BS11Configuration » History » Version 9
laforge, 02/19/2016 10:47 PM
some more details about the power plug
1 | 9 | laforge | == Power Connection == |
---|---|---|---|
2 | |||
3 | The Hirschmann plug used for the power connection is called ''Hirschmann Leitungsdose CA 4 LD 09 ZS'' and has the product number |
||
4 | 932 362-100. |
||
5 | |||
6 | The pin-out is as follows: |
||
7 | * GND: your shealding/earth line (PE), German:yellow/green wire |
||
8 | * 1: phase (L), German: Brown wire |
||
9 | * 2: not connected |
||
10 | * 3: neutral (N), German: Blue wire |
||
11 | |||
12 | Please refer to the photograph of a fully wired plug attached at the bottom of this page. |
||
13 | |||
14 | == E1 Hardware interface == |
||
15 | 2 | laforge | |
16 | We are using a 120 Ohms balanced connection between the BS11 and a HFC-E1 card. |
||
17 | To configure the BS11 hardware correctly, you need to |
||
18 | * open the connection between pin 2 and 3 of the 4 jumpers below connector J01 |
||
19 | |||
20 | === Cable to RJ45 === |
||
21 | |||
22 | 8 | laforge | The E1 interface[s] of the BS-11 are on some strange BNC-related twinax plugs called "BR2" (Radiall product # 605006000), you can find the PDF data sheet of the connectors at [http://radiall.applixia.net/catalogue/resource?path=PRODUCT/PDF/TDS/coaxialconnectors/R605006000EN.pdf Radiall] and you can buy them online from [http://webradiall.applixia.net/buyonline?PN=R605006000&LANG=en&SUP=FARNELL this link] (which for Germany results in a hyperlink to [http://de.farnell.com/jsp/displayProduct.jsp?sku=4196995 this page of the Farnell webshop] where they cost EUR 16.51 each). |
23 | 7 | laforge | |
24 | 3 | laforge | * left Y01 PCM in (from BSC): RJ45 pin 4,5 |
25 | 1 | laforge | * Y02 PCM out (to BSC): RJ45 pin 1,2 |
26 | 7 | laforge | * Y03 PCM left open |
27 | * Y04 PCM left open |
||
28 | 2 | laforge | |
29 | 1 | laforge | == Configuration of BTSM Object == |
30 | |||
31 | * BS11 requires PCM30CRC4 64kBit/s no Subslots |
||
32 | * OM Layer on Timeslot 1 |
||
33 | * TEI for OM Layer default Siemens is 25 (but configurable in BS11 [wiki:LMT]) |
||
34 | |||
35 | * the following parameters are not configurable |
||
36 | * RSL Layer on Timeslot 1, too |
||
37 | * TEI for RSL is fixed in Siemens equipment |
||
38 | * TEI = 0 für TRX0 |
||
39 | * TEI = 1 für TRX1 |
||
40 | * Attention: if you select OM Layer TEI 0 oder 1, RSL can no longer be brought up |
||
41 | |||
42 | * Timeslots for TCHs |
||
43 | * TRX0: TS2 und TS3 |
||
44 | * TRX1: TS4 und TS5 |
||
45 | |||
46 | == E1 interface == |
||
47 | 2 | laforge | |
48 | 1 | laforge | LI Objekt: Line MULTIDROP |
49 | 4 | laforge | |
50 | 1 | laforge | Impedance 120 Ohm balanced to connect to HFC-E1 board |
51 | Additionally you will need to change some jumpers on the connector board |
||
52 | 4 | laforge | of BS11: |
53 | 5 | laforge | * dip-switch SW3: |
54 | * 1-4: off |
||
55 | * 5-8: on |
||
56 | * TB01: no jumper |
||
57 | * TB02: no jumper |
||
58 | * TB03: no jumper |
||
59 | * TB04: no jumper |
||
60 | 4 | laforge | |
61 | SW3 is the dip-switch underneath the connector board |
||
62 | TB0* are the four jumpers on the left hand side of the connector board. |
||
63 | 1 | laforge | |
64 | == Database == |
||
65 | 2 | laforge | |
66 | 1 | laforge | Important database settings: |
67 | |||
68 | * the database has to be downloaded from PC via E1 to BS11 |
||
69 | |||
70 | |||
71 | 6 | laforge | * BCCH channel combination Type 5 or 8 (including SDCCH for SMS) |
72 | * TCH combination 0 or 9 |
||
73 | 1 | laforge | {{{ |
74 | Cell config: Not hopping |
||
75 | No Concentric Cell = 0 |
||
76 | Radiomeasgran =254 |
||
77 | No Power Reduction = 0 |
||
78 | Excessive distance =0 disabled |
||
79 | }}} |