Project

General

Profile

Rtl-sdr » History » Version 191

laforge, 05/14/2019 09:35 AM
fix gr-osmosdr and osmo-sdr links

1 185 steve-m
{{>toc}}
2 1 steve-m
3 185 steve-m
h1. rtl-sdr
4 1 steve-m
5
6 185 steve-m
DVB-T dongles based on the Realtek RTL2832U can be used as a cheap SDR, since the chip allows transferring the raw I/Q samples to the host, which is officially used for DAB/DAB+/FM demodulation. The possibility of this has been discovered by Eric Fry ("History and Discovery of RTLSDR":http://rtlsdr.org/#history_and_discovery_of_rtlsdr). Antti Palosaari has not been involved in development of rtl-sdr.
7 1 steve-m
8 185 steve-m
9
h2. Specifications
10
11
12
The RTL2832U outputs 8-bit I/Q-samples, and the highest theoretically possible sample-rate is 3.2 MS/s, however, the highest sample-rate without lost samples that has been tested so far is 2.56 MS/s. The frequency range is highly dependent of the used tuner, *dongles that use the Elonics E4000 offer the widest possible range (see table below)*.
13
14 186 laforge
|*Tuner*|*Frequency range*|
15
|Elonics E4000|52 - 2200 MHz with a gap from 1100 MHz to 1250 MHz (varies)|
16
|Rafael Micro R820T|24 - 1766 MHz|
17
|Rafael Micro R828D|24 - 1766 MHz|
18
|Fitipower FC0013|22 - 1100 MHz (FC0013B/C, FC0013G has a separate L-band input, which is unconnected on most sticks)|
19
|Fitipower FC0012|22 - 948.6 MHz|
20
|FCI FC2580|146 - 308 MHz and 438 - 924 MHz (gap in between)|
21 1 steve-m
22 185 steve-m
h2. Supported Hardware
23
24
25 1 steve-m
*Note:* Many devices with EEPROM have 0x2838 as PID and RTL2838 as product name, but in fact all of them have an RTL2832U inside.[[br]]
26 188 steve-m
Realtek never released a chip marked as RTL2838 so far.
27 1 steve-m
The following devices are known to work fine with RTLSDR software:
28 43 steve-m
29 186 laforge
|*VID*|*PID*|*tuner*|*device name*|
30
|0x0bda|0x2832|all of them|Generic RTL2832U (e.g. hama nano)|
31
|0x0bda|0x2838|E4000|ezcap USB 2.0 DVB-T/DAB/FM dongle|
32
|0x0ccd|0x00a9|FC0012|Terratec Cinergy T Stick Black (rev 1)|
33
|0x0ccd|0x00b3|FC0013|Terratec NOXON DAB/DAB+ USB dongle (rev 1)|
34
|0x0ccd|0x00d3|E4000|Terratec Cinergy T Stick RC (Rev.3)|
35
|0x0ccd|0x00e0|E4000|Terratec NOXON DAB/DAB+ USB dongle (rev 2)|
36
|0x185b|0x0620|E4000|Compro Videomate U620F|
37
|0x185b|0x0650|E4000|Compro Videomate U650F|
38
|0x1f4d|0xb803|FC0012|GTek T803|
39
|0x1f4d|0xc803|FC0012|Lifeview LV5TDeluxe|
40
|0x1b80|0xd3a4|FC0013|Twintech UT-40|
41
|0x1d19|0x1101|FC2580|Dexatek DK DVB-T Dongle (Logilink VG0002A)|
42
|0x1d19|0x1102|?|Dexatek DK DVB-T Dongle (MSI [[DigiVox]] mini II V3.0)|
43
|0x1d19|0x1103|FC2580|Dexatek Technology Ltd. DK 5217 DVB-T Dongle|
44
|0x0458|0x707f|?|Genius TVGo DVB-T03 USB dongle (Ver. B)|
45
|0x1b80|0xd393|FC0012|GIGABYTE GT-U7300|
46
|0x1b80|0xd394|?|DIKOM USB-DVBT HD|
47
|0x1b80|0xd395|FC0012|Peak 102569AGPK|
48
|0x1b80|0xd39d|FC0012|SVEON STV20 DVB-T USB & FM|
49 42 Hoernchen
50 185 steve-m
People over at reddit "are collecting a list (v2)":http://www.reddit.com/r/RTLSDR/comments/s6ddo/rtlsdr_compatibility_list_v2_work_in_progress/ of other devices that are compatible.
51 2 steve-m
52 174 steve-m
If you find a device that is not yet in the device list but should be supported, please send the VID/PID and additional info (used tuner, device name) to our mailing list.
53 5 steve-m
54 186 laforge
This is the PCB of the ezcap-stick:
55
!ezcap_top.jpg!
56 1 steve-m
More pictures can be found "here":http://www.steve-m.de/pictures/rtl-sdr/.
57 2 steve-m
58 185 steve-m
h2. Software
59
60
61 157 steve-m
Much software is available for the RTL2832. Most of the user-level packages rely on the librtlsdr library which comes as part of the rtl-sdr codebase. This codebase contains both the library itself and also a number of command line tools such as rtl_test, rtl_sdr, rtl_tcp, and rtl_fm. These command line tools use the library to test for the existence of RTL2832 devices and to perform basic data transfer functions to and from the device.
62
63
Because most of the RTL2832 devices are connected using USB, the librtlsdr library depends on the libusb library to communicate with the device.
64 158 steve-m
65 181 steve-m
At the user level, there are several options for interacting with the hardware. The rtl-sdr codebase contains a basic FM receiver program that operates from the command line. The rtl_fm program is a command line tool that can initialize the RTL2832, tune to a given frequency, and output the received audio to a file or pipe the output to command line audio players such as the alsa aplay or the sox play commands. There is also the rtl_sdr program that will output the raw I-Q data to a file for more basic analysis.
66 1 steve-m
67
For example, the following command will do reception of commercial wide-band FM signals:
68
69 185 steve-m
<pre>
70 158 steve-m
rtl_fm -f 96.3e6 -M wbfm -s 200000 -r 48000 - | aplay -r 48k -f S16_LE
71 185 steve-m
</pre>
72 1 steve-m
73
On a Mac, a similar command that works is as follows. This assumes that the sox package is installed, 'port install sox':
74
75 185 steve-m
<pre>
76 1 steve-m
rtl_fm -f 90100000 -M wbfm -s 200000 -r 48000 - | play -r 48000 -t s16 -L -c 1  -
77 185 steve-m
</pre>
78 1 steve-m
79
If you want to do more advanced experiments, the GNU Radio collection of tools can be used to build custom radio devices. GNU Radio can be used both from a GUI perspective in which you can drag-and-drop radio components to build a radio and also programmatically where software programs written in C or Python are created that directly reference the internal GNU Radio functions.
80
81
The use of GNU Radio is attractive because of the large number of pre-built functions that can easily be connected together. However, be aware that this is a large body of software with dependencies on many libraries. Thankfully there is a simple script that will perform the installation but still, the time required can be on the order of hours. When starting out, it might be good to try the command line programs that come with the rtl-sdr package first and then install the GNU Radio system later.
82 158 steve-m
83 190 laforge
h3. Binary Builds
84
85
h4. Windows
86
87
While Osmocom in general is a very much Linux-centric development community, we are now finally publishing automatic weekly Windows binary builds for the most widely used Osmocom SDR related projects:  [[rtl-sdr:]] and [[osmo-fl2k:]].
88
89
You can find the binaries at
90
* https://ftp.osmocom.org/binaries/windows/osmo-fl2k/
91
* https://ftp.osmocom.org/binaries/windows/rtl-sdr/
92
93
The actual builds are done by @roox who is building them using MinGW on OBS, see
94
* https://build.opensuse.org/project/show/network:osmocom:mingw:mingw32 and
95
* https://build.opensuse.org/project/show/network:osmocom:mingw:mingw64
96
97
The status of the osmocom binary publish job, executed once per week from now on, can be found at https://jenkins.osmocom.org/jenkins/view/All%20no%20Gerrit/job/Osmocom-OBS_MinGW_weekly_publish/
98
99 189 laforge
h3. Source Code
100
101 157 steve-m
The rtl-sdr code can be checked out with:
102 185 steve-m
<pre>
103 2 steve-m
git clone git://git.osmocom.org/rtl-sdr.git
104 185 steve-m
</pre>
105 172 steve-m
106 185 steve-m
It can also be browsed via "cgit":http://cgit.osmocom.org/cgit/rtl-sdr/, and there's an official "mirror on github":https://github.com/steve-m/librtlsdr that also provides "packaged releases":https://github.com/steve-m/librtlsdr/releases.
107 48 horiz0n
108 1 steve-m
If you are going to "fork it on github" and enhance it, please contribute back and submit your patches to: osmocom-sdr at lists.osmocom.org
109
110 191 laforge
A [[gr-osmosdr:]] GNU Radio source block for [[OsmoSDR:]] *and rtl-sdr* is available. *Please install a recent gnuradio (>= v3.6.4) in order to be able to use it.*
111 29 horiz0n
112 187 laforge
h3. Building the software
113 185 steve-m
114
h4. rtlsdr library & capture tool
115
116
117
*You have to install development packages for libusb1.0* and can either use cmake or autotools to build the software.
118
119 1 steve-m
Please note: prior pulling a new version from git and compiling it, please do a "make uninstall" first to properly remove the previous version.
120 20 horiz0n
121 1 steve-m
Building with cmake:
122 185 steve-m
<pre>
123 1 steve-m
cd rtl-sdr/
124 33 steve-m
mkdir build
125 19 steve-m
cd build
126
cmake ../
127 1 steve-m
make
128
sudo make install
129
sudo ldconfig
130 185 steve-m
</pre>
131 1 steve-m
132 130 horiz0n
In order to be able to use the dongle as a non-root user, you may install the appropriate udev rules file by calling cmake with -DINSTALL_UDEV_RULES=ON argument in the above build steps.
133 185 steve-m
<pre>
134 1 steve-m
cmake ../ -DINSTALL_UDEV_RULES=ON
135 185 steve-m
</pre>
136 19 steve-m
137 1 steve-m
Building with autotools:
138 185 steve-m
<pre>
139 19 steve-m
cd rtl-sdr/
140 1 steve-m
autoreconf -i
141 130 horiz0n
./configure
142 1 steve-m
make
143 19 steve-m
sudo make install
144 1 steve-m
sudo ldconfig
145 185 steve-m
</pre>
146 1 steve-m
147
The built executables (rtl_sdr, rtl_tcp and rtl_test) can be found in rtl-sdr/src/.
148 130 horiz0n
149
In order to be able to use the dongle as a non-root user, you may install the appropriate udev rules file by calling
150 185 steve-m
<pre>
151 1 steve-m
sudo make install-udev-rules
152 185 steve-m
</pre>
153 169 Hoernchen
154 185 steve-m
[attachment:RelWithDebInfo.zip pre-built Windows version":http://lists.osmocom.org/mailman/listinfo/osmocom-sdr]
155 1 steve-m
156 164 horiz0n
157 185 steve-m
h4. Gnuradio Source
158 1 steve-m
159 185 steve-m
160
*The Gnu Radio source requires a recent gnuradio (>= v3.7 if building master branch or 3.6.5 when building gr3.6 branch) to be installed.*
161
162 177 steve-m
The source supports direct device operation as well as a tcp client mode when using the rtl_tcp utility as a spectrum server.
163 1 steve-m
164 27 horiz0n
Please note: prior pulling a new version from git and compiling it, please do a "make uninstall" first to properly remove the previous version.
165 1 steve-m
166 185 steve-m
Please note: you always should build & *install the latest version of the dependencies (librtlsdr in this case)* before trying to build the gr source. The build system of gr-osmosdr will recognize them and enable specific source/sink components thereafter.
167 164 horiz0n
168 185 steve-m
Building with cmake (as described in the [[GrOsmoSDR|gr-osmosdr wiki page]]):
169 1 steve-m
170 185 steve-m
<pre>
171 164 horiz0n
git clone git://git.osmocom.org/gr-osmosdr
172 1 steve-m
cd gr-osmosdr/
173 185 steve-m
</pre>
174 1 steve-m
175
If you are building for gnuradio 3.6 series, you have to switch to the gr3.6 branch as follows
176 185 steve-m
<pre>
177 1 steve-m
git checkout gr3.6
178 185 steve-m
</pre>
179 1 steve-m
180 166 horiz0n
then continue with
181 1 steve-m
182 185 steve-m
<pre>
183 1 steve-m
mkdir build
184 161 horiz0n
cd build/
185
cmake ../
186 185 steve-m
</pre>
187 161 horiz0n
188 1 steve-m
Now cmake should print out a summary of enabled/disabled components. You may disable certain components by following guidelines shown by cmake. Make sure the device of your interest is listed here. Check your dependencies and retry otherwise.
189 185 steve-m
<pre>
190 1 steve-m
-- ######################################################
191
-- # gr-osmosdr enabled components                         
192
-- ######################################################
193 161 horiz0n
--   * Python support
194
--   * Osmocom IQ Imbalance Correction
195 185 steve-m
--   * sysmocom [[OsmoSDR]]
196
--   * [[FunCube]] Dongle
197 1 steve-m
--   * IQ File Source
198
--   * Osmocom RTLSDR
199 161 horiz0n
--   * RTLSDR TCP Client
200
--   * Ettus USRP Devices
201 185 steve-m
--   * Osmocom [[MiriSDR]]
202
--   * [[HackRF]] Jawbreaker
203 1 steve-m
-- 
204
-- ######################################################
205
-- # gr-osmosdr disabled components                        
206
-- ######################################################
207
-- 
208
-- Building for version: 4c101ea4 / 0.0.1git
209
-- Using install prefix: /usr/local
210 185 steve-m
</pre>
211 1 steve-m
212
Now build & install
213 185 steve-m
<pre>
214 1 steve-m
make
215
sudo make install
216
sudo ldconfig
217 185 steve-m
</pre>
218 1 steve-m
219
NOTE: The osmocom source block (osmocom/RTL-SDR Source) will appear under 'Sources' category in GRC menu.
220
221
For initial tests we recommend the multimode receiver gnuradio companion flowgraph (see "Known Apps" table below).
222 79 horiz0n
223
You may find more detailed installation instructions in this recent "tutorial":http://blog.opensecurityresearch.com/2012/06/getting-started-with-gnu-radio-and-rtl.html.
224 1 steve-m
225 185 steve-m
226 1 steve-m
h4. Automated installation
227
228
229 79 horiz0n
Marcus D. Leech has kindly integrated the forementioned build steps into his gnuradio installation script at "This is the most user-friendly option so far.
230 189 laforge
h2. Mailing List
231 1 steve-m
232
233 189 laforge
We discuss both [[OsmoSDR]] as well as rtl-sdr on the following mailing list: [mailto:osmocom-sdr@lists.osmocom.org].
234 1 steve-m
235 189 laforge
You can subscribe and/or unsubscribe via the following link: https://lists.osmocom.org/mailman/listinfo/osmocom-sdr
236 1 steve-m
237 189 laforge
Please make sure to read the [[cellular-infrastructure:MailingListRules]] before posting.
238 185 steve-m
239
240 189 laforge
h3. Usage
241
242
h4. rtl-sdr
243
244
245 76 horiz0n
Example: To tune to 392.0 MHz, and set the sample-rate to 1.8 MS/s, use:
246 110 horiz0n
247 185 steve-m
<pre>
248 1 steve-m
./rtl_sdr /tmp/capture.bin -s 1.8e6 -f 392e6
249 185 steve-m
</pre>
250 74 horiz0n
251
to record samples to a file or to forward the data to a fifo.
252 1 steve-m
253 90 horiz0n
If the device can't be opened, make sure you have the appropriate rights to access the device (install udev-rules from the repository, or run it as root).
254
255 74 horiz0n
256 185 steve-m
h4. rtl_tcp
257
258
259 2 steve-m
Example:
260
261 185 steve-m
<pre>
262
rtl_tcp -a 10.0.0.2 [-p listen port (default: 1234)":http://www.sbrac.org/files/build-gnuradio].
263 3 steve-m
Found 1 device(s).
264 2 steve-m
Found Elonics E4000 tuner
265 6 steve-m
Using Generic RTL2832U (e.g. hama nano)
266 22 horiz0n
Tuned to 100000000 Hz.
267
listening...
268 185 steve-m
Use the device argument 'rtl_tcp=10.0.0.2:1234' in [[OsmoSDR]] (gr-osmosdr) source
269 115 horiz0n
to receive samples in GRC and control rtl_tcp parameters (frequency, gain, ...).
270 185 steve-m
</pre>
271 59 horiz0n
272 32 horiz0n
use the rtl_tcp=... device argument in gr-osmosdr source to receive the samples in GRC and control the rtl settings remotely.
273
274
This application has been successfully crosscompiled for ARM and MIPS devices and is providing IQ data in a networked ADS-B setup at a rate of 2.4MSps. The gr-osmosdr source is being used together with an optimized gr-air-modes version (see Known Apps below).
275 185 steve-m
It is also available as a package in [[OpenWRT]].
276 60 horiz0n
277 185 steve-m
A use case is described "here":https://sites.google.com/site/embrtlsdr/.
278 60 horiz0n
279 185 steve-m
280
h4. rtl_test
281 89 steve-m
282 185 steve-m
To check the possible tuning range (may heavily vary by some MHz depending on device and temperature), call
283 63 horiz0n
<pre>
284 1 steve-m
rtl_test -t
285
</pre>
286
287
To check the maximum samplerate possible on your machine, type (change the rate down until no sample loss occurs):
288
<pre>
289
rtl_test -s 3.2e6
290
</pre>
291
A samplerate of 2.4e6 is known to work even over tcp connections (see rtl_tcp above). A sample rate of 2.88e6 may work without lost samples but this may depend on your PC/Laptop's host interface.
292
293
h2. Using the data
294
295
296
To convert the data to a standard cfile, following GNU Radio Block can be used:[[br]]
297 186 laforge
!rtl2832-cfile.png!
298 1 steve-m
The GNU Radio Companion flowgraph (rtl2832-cfile.grc) is attached to this page. It is based on the FM demodulation flowgraph posted by Alistair Buxton "on this thread":http://thread.gmane.org/gmane.linux.drivers.video-input-infrastructure/44461/focus=44525.
299
300
Please note: for realtime operation you may use fifos (mkfifo) to forward the iq data from the capture utility to the GRC flowgraph.
301
302
You may use any of the the following gnuradio sources (they are equivalent):
303 186 laforge
[[br]][[br]]!osmosource.png![[br]]
304 1 steve-m
305
What has been successfully tested so far is the reception of "Broadcast FM and air traffic AM":https://www.cgran.org/browser/projects/multimode/trunk radio, "TETRA":http://tetra.osmocom.org/, "GMR":http://gmr.osmocom.org/, "GSM":http://svn.berlin.ccc.de/projects/airprobe/, "ADS-B":https://www.cgran.org/wiki/gr-air-modes and "POCSAG":https://github.com/smunaut/osmo-pocsag.
306
307
Tell us your success story with other wireless protocols in ##rtlsdr channel on freenode IRC network.
308 116 horiz0n
309 185 steve-m
310 128 horiz0n
h2. Known Apps
311
312
313 185 steve-m
The following 3rd party applications and libraries are successfully using either librtlsdr directly or the corresponding gnuradio source (gr-osmosdr):
314
315 186 laforge
|*Name*|*Type*|*Author*|*URL*|
316
|gr-pocsag|GRC Flowgraph|Marcus Leech|https://www.cgran.org/browser/projects/gr-pocsag/trunk|
317
|multimode RX (try first!)|GRC Flowgraph|Marcus Leech|https://www.cgran.org/browser/projects/multimode/trunk|
318
|simple_fm_rvc|GRC Flowgraph|Marcus Leech|https://www.cgran.org/browser/projects/simple_fm_rcv/trunk|
319
|python-librtlsdr|Python Wrapper|David Basden|https://github.com/dbasden/python-librtlsdr|
320
|pyrtlsdr|Python Wrapper|Roger|https://github.com/roger-/pyrtlsdr|
321
|rtlsdr-waterfall|Python FFT GUI|Kyle Keen|https://github.com/keenerd/rtlsdr-waterfall|
322
|Wireless Temp. Sensor RX|Gnuradio App|Kevin Mehall|https://github.com/kevinmehall/rtlsdr-433m-sensor|
323
|QtRadio|SDR GUI|Andrea Montefusco et al.|http://napan.ca/ghpsdr3/index.php/RTL-SDR|
324
|gqrx|SDR GUI|Alexandru Csete|https://github.com/csete/gqrx|
325
|rtl_fm|SDR CLI|Kyle Keen|merged in librtlsdr master|
326
|SDR#|SDR GUI|Youssef Touil|http://sdrsharp.com/ and "Windows Guide":http://rtlsdr.org/softwarewindows or "Linux Guide":http://rtlsdr.org/softwarelinux|
327
|tetra_demod_fft|Trunking RX|osmocom team|"osmosdr-tetra_demod_fft.py":http://cgit.osmocom.org/cgit/osmo-tetra/tree/src/demod/python/osmosdr-tetra_demod_fft.py and the "HOWTO":http://tetra.osmocom.org/trac/wiki/osmo-tetra#Quickexample|
328
|airprobe|GSM sniffer|osmocom team et al|http://git.gnumonks.org/cgi-bin/gitweb.cgi?p=airprobe.git|
329
|gr-smartnet (WIP)|Trunking RX|Nick Foster|http://www.reddit.com/r/RTLSDR/comments/us3yo/rtlsdr_smartnet/ "Notes from the author":http://www.reddit.com/r/RTLSDR/comments/vbxl0/attention_grsmartnet_users_or_attempted_users/|
330
|gr-air-modes|ADS-B RX|Nick Foster|https://www.cgran.org/wiki/gr-air-modes call with --rtlsdr option|
331
|Linrad|SDR GUI|Leif Asbrink (SM5BSZ)|http://www.nitehawk.com/sm5bsz/linuxdsp/hware/rtlsdr/rtlsdr.htm" DAGC changes were applied to librtlsdr master|
332
|gr-ais (fork)|AIS RX|Nick Foster, Antoine Sirinelli, Christian Gagneraud|https://github.com/chgans/gr-ais|
333
|GNSS-SDR|GPS RX (Realtime!)|Centre Tecnològic de elecomunicacions de Catalunya|"Documentation":http://www.gnss-sdr.org/documentation/gnss-sdr-operation-realtek-rtl2832u-usb-dongle-dvb-t-receiver and http://www.gnss-sdr.org/|
334
|LTE-Cell-Scanner|LTE Scanner / Tracker|James Peroulas, Evrytania LLC|http://www.evrytania.com/lte-tools https://github.com/Evrytania/LTE-Cell-Scanner]|
335
|LTE-Cell-Scanner OpenCL accelerated *(new)*|LTE Scanner / Tracker|Jiao Xianjun|https://github.com/JiaoXianjun/LTE-Cell-Scanner|
336
|Simulink-RTL-SDR|MATLAB/Simulink wrapper|Michael Schwall, Sebastian Koslowski, Communication Engineering Lab (CEL), Karlsruhe Institute of Technology (KIT)|http://www.cel.kit.edu/simulink_rtl_sdr.php|
337
|gr-scan|Scanner|techmeology|http://www.techmeology.co.uk/gr-scan/|
338
|kalibrate-rtl|calibration tool|Joshua Lackey, Alexander Chemeris, Steve Markgraf|https://github.com/steve-m/kalibrate-rtl "Windows build":http://rtlsdr.org/files/kalibrate-win-release.zip|
339
|pocsag-mrt|Multichannel Realtime ]Decoder|iZsh|https://github.com/iZsh/pocsag-mrt|
340
|adsb#|ADS-B RX|Youssef Touil, Ian Gilmour|http://sdrsharp.com/index.php/a-simple-and-cheap-ads-b-receiver-using-rtl-sdr|
341
|osmo-gmr-rtl|GMR1 RX|Dimitri Stolnikov|http://gmr.osmocom.org/trac/wiki/GettingStarted#RTLSDRdongles|
342
|rtl_adsb|ADS-B RX|Kyle Keen|comes with the library|
343
|dump1090|ADS-B RX|Salvatore Sanfilippo|https://github.com/antirez/dump1090|
344
|rtl_433|Temperature Sensor Receiver|Benjamin Larsson|https://github.com/merbanan/rtl_433|
345
|randio|Random number generator|Michel Pelletier|https://github.com/michelp/randio|
346
|gr-wmbus|m-bus (EN 13757-4) RX|oWCTejLVlFyNztcBnOoh|https://github.com/oWCTejLVlFyNztcBnOoh/gr-wmbus|
347
|ec3k|EnergyCount 3000 RX|Tomaž Šolc|https://github.com/avian2/ec3k|
348
|RTLSDR-Scanner|Radio Scanner|EarToEarOak|https://github.com/EarToEarOak/RTLSDR-Scanner|
349
|simple_ra|Radio Astronomy App|Marcus Leech|https://cgran.org/wiki/simple_ra|
350
|rtlizer|Spectrum analyzer|Alexandru Csete|https://github.com/csete/rtlizer|
351
|FS20_decode|FS20 Decoder|Thomas Frisch|https://github.com/eT0M/rtl_sdr_FS20_decoder|
352
|OpenLTE|LTE Toolkit|Ben Wojtowicz|http://sourceforge.net/p/openlte/home/Home/|
353
|rtltcpaccess|DAB compatibility layer|Steve Markgraf|https://github.com/steve-m/rtltcpaccess|
354
|SDR-J|"Analog" SDR & DAB|Jan van Katwijk|http://www.sdr-j.tk|
355
|RTLTcpSource|source for redhawk SDR framework|Michael Ihde|"redhawk Docs page":http://redhawksdr.github.io/Documentation/ "RTLTcpSource":https://github.com/Axios-Engineering/acquisition-components|
356
|gortlsdr|Golang wrapper|Joseph Poirier|https://github.com/jpoirier/gortlsdr|
357
|gr-rds (fork)|RDS + WBFM receiver|Dimitrios Symeonidis et al|https://github.com/bastibl/gr-rds|
358
|NRF24-BTLE-Decoder|Decoder for 2.4 GHz NRF24 & Bluetooh LE|Omri Iluz|"Code":https://github.com/omriiluz/NRF24-BTLE-Decoder "Blog post":http://blog.cyberexplorer.me/2014/01/sniffing-and-decoding-nrf24l01-and.html|
359
|acarsdec|ACARS decoder|Thierry Leconte|http://sourceforge.net/projects/acarsdec/|
360
361
362 1 steve-m
Also take a look at the applications which use rtl-sdr [[GrOsmoSDR#KnownApps|through gr-osmosdr]].
363 186 laforge
364 1 steve-m
Using our lib? Tell us! Don't? Tell us why! :)
365
366 186 laforge
!rtl-sdr-gmr.png!
367
Multiple GMR-carriers can be seen in a spectrum view with the full 3.2 MHz bandwidth (at 3.2 MS/s).
368 185 steve-m
369
h2. Credits
370 1 steve-m
371
372
rtl-sdr is developed by Steve Markgraf, Dimitri Stolnikov, and Hoernchen, with contributions by Kyle Keen, Christian Vogel and Harald Welte.
Add picture from clipboard (Maximum size: 48.8 MB)