E1 Interface Blocks » History » Revision 3
Revision 2 (laforge, 05/04/2018 08:33 PM) → Revision 3/4 (laforge, 05/04/2018 08:35 PM)
{{>toc}}
h1. E1 Interface Blocks
An E1 interface is typically split into a couple of different blocks
h2. Transformer / Magnetics
The transformer perfrorms galvanic isolation between the wires of the line/cable and the E1 interface circuit. Think of Ethernet, which follows the exact same principle.
h2. Line Interface Unit (LIU)
The LIU sits between the E1 controller and the magnetics
The LIU is responsible for
* converting the received ternary HDB3 encoding into a stream of binary bits
* converting to-be-transmitted binary bits into ternary HDB3 encoding
Sometimes, further functionality such as clock recovery, loopback, jitter attenuator, ... are built into the LIU.
h3. XRT59L91
An example for a very simple LIU is the "Exar XRT59L91":https://www.exar.com/ds/xrt59l91v100.pdf. It only contains
* Rx: receive equalizer, peak detector, LOS detector
* Tx: pulse shaping, output drivers
It doesn't even do any HDB3 encoding/decoding or clock recovery
h3. XRT82D20
An example for a medium complexity LIU is the "Exar XRT82D20":https://www.exar.com/ds/xrt82d20_v108_082806.pdf. It contains
* transmit side
** HDB3 encoder
** Tx pulse shaper for both 75 Ohms coax and 120 Ohms twisted pair
** line driver
* receiver side
** peak detector, data slicer, LOS detect (to digital output)
** data + timing recovery
** hdb3 decoder
* digital, local and remote loopback capability
Compared to the XRT59L91, the significant addition is the HDB3 en/decoders and the timing recovery.
h3. IDT82V2081
An example for an even more higher end LIU is the "IDT82V2081":https://zh.idt.com/document/dst/82v2081-datasheet. compared to the XRT82D20, it contains
* adaptive internal termination for rx and tx
* adaptive equalizer on receive side
* PRBS detector / generator
* ILBC detector / generator
* not only E1, but also T1 + J1 compatibility
* SPI or parallel bus control interface
We're using the IDT82V2081 in the osmo-e1-xcvr evaluation board.
Another example in this category is the "Dallas/Maxim DS21348":https://datasheets.maximintegrated.com/en/ds/DS21348-DS21Q348.pdf
h2. E1 Controller "framer"
The E1 controller is what implements
* frame (and multiframe) alignment
* CRC4 generation/verification
* HDLC processors for the individual timeslots
* interface with the host computer
Examples for such controllers are
* Siemens/Infineon FALC/DualFALCQuadFALC/OctalFALC, LIU + Framer + HDLC + parallel bus interface)
** - used in many BTS/telecom equipment, but also in Digium E1/T1 cards equipment. obsolete/EOL.
** *obsolete/EOL*
* "CologneChip HFC-E1":http://www.colognechip.com/hfc-e1.pdf CologneChip HFC-E1 (LIU + Framer + HDLC + DMA engine with PCI bus interface)
** used in PCI cards we used for original OpenBSC development with Siemens BS-11 BTS
** supported by mISDN
* "Exar XRT86VL30":https://www.exar.com/ds/86vl30t1_v101_121809.pdf (LIU + Framer + HDLC + DMA engine with intel/motorola parallel bus)
* "Dallas/Maxim DS26521":https://datasheets.maximintegrated.com/en/ds/DS26521.pdf (SPI or parallel bus, TDM Backplane)
