Colocated Hub » History » Version 19
laforge, 09/23/2022 08:12 AM
1 | 2 | laforge | {{>toc}} |
---|---|---|---|
2 | |||
3 | 1 | laforge | h1. Colocated Hub |
4 | |||
5 | 4 | laforge | This page exists to collect planning about the future colocated OCTOI hub, see #5542 |
6 | 2 | laforge | |
7 | 14 | laforge | h2. Block Diagrams |
8 | |||
9 | h3. E1/TDM network |
||
10 | |||
11 | {{graphviz_link() |
||
12 | graph G { |
||
13 | subgraph cluster_colo { |
||
14 | label = "Co-Located Hub"; |
||
15 | divf [label="DIVF\nCentral Switch",shape="house"]; |
||
16 | icE1usb; |
||
17 | pm3 [label="Livingston Portmaster 3"]; |
||
18 | as54 [label="Cisco AS5400"]; |
||
19 | icE1usb -- divf [label="E1 (timing master)"]; |
||
20 | pm3 -- divf [label="E1"]; |
||
21 | as54 -- divf [label="8xE1"]; |
||
22 | } |
||
23 | divf -- laforge [label="TDMoIP"]; |
||
24 | divf -- manawyrm [label="TDMoIP"]; |
||
25 | divf -- gruetzkopf [label="TDMoIP"]; |
||
26 | divf -- roox [label="TDMoIP"]; |
||
27 | divf -- DrDeke [label="TDMoIP"]; |
||
28 | etc [label="other users..."]; |
||
29 | divf -- etc [label="TDMoIP"]; |
||
30 | } |
||
31 | }} |
||
32 | |||
33 | 15 | laforge | h3. IP network |
34 | |||
35 | {{graphviz_link() |
||
36 | graph G { |
||
37 | subgraph cluster_colo { |
||
38 | label = "Co-Located Hub"; |
||
39 | vlan [label="VLAN/Switch",shape="rect"]; |
||
40 | divf [label="DIVF\nCentral Switch",shape="house"]; |
||
41 | apu [label="APU (hosting icE1usb)"]; |
||
42 | pm3 [label="Livingston Portmaster 3"]; |
||
43 | as54 [label="Cisco AS5400"]; |
||
44 | |||
45 | |||
46 | vlan -- divf; |
||
47 | vlan -- apu; |
||
48 | vlan -- pm3; |
||
49 | vlan -- as54; |
||
50 | } |
||
51 | lakshmi [label="Firewall\n(lakshmi)"]; |
||
52 | public_v4 [label="Internet (IPv4)"]; |
||
53 | public_v6 [label="Internet (IPv6)"]; |
||
54 | 17 | laforge | divf -- lakshmi [label="VLAN 257"]; |
55 | 15 | laforge | lakshmi -- public_v4; |
56 | lakshmi -- public_v6; |
||
57 | } |
||
58 | }} |
||
59 | 14 | laforge | |
60 | 4 | laforge | h2. Rackmount units |
61 | 1 | laforge | |
62 | 4 | laforge | h3. Central Office server (2U / 67cm) |
63 | 1 | laforge | |
64 | 4 | laforge | This is a 2U rack-mount server running all the relevant software. |
65 | 1 | laforge | |
66 | 4 | laforge | See [[AVSt_Server]] for more details of the server |
67 | 1 | laforge | |
68 | 4 | laforge | h4. Connections |
69 | 1 | laforge | |
70 | 4 | laforge | This is a 2U rack-mount server with the following connections: |
71 | * Power |
||
72 | 10 | laforge | ** 2x AC power connections (redundant PSU) |
73 | 4 | laforge | * Ethernet |
74 | ** 1x RJ45 100-Base-TX BMC |
||
75 | ** 2x RJ45 1000-Base-TX |
||
76 | * E1 |
||
77 | ** 8x E1 to a co-located Cisco AS5400 (see below) |
||
78 | ** 1x E1 to a co-located Livingston PM3 (see below) |
||
79 | ** 1x E1 to icE1usb/clock-source |
||
80 | 1 | laforge | |
81 | |||
82 | 4 | laforge | h3. icE1usb / E1 clock source (1U / 31cm) |
83 | 1 | laforge | |
84 | 4 | laforge | This is a 1U rack mount system containing: |
85 | * a PC-Engines APU3 embedded x86_64 |
||
86 | * an [[e1-t1-adapter:ICE40_E1_USB_interface|icE1usb]] with a custom RS422 interface board |
||
87 | * a custom rs422 over voltage protection + 12V injection board |
||
88 | 1 | laforge | |
89 | 4 | laforge | This icE1usb acts as a GPS-disciplined clock master. However, as no acutal RF GPS signal is available in the data centre, we are using an Ericsson [[ericsson-rbs-6xxx:GPS_02]] attached via ~100m of RS-422. |
90 | 1 | laforge | |
91 | 4 | laforge | h4. Connections |
92 | 1 | laforge | |
93 | 4 | laforge | * Power |
94 | ** 2x AC power connections (1x APU, 1x RS422/GPS) |
||
95 | * Ethernet |
||
96 | 8 | laforge | ** 1x RJ45 to internal VLAN |
97 | 4 | laforge | * RS422 |
98 | 1 | laforge | ** 1x RJ45 towards GPS02 on the roof |
99 | |||
100 | 4 | laforge | h3. Cisco AS5400 RAS Server (2U / 49cm) |
101 | 1 | laforge | |
102 | 4 | laforge | h4. Connections |
103 | 1 | laforge | |
104 | 4 | laforge | * Power |
105 | ** 2x AC power connection (redundant PSU) |
||
106 | * Ethernet |
||
107 | ** 1x RJ45 Ethernet (100-Base-TX) to internal VLAN |
||
108 | * E1 |
||
109 | ** 8x E1 (via break-out cable) to AVSt-Server |
||
110 | 7 | laforge | * RS232 |
111 | ** Serial console connection via USB-UART to [[AVSt_Server]] |
||
112 | 4 | laforge | |
113 | h3. Livingstion Portmaster 3 (2U / 31cm) |
||
114 | |||
115 | h4. Connections |
||
116 | |||
117 | * Power |
||
118 | ** 1x AC power connection |
||
119 | * Ethernet |
||
120 | 9 | laforge | ** 1x RJ45 Ethernet (10-Base-TX) [yes, 10MBps] to internal VLAN |
121 | 4 | laforge | * E1 |
122 | ** 1x E1 to AVSt-Server |
||
123 | 6 | laforge | * RS232 |
124 | ** Serial console connection via USB-UART to [[AVSt_Server]] |
||
125 | 4 | laforge | |
126 | h2. Roof installation |
||
127 | |||
128 | |||
129 | On the roof of the data centre, the CAT5 cable with RS422 for the GPS03 arrives. |
||
130 | |||
131 | It will be passed through several DIN rail mounted OVP (Over Voltage Protection) circuits before connecting to the actual DIN-rail mounted Ericsson GPS03 |
||
132 | |||
133 | The Ericsson GPS03 has a SMA connector, to which a SMA-male to N-Male coaxial cable is attached. |
||
134 | |||
135 | A Times Microwave LP-GTR-NFF lightning protector (N-female to N-femaile) is used to pass the coaxial cable through the enclosure |
||
136 | |||
137 | An external GPS antenna with N connector is plugged into the LP-GTR-NFF |
||
138 | 1 | laforge | |
139 | 5 | laforge | h3. Overview diagram |
140 | 1 | laforge | |
141 | 5 | laforge | This diagram illustrates the parts and connections on the rooftop. Rectangular objects are DIN-rail mounted. |
142 | 1 | laforge | |
143 | 5 | laforge | {{graphviz_link() |
144 | graph G { |
||
145 | subgraph cluster_1 { |
||
146 | label="Rooftop enclosure"; |
||
147 | rj45splitter [label="RJ45 splitter"]; |
||
148 | GPS03 [label="Ericsson GPS03", shape=rect]; |
||
149 | ovp_rs422_1 [shape=rect]; |
||
150 | ovp_rs422_2 [shape=rect]; |
||
151 | ovp_rs422_3 [shape=rect]; |
||
152 | ovp_12v [shape=rect]; |
||
153 | lp [label="LP-GTR-NFF"]; |
||
154 | rj45splitter -- ovp_rs422_1; |
||
155 | rj45splitter -- ovp_rs422_2; |
||
156 | rj45splitter -- ovp_rs422_3; |
||
157 | rj45splitter -- ovp_12v; |
||
158 | ovp_rs422_1 -- GPS03; |
||
159 | ovp_rs422_2 -- GPS03; |
||
160 | ovp_rs422_3 -- GPS03; |
||
161 | ovp_12v -- GPS03; |
||
162 | GPS03 -- lp [label="SMA-male/N-female"]; |
||
163 | } |
||
164 | antenna [label="GPS Antenna"]; |
||
165 | antenna -- lp [label="RG58 white / N-female"]; |
||
166 | rack [label="Rack in DC"]; |
||
167 | rack -- rj45splitter [label="CAT5"]; |
||
168 | } |
||
169 | }} |
||
170 | 2 | laforge | |
171 | 1 | laforge | h2. Software |
172 | |||
173 | 3 | laforge | * Like in the current hub at @laforge's basement, we should run the entire yate / osmo-e1d / dahdi-trunkdev inside a KVM with SRV-IO mapping the PCI devices |
174 | |||
175 | 16 | laforge | h2. Network |
176 | |||
177 | h2. Public IP |
||
178 | |||
179 | |_.Host|_.IPv4|_.IPv6|_.IPv4-internal| |
||
180 | |avst|213.95.46.30|?|192.168.7.129/25| |
||
181 | |divf|213.95.46.31|?|192.168.7.130/25| |
||
182 | |as5400|213.95.46.29|?|192.168.7.133| |
||
183 | |pm3|-|-|192.168.7.132| |
||
184 | |icE1-apu|-|-|192.168.7.131| |
||
185 | 19 | laforge | |grafana|-|-|192.168.7.134| |
186 | 16 | laforge | |avst-bmc|213.95.46.28|?|-| |
187 | 3 | laforge | |
188 | h2. Misc / TODO |
||
189 | |||
190 | h3. local verification with modem/ISDN-TA |
||
191 | |||
192 | It would be great if we could somehow verify local calls via the yate / hub excluding the complexity of the TDMoIP to compare calls without TDMoIP to calls with TDMoIP. |
||
193 | |||
194 | Unfortuantely I'm not aware of any really small PBX that would terminate the E1/S2M and offer S0/POTS ports. Adding antoher 3U for a PBX seems excessive. |
||
195 | |||
196 | 1 | laforge | Doing calls between PM3 and ASR5400 is of course an option, but ideally we'd have a real physical modem attached via a serial port, and a real HFC-S-USB for test purpose. |
197 | 11 | laforge | |
198 | h2. High-level parameters for data centre |
||
199 | |||
200 | * 7U rackspace |
||
201 | * 7x AC power outlet |
||
202 | 13 | laforge | * 7x Ethernet switch port (one of which supports 10 MBps!) |
203 | 11 | laforge | ** some ports in a new VLAN |
204 | ** some ports in an existing VLAN of my other servers in Rack 1120 |
||
205 | * 1x CAT5 between rack and roof |
||
206 | * about 10cm of space on DIN-rail on roof enclosure (to mount OVP + GPS03) |
||
207 | |||
208 | h2. Questions |
||
209 | 1 | laforge | |
210 | 12 | laforge | * Required antenna cable length between rooftop enclosure and antenna |
211 | * Mechanical antenna mounting details |
||
212 | 11 | laforge | * detailed switch port / VLAN config |