Siemens GSM-R Cab Radio » History » Version 3
laforge, 01/23/2023 06:35 PM
1 | 3 | laforge | {{>toc}} |
---|---|---|---|
2 | 1 | laforge | |
3 | 3 | laforge | h1. Siemens GSM-R CAB Radio |
4 | |||
5 | Osmocom has been provided with two ancient Siemens GSM CAB Radio devices, i.e. the kind of MS installed fixed into a train engine. |
||
6 | |||
7 | {{thumbnail(20230123_184656.jpg)}} |
||
8 | {{thumbnail(20230123_184637.jpg)}} |
||
9 | |||
10 | |||
11 | h2. Sub-Rack Hardware |
||
12 | |||
13 | {{thumbnail(20230123_184513.jpg)}} |
||
14 | |||
15 | |||
16 | h3. Backplane |
||
17 | |||
18 | At the back of the sub-rack there's a custom back-plane to interconnect the various modules |
||
19 | |||
20 | {{thumbnail(20230123_183101.jpg)}} |
||
21 | {{thumbnail(20230123_182917.jpg)}} |
||
22 | |||
23 | h3. High Voltage Power Supply Module |
||
24 | |||
25 | This is a fully encapsulated, passive cooled, DC/DC converter with |
||
26 | * Input voltage 65..150V |
||
27 | * Two output voltage rails of 12V / 4A |
||
28 | |||
29 | |||
30 | h3. 12V -> 5V DC/DC converter Module |
||
31 | |||
32 | This is a circuit board that generates a 5V rail from 12V |
||
33 | |||
34 | |||
35 | h3. GSM Modem Module |
||
36 | |||
37 | This is a module implementing the actual GSM-R modem. It consts of two circuit boards: One digital and one analog/RF. |
||
38 | |||
39 | h4. Digital Board |
||
40 | |||
41 | h4. RF Board |
||
42 | |||
43 | |||
44 | h3. PC/104 embedded PC Module |
||
45 | |||
46 | This is a carrier board hosting a PC/104 embedded x86 Mainboard. |
||
47 | |||
48 | h4. Carrier |
||
49 | |||
50 | h4. PC/104 x86 SBC |
||
51 | |||
52 | |||
53 | h3. I/O board |
||
54 | |||
55 | This is a board that brings signals from the backplane and frontplane and brings them to connectors towards the main connector panel. |
||
56 | |||
57 | |||
58 | h2. Handset Hardware |
||
59 | |||
60 | |||
61 | |||
62 | 1 | laforge | h2. Connector pinout |
63 | 2 | laforge | |
64 | h3. EXT RADIO (DB-15 female) |
||
65 | |||
66 | h3. SER I/O (DB-25 male) |
||
67 | |||
68 | h3. HMI 1 (DB-25 female) |
||
69 | |||
70 | h3. HMI 2 (DB-25 female) |
||
71 | |||
72 | h3. MVB OUT (DB-9 female) |
||
73 | |||
74 | h3. MVB IN (DB-9 female) |
||
75 | |||
76 | h3. ANT (N) |
||
77 | |||
78 | This a standdard 50-ohms N-type conector to connect to the GSM-R antenna. |
||
79 | |||
80 | 1 | laforge | h3. PMU (DB-9 male) |
81 | 2 | laforge | |
82 | 3 | laforge | This connector is forwarded internally to the DB-9 connector on the front of the embedded PC. Probably serial console. |
83 | 2 | laforge | |
84 | h3. TRAIN POWER AND I/O (circular connector) |
||
85 | 1 | laforge | |
86 | |_.Pin (ext)|_.Internal Connector|_.Internal Connector Pin|_.Wire color|_.Purpose| |
||
87 | |H|PL6|1|rose|| |
||
88 | |K|PL6|2|white|| |
||
89 | |M|PL6|3|green|| |
||
90 | |P|PL6|4|purple|| |
||
91 | |S|PL6|5|blue|| |
||
92 | |J|PL6|6|black|| |
||
93 | |L|PL6|7|red|| |
||
94 | |N|PL6|8|yellow|| |
||
95 | |R|PL6|9|orange|| |
||
96 | |B|PL6|10|green|| |
||
97 | |T|PL7|1|white|| |
||
98 | |d|PL7|2|green|| |
||
99 | |F|PL7|4|blue|| |
||
100 | |A|PL7|5|red|| |
||
101 | |U|PL7|6|rose|| |
||
102 | |e|PL7|7|blue|| |
||
103 | |G|PL7|9|grey|| |
||
104 | |C|PL7|10|yellow|| |
||
105 | |V|PL8|1|white|| |
||
106 | |D|PL8|3|purple|| |
||
107 | |W|PL8|4|red|| |
||
108 | |E|PL8|6|orange|| |
||
109 | |c|PL9|1|orange|| |
||
110 | |Z|PL9|2|rose|| |
||
111 | |X|PL9|3|green|| |
||
112 | |b|PL9|4|grey|| |
||
113 | |a|PL9|5|red|| |
||
114 | |Y|PL9|6|yellow|| |