Project

General

Profile

OsmoTRX » History » Version 27

ttsou, 02/19/2016 10:47 PM

1 1 ttsou
= OsmoTRX =
2
3
OsmoTRX is a software-defined radio transceiver that implements the Layer 1 physical layer of a BTS comprising the following 3GPP specifications:
4
 * TS 05.01 "Physical layer on the radio path"
5
 * TS 05.02 "Multiplexing and Multiple Access on the Radio Path"
6
 * TS 05.04 "Modulation"
7
 * TS 05.10 "Radio subsystem synchronization"
8
9 27 ttsou
OsmoTRX is based on the OpenBTS transceiver, but setup to operate independently with the purpose of using with non-OpenBTS software and projects. Currently there are numerous features contained in OsmoTRX that extend the functionality of the OpenBTS transceiver. These features include enhanced support for embedded platforms - notably ARM - and dual channel diversity support for the Fairwaves UmTRX. Most of these features will eventually be merged into mainline OpenBTS, but development will occur primarily on OsmoTRX.
10 6 ttsou
11
== Features ==
12
13 16 ttsou
'''Intel SSE Support'''
14 6 ttsou
* SSE3
15
* SSE4.1
16
17 20 ttsou
On Intel processors, OsmoTRX makes heavy use of the Streaming SIMD Extensions (SSE) instruction set. Accelerated operations include pulse shape filtering, resampling, sequence correlation, and many other signal processing operations. SSE3 is the minimum requirement for accelerated use.
18 1 ttsou
19 26 ttsou
SSE3 is present in the majority of Intel processors since later versions of the Pentium 4 architecture and is also present on low power Atom processors. Support is automatically detected at build time. For additional performance information, please see the performance and benchmarks section.
20 20 ttsou
21 16 ttsou
'''ARM NEON Support'''
22 6 ttsou
* NEON
23 1 ttsou
* NEON-VFPv4
24 6 ttsou
25 20 ttsou
OsmoTRX runs on a variety of ARM processors with and without NEON coprocessors. Like SSE on Intel processors, NEON provides acceleration with SIMD vectorized instructions.
26 1 ttsou
27 20 ttsou
Tested popular architectures include ARM11 (Raspberry Pi), Cortex-A8 (!BeagleBoard), and Cortex-A15 (!ArndaleBoard). Loosely speaking, these platforms are representative of low cost embedded devices, mid-level handsets, and high-end smartphones respectively. Similarly, in order, these platforms include no NEON coprocessor, standard NEON, and NEON-VFPv4. The latter NEON variation, VFPv4, provides additional fused-multiply-accumulate (FMA) instructions useful for many DSP operations.
28
29 26 ttsou
NEON support must be enabled by the user at build time. For additional information, please see the configuration and performance and benchmarks sections.
30 20 ttsou
31 6 ttsou
'''Dual Channel (UmTRX only)'''
32 7 ttsou
33
Two dual channel modes are available: standard dual channel mode and diversity. In standard dual channel mode, each RF
34
path of the dual channel device - currently only UmTRX - supports a different ARFCN. Each path operates independently a
35
nd operates similarly to two separate devices. GSM channel capacity in this mode is doubled.
36 1 ttsou
37 8 ttsou
'''Dual Channel Diversity (UmTRX only)'''
38 1 ttsou
39 20 ttsou
Diversity mode is similar to the standard dual channel mode except each antenna supports both ARFCN channels. In this case, the receiver sample bandwidth is widened to handle both ARFCN's and subsequently converted and demultiplexed into separate sample streams. Each GSM receive path is fed dual signals, where antenna selection diversity is performed by taking the stronger signal on a burst-by-burst basis.
40 16 ttsou
41 20 ttsou
Limitations are increased CPU utilization and that ARFCN spacing is restricted (currently at 400 kHz) by the receiver sampling bandwidth. Setting the ARFCN spacing beyond the sampling limit will disable the diversity path.
42
43 16 ttsou
'''Low Phase Error Modulator'''
44
45 1 ttsou
The default GSM downlink signal is configured for low distortion using a linearized GMSK modulator. The implementation is based on a two pulse Laurent approximation of continuous phase modulated (CPM) signals. The baseband output signal measures with very low phase error and is capable of passing industry spectrum mask requirements. Please note that actual performance will depend strongly on the particular device in use.
46 27 ttsou
47
Theoretical details can be found in the report on [http://tsou.cc/gsm/report_gmsk.pdf GMSK]. Octave / Matlab code for [http://tsou.cc/gsm/laurent.m pulse generation] is also available.
48 16 ttsou
49 20 ttsou
Very Low Phase Error (Ettus Research N200)
50 1 ttsou
51
[[Image(http://tsou.cc/gsm/osmo-trx-phase75.gif)]]
52
53 21 ttsou
Spectrum Mask (Ettus Research N200)
54 1 ttsou
55
[[Image(http://tsou.cc/gsm/osmo-trx-spectrum75.gif)]]
56
57 20 ttsou
== RF Hardware support ==
58 1 ttsou
59 20 ttsou
Multiple RF devices are currently supported. These include USRP family products from Ettus Research, and the UmTRX from Fairwaves.
60 1 ttsou
61 20 ttsou
||'''Fairwaves'''||'''Notes'''||
62
||UmTRX||Dual channel||
63
64
All Ettus Research devices are supported.
65
66
||'''Ettus Research'''||'''Notes'''||
67
||USRP1||Requires legacy libusrp driver and clocking modification||
68
||USRP2||10 MHz external reference required||
69 1 ttsou
||B100||
70
||B110||
71 20 ttsou
||B200||10 MHz external reference recommended||
72
||B210||* Dual channel, 10 MHz external reference recommended||
73 1 ttsou
||N200||
74
||N210||
75
||E100||
76
||E110||
77
78 20 ttsou
* Ettus B210 dual channel support with OsmoTRX is currently unavailable, but is expected to be added at a later time.
79
80 1 ttsou
== Embedded Platform Support ==
81
82 20 ttsou
OsmoTRX has been tested on the multiple embedded platforms representing a wide range of device types. Low cost ARM devices are generally limited by memory and I/O as much CPU utilization.
83 1 ttsou
84 20 ttsou
Running a full or near full ARFCN configuration (7 simultaneous TCH channels with Combination V) may require running the GSM stack remotely, which can be configured at runtime on the command line. This limitation appears to be scheduling related more so than lack of CPU resources, and may be resolved at a later time.
85
86
||'''Platform'''||'''SoC'''||'''Processor'''||'''SIMD/FPU'''||'''Testing Notes'''
87
||!ArndaleBoard||Samsung Exynos 5250||ARM Cortex-A15||NEON-VFPv4||7 TCH||
88 21 ttsou
||!BeagleBoard-xM||Texas Instruments OMAP3||ARM Cortex-A8||NEON||7 TCH, remote OsmoBTS stack||
89
||Ettus E100||Texas Instruments OMAP3||ARM Cortex-A8||NEON||7 TCH, remote OsmoBTS stack||
90
||Raspberry Pi||Broadcom BCM2835||ARM11||VFP||2 TCH, remote OsmoBTS stack||
91 1 ttsou
||Shuttle PC||NA||Intel Atom D2550||SSE3||Dual channel, 15 TCH||
92 20 ttsou
93 25 ttsou
All embedded plaforms were tested with low-phase error modulator disabled. Use of the more accurate modulator on embedded platforms has not been extensively tested.
94 19 ttsou
95
== Mailing List ==
96 18 ttsou
97 1 ttsou
For development purposes, OsmoTRX is discussed on both OpenBTS and OpenBSC mailing lists at openbts-discuss@lists.sourceforge.net and openbsc@lists.osmocom.org respectively.
98
99 22 ttsou
Please direct questions and bug reports to the list appropriate for the GSM stack being used.
100 19 ttsou
101 16 ttsou
Subscription information is available at [https://lists.sourceforge.net/lists/listinfo/openbts-discuss] and [http://lists.osmocom.org/mailman/listinfo/openbsc/].
102 19 ttsou
103
== GPRS support ==
104 16 ttsou
105 1 ttsou
OsmoTRX supports GPRS through OsmoBTS.
106 16 ttsou
107 1 ttsou
For GPRS support with OpenBTS, please use the transceiver supplied with OpenBTS.
108
109
== Source code ==
110 16 ttsou
111 1 ttsou
The source code is available from git.osmocom.org (module osmo-trx).
112
113
Public read-only access is available via
114 18 ttsou
 git clone git://git.osmocom.org/osmo-trx
115 1 ttsou
You can browse it via cgit: http://cgit.osmocom.org/cgit/osmo-trx/
116 18 ttsou
117
== Configuration and Build ==
118 19 ttsou
119 1 ttsou
The only package dependency is the Universal Hardware Driver (UHD), which is available from Ettus Research or Fairwaves depending on the device. Please note that the UHD implementation must match hardware (i.e. Ettus Research UHD for USRP devices and Fairwaves UHD with UmTRX). The one device that does not use the UHD driver is the USRP1, which is supported through the legacy libusrp driver provided in GNU Radio 3.4.2.
120
121 18 ttsou
'''Intel Platforms (All)'''
122
123
Intel SSE support is automatically detected on Intel x86 platforms. No user intervention is necessary. The general configuration defaults to the low phase error modulator. Atom users may wish to use the low-CPU utilization modulator, which can be later enabled from the command line at runtime.
124
{{{
125
$ ./configure
126
...
127 1 ttsou
checking whether mmx is supported... yes
128 18 ttsou
checking whether sse is supported... yes
129
checking whether sse2 is supported... yes
130
checking whether sse3 is supported... yes
131
checking whether ssse3 is supported... yes
132
checking whether sse4.1 is supported... yes
133 1 ttsou
checking whether sse4.2 is supported... yes
134 19 ttsou
...
135 18 ttsou
}}}
136
137
'''ARM Platforms with NEON'''
138
139
Many popular ARM development boards fall under this category including !BeagleBoard, !PandaBoard, and Ettus E100 USRP. This option will disable the low phase error modulator, which can be re-enabled at runtime. NEON support must be manually enabled.
140
{{{
141 19 ttsou
$ ./configure --with-neon
142 18 ttsou
}}}
143
144
'''ARM Platforms with NEON-VFPv4'''
145
146
Currently very few development platforms support this instruction set, which is seen mainly in high end smartphones and tablets. Available development boards are !ArndaleBoard and ODROID-XU. This option will disable the low phase error modulator, which can be re-enabled at runtime. NEON-VFPv4 support must be manually enabled.
147
{{{
148
$ ./configure --with-neon-vfpv4
149
}}}
150
151
'''ARM Platforms without NEON'''
152
153
This configuration mainly targets the Raspberry Pi. ARM platforms without NEON vector units are almost always very slow processors, and generally not very suitable for running OsmoTRX. Running OsmoTRX on a Raspberry Pi, however, is possible along with limited TCH (voice) channel support. Currently this configuration requires minor code changes.
154 1 ttsou
155 24 ttsou
Coming soon...
156 18 ttsou
157 16 ttsou
'''Build and Install'''
158
159
After configuration, installation is simple.
160
161
{{{
162 18 ttsou
$ make
163 19 ttsou
$ sudo make install
164 16 ttsou
}}}
165
166
== Running ==
167
168
OsmoTRX can be configured with a variety of options on the command line. In most cases, the default settings will suffice. Notable options include UHD device argument passing, which is often useful for using network based devices with firewalls, and external 10 MHz reference support.
169
170
{{{
171
$ osmo-trx -h
172
linux; GNU C++ version 4.8.1 20130603 (Red Hat 4.8.1-1); Boost_105300; UHD_003.005.004-140-gfb32ed16
173
174
Options:
175
  -h    This text
176
  -a    UHD device args
177
  -l    Logging level (EMERG, ALERT, CRT, ERR, WARNING, NOTICE, INFO, DEBUG)
178
  -i    IP address of GSM core
179
  -p    Base port number
180
  -d    Enable dual channel diversity receiver
181
  -x    Enable external 10 MHz reference
182
  -s    Samples-per-symbol (1 or 4)
183
  -c    Number of ARFCN channels (default=1)
184
}}}
185
186
{{{
187
$ osmo-trx -a "addr=192.168.10.2"
188
linux; GNU C++ version 4.8.1 20130603 (Red Hat 4.8.1-1); Boost_105300; UHD_003.004.000-b14cde5
189
190
Config Settings
191
   Log Level............... INFO
192
   Device args............. addr=192.168.10.2
193
   TRX Base Port........... 5700
194 1 ttsou
   TRX Address............. 127.0.0.1
195 16 ttsou
   Channels................ 1
196 1 ttsou
   Samples-per-Symbol...... 4
197
   External Reference...... Disabled
198 16 ttsou
   Diversity............... Disabled
199
200
-- Opening a UmTRX device...
201
-- Current recv frame size: 1472 bytes
202
-- Current send frame size: 1472 bytes
203
-- Setting UmTRX 4 SPS
204 19 ttsou
-- Transceiver active with 1 channel(s)
205 13 ttsou
}}}
206 19 ttsou
207
== Benchmarks ==
208 17 ttsou
209 13 ttsou
A variety of performance benchmarks are available for various code optimizations. These include floating point - integer conversions, convolution, and convolutional decoding. Note that convolutional decoding does not take place in OsmoTRX, but one stop higher in the Layer 1 stack - either in OsmoBTS or OpenBTS core.
210
211 1 ttsou
Selected benchmark results are provided below. All tests are run on a single core only.
212 24 ttsou
213
The benchmark code repository is coming soon...
214 13 ttsou
215
'''Intel Haswell (i7 4770K 3.5 GHz)'''
216
217
{{{
218 10 ttsou
--- Floating point to integer conversions
219
-- Testing 40000 iterations of 3120 values
220 1 ttsou
- Measuring conversion time
221
- Elapsed time base...                  0.065508 secs
222
- Validating SIMD conversion results... PASS
223
- Measuring conversion time
224
- Elapsed time SIMD ...                 0.011424 secs
225
- Speedup...                            5.734244
226
}}}
227
228
{{{
229
[+] Testing: GSM TCH/AFS 7.95 (recursive, flushed, punctured)
230
[.] Input length  : ret = 165  exp = 165 -> OK
231
[.] Output length : ret = 448  exp = 448 -> OK
232 3 ttsou
[.] Pre computed vector checks:
233
[..] Encoding: OK
234
[..] Decoding base: 
235
[..] Decoding SIMD: 
236
[..] Code N 3
237
[..] Code K 7
238
OK
239
[.] Random vector checks:
240
[.] Testing baseline:
241
[..] Encoding / Decoding 10000 cycles:
242
[.] Elapsed time........................ 1.435066 secs
243
[.] Rate................................ 3.121808 Mbps
244 1 ttsou
[.] Testing SIMD:
245
[..] Encoding / Decoding 10000 cycles:
246 17 ttsou
[.] Elapsed time........................ 0.073524 secs
247 1 ttsou
[.] Rate................................ 60.932485 Mbps
248
[.] Speedup............................. 19.518334
249
}}}
250
251 17 ttsou
'''Intel Atom (D2500 1.86 GHz)'''
252
{{{
253
--- Floating point to integer conversions
254
-- Testing 40000 iterations of 3120 values
255
- Measuring conversion time
256
- Elapsed time base...                 1.147449 secs
257
- Validating SSE conversion results... PASS
258
- Measuring conversion time
259
- Elapsed time SSE ...                 0.347838 secs
260
- Quotient...                          3.298803
261
}}}
262
263
{{{
264
[+] Testing: GSM TCH/AFS 7.95 (recursive, flushed, punctured)
265
[.] Input length  : ret = 165  exp = 165 -> OK
266
[.] Output length : ret = 448  exp = 448 -> OK
267
[.] Pre computed vector checks:
268
[..] Encoding: OK
269
[..] Decoding base: 
270
[..] Decoding SIMD: 
271
[..] Code N 3
272 1 ttsou
[..] Code K 7
273
OK
274
[.] Random vector checks:
275 17 ttsou
[.] Testing baseline:
276
[..] Encoding / Decoding 10000 cycles:
277
[.] Elapsed time........................ 11.822688 secs
278
[.] Rate................................ 0.378932 Mbps
279
[.] Testing SIMD:
280
[..] Encoding / Decoding 10000 cycles:
281
[.] Elapsed time........................ 0.550423 secs
282 19 ttsou
[.] Rate................................ 8.139195 Mbps
283
[.] Speedup............................. 21.479277
284
}}}
285 17 ttsou
286
'''!ArndaleBoard (ARM Cortex-A15 1.7 GHz)'''
287
288
Please note that the Viterbi implementations on ARM is largely C based with speedup generated primarily through algorithm changes. In comparison, vector optimization on Intel platforms with SSE is currently much more aggressive, which explains the disparity on decoding performance.
289
290
{{{
291
--- Floating point to integer conversions
292
-- Testing 40000 iterations of 3120 values
293
- Measuring conversion time
294
- Elapsed time base...                 0.384097 secs
295
- Validating SSE conversion results... PASS
296
- Measuring conversion time
297
- Elapsed time SSE ...                 0.100877 secs
298
- Quotient...                          3.807578
299
}}}
300
301
{{{
302
[+] Testing: GSM TCH/AFS 7.95 (recursive, flushed, punctured)
303
[.] Input length  : ret = 165  exp = 165 -> OK
304
[.] Output length : ret = 448  exp = 448 -> OK
305
[.] Pre computed vector checks:
306
[..] Encoding: OK
307
[..] Decoding base: 
308
[..] Decoding SIMD: 
309
[..] Code N 3
310
[..] Code K 7
311
OK
312
[.] Random vector checks:
313
[.] Testing baseline:
314
[..] Encoding / Decoding 10000 cycles:
315
[.] Elapsed time........................ 5.371288 secs
316
[.] Rate................................ 0.834064 Mbps
317
[.] Testing SIMD:
318
[..] Encoding / Decoding 10000 cycles:
319
[.] Elapsed time........................ 1.016621 secs
320
[.] Rate................................ 4.406755 Mbps
321
[.] Speedup............................. 5.283471
322
}}}
323
324 3 ttsou
'''!BeagleBoard-xM (ARM Cortex-A8 800 MHz)'''
325
{{{
326
--- Floating point to integer conversions
327
-- Testing 40000 iterations of 3120 values
328
- Measuring conversion time
329
- Elapsed time base...                  6.292542 secs
330
- Validating SIMD conversion results... PASS
331
- Measuring conversion time
332
- Elapsed time SIMD ...                 0.839081 secs
333 5 ttsou
- Quotient...                           7.499326
334 3 ttsou
}}}
335
336
{{{
337 4 ttsou
[+] Testing: GSM TCH/AFS 7.95 (recursive, flushed, punctured)
338 3 ttsou
[.] Input length  : ret = 165  exp = 165 -> OK
339
[.] Output length : ret = 448  exp = 448 -> OK
340
[.] Pre computed vector checks:
341
[..] Encoding: OK
342
[..] Decoding base: 
343
[..] Decoding SIMD: 
344
[..] Code N 3
345
[..] Code K 7
346
OK
347
[.] Random vector checks:
348 1 ttsou
[.] Testing baseline:
349 3 ttsou
[..] Encoding / Decoding 10000 cycles:
350
[.] Elapsed time........................ 21.963257 secs
351
[.] Rate................................ 0.203977 Mbps
352
[.] Testing SIMD:
353
[..] Encoding / Decoding 10000 cycles:
354 1 ttsou
[.] Elapsed time........................ 3.083282 secs
355
[.] Rate................................ 1.452997 Mbps
356 17 ttsou
[.] Speedup............................. 7.123337
357 1 ttsou
}}}
358
359
== Authors ==
360
361 23 ttsou
OsmoTRX is currently developed and maintained by Thomas Tsou with support from Fairwaves, the Open Technology Institute, and Ettus Research. The code is derived from the OpenBTS project, which was originally developed by David Burgess and Harvind Samra at Range Networks.
Add picture from clipboard (Maximum size: 48.8 MB)