3 = 0xff [4.98v]. EXCITER A->D PORTr4 = 0x7b [4.80v]. EXCITER A->D PORTr5 = 0x27 [0.76v]. EXCITER A->D PORTr6 = 0x43 [1.31v]. EXCITER A->D PORTr7 = 0x0 [0.00v]. EXCITER A->D PORTr8 = 0x80 [5.00v]. EXCITER A->D PORTr9 = 0x8 [0.08v]. EXCITER A->D PORTr10 = 0x3 [0.03v]. EXCITER A->D PORTr11 = 0x80 [2.50v].
ex_kit_no¶
BRC> get ex_kit_no EXCITER KIT NUMBER is CTX5062B
tetra_format¶
BRC> get tetra_format MCC : 0 MNC : 0 CC : 1 Downlink Type : 1 Uplink Type : 7 Trigger : off MS Power: 20 dBm ACC param: 203 dBm BRC> set tetra_format 262 42 1 1 7 off 20 203 The value entered for MS power was not valid. 15 dBm is the default setting and has been used. MCC : 262 MNC : 42 CC : 1 Downlink Type : 1 Uplink Type : 7 Trigger : off MS Power: 20 dBm ACC param: 203 dBm
rptr_status¶
BRC> get rptr_status
************************************************************
BRC CODE VERSION D07.00.20-TETRA-BRC-ROM
OUTPUT PORT 0 = 0x808604
INPUT PORT 0 = 0xc9881f
INPUT PORT 1 = 0x808604
NUMBER WORKING RECEIVERS DETECTED : 3.
RX1 PRESENT...
RX2 PRESENT...
RX3 PRESENT...
BAND : TETRA {430 MHz}
RX FREQUENCY : 417.50000
TX FREQUENCY : 427.50000
TX IF FREQUENCY : 90.00000 MHz.
WINDOW CLIPPING LEVEL: 5.500000 db.
WINDOW CLIPPING SATURATION LEVEL: 15.000000 db.
WINDOW CLIPPING MODE: ON
SGC STATUS : ENABLED
SGC DELAY : 0 units = 0.000000 msec. [msec = units/120]
PERIODIC TRAINING DISABLED. [900 SECONDS].
POWER LEVELING DISABLED. [300 SECONDS].
RF POWER REPORTS DISABLED.
RF ALARM REPORTS DISABLED.
POWER WATCHDOG ENABLED.
INITILIZATION TRACE DISABLED.
ALARM MASK : |ff|ff|ff|ff|ff|ff|ff|ff|ff|ff|ff|ff|ff|ff|ff|ff|
Updated by laforge almost 8 years ago · 4 revisions
