RBS6402 » History » Version 6
laforge, 09/14/2021 05:32 PM
add table of part numbers
| 1 | 1 | laforge | h1. RBS6402 |
|---|---|---|---|
| 2 | |||
| 3 | 2 | laforge | Contrary to the General/typical RBS6000 family, the RBS6402 is a small cell. It is not modular and doesn't consist of modules like DUL/RUS. It doesn't have any CPRI connections. It can support up to three radio modules and comes in a varity of different LTE bands. |
| 4 | |||
| 5 | 6 | laforge | h2. variants / part numbers |
| 6 | |||
| 7 | there are plenty of different variants out there: |
||
| 8 | |||
| 9 | |_.Part Number|_. Bands| |
||
| 10 | |KRD 901 060/1|B2/25 B4 B7| |
||
| 11 | |KRD 901 060/2|2x B2/25 B4 B7| |
||
| 12 | |KRD 901 060/3|B2/25 B4 B7 Wi-US| |
||
| 13 | |KRD 901 060/4|B2/25 B4 B7 Wi| |
||
| 14 | |KRD 901 060/5|2x B2/25 B4 B7 Wi-US| |
||
| 15 | |KRD 901 060/6|2x B2/25 B4 B7 Wi| |
||
| 16 | |KRD 901 060/7|B2/25| |
||
| 17 | |KRD 901 060/8|B4| |
||
| 18 | |KRD 901 060/9|B7| |
||
| 19 | |KRD 901 060/19|B1 B3(B9) B7| |
||
| 20 | |KRD 901 060/20|2x B1 B3(B9) B7| |
||
| 21 | |KRD 901 060/23|B1| |
||
| 22 | |KRD 901 060/24|B3/B9| |
||
| 23 | |KRD 901 060/39|B7 (ETSI)| |
||
| 24 | |KRD 901 060/80|LAA B2/25 B4 B7| |
||
| 25 | |KRD 901 060/83|B2 B4 B7 B25 B252 B255 (1900, 2100, 2600, 5200, 5700)| |
||
| 26 | |||
| 27 | 2 | laforge | |
| 28 | 1 | laforge | h2. connectors |
| 29 | |||
| 30 | h3. WAN B |
||
| 31 | |||
| 32 | this is a standard SFP connector, you can use any gigabit ethernet compatible MM or SM SFP module on it |
||
| 33 | |||
| 34 | h3. WAN A / PoE |
||
| 35 | |||
| 36 | Use a LTPoE++ capable 90W PoE injector here |
||
| 37 | |||
| 38 | h3. 48V |
||
| 39 | |||
| 40 | 4 | tnt | This is a standard 3.5mm terminal block. You can e.g. use a "Wurth Electronic 691361100002":https://octopart.com/691361100002-würth+elektronik-18818376 or "Phoenix contact MC 1,5/2-ST-3,5":https://octopart.com/1840366-phoenix+contact-6675 |
| 41 | 1 | laforge | |
| 42 | h3. Fan |
||
| 43 | |||
| 44 | The fan connector has two pins with +5V and two pins with GND. You can use a "Molex 43025-0408":https://octopart.com/43025-0408-molex-24935555 part to mate it. This is just the housing, you will need crimp contacts and matching crimp tool, or you use pre-crimped wires like "Molex 79758-0010":https://octopart.com/79758-0010-molex-24727080. |
||
| 45 | |||
| 46 | The two top pins (near the latch) are GND, while the two bottom pins (near the enclosure) are +5V. |
||
| 47 | 5 | laforge | |
| 48 | h2. factory reset button |
||
| 49 | |||
| 50 | On the back (connector) side, in one corner there is a black rubber cap over some kind of high density debug connector. You have to remove that rubber cap completely (not just the connector part) and will notice a pushbutton underneath the location where the rubber lid is fixed to the enclosure. |
