Retronetworking

h1. Bintec X1200

The Bintec X1200 is a ISDN router featuring two ISDN BRI lines on the WAN side and a single ethernet connecton on the LAN side.

It apparently supports remote CAPI (CAPI over TCP).

h2. Hardware

* Motorola XPC860DTZP50D3 PowerPC processor

* Samsung K4S643232C-TC10 SDRAM

* Sharp LH28F016SCHT-L95 Flash

* Infineon PSB2115H V1.1 IPAC ISDN Interface IC

* Lucent LU3x31FT2J80 Ethernet Transceiver IC

* LevelOne LXT905LC Ethernet PHY

* Maxim MAX202ECWE RS232 trasnceiver IC

* Maxim DS1314S NVRAM controller IC

* 5.5V 1.0F supercap (for NVRAM)

h2. Serial Console

h3. Power up

<pre>

### X1200 (Hardware-Rev. 1.2, Firmware-Rev. 6.0) ###

CPU   Check ... passed (MPC 8XXT D3)

SDRAM Check ........ passed (8 MByte)

FLASH Check .. passed (2 MByte)

ISDN  Check ... passed

100BT Check ... passed

10BT  Check ... passed

### Selftest passed ###

Press <sp> for boot monitor or any other key to boot system

</pre>

h3. Bootmonitor

<pre>

X1200 Bootmonitor V.6.2 Rev. 8 from 2003/01/23 00:00:00

Copyright (c) 1999-2002 by BinTec Communications AG

(1) Boot System

(2) Software Update via TFTP

(3) Software Update via XMODEM

(4) Delete Configuration

(5) Default Bootmonitor Parameters

(6) Show System Information

Your Choice> 6

### Start System information ###

Identification:              BINTEC X1000

Hardware:                    1.2

Serial:                      X1B120000370449

Ethernet MAC 100BT:          00:a0:f9:02:4b:70

Flash:                        2047 K/byte

RAM:                          8127 K/byte

### Current Software

Logik:                       6.0

Bootmon:                     V.6.2 Rev. 8 from 2003/01/23 00:00:00

Boss:                        6.2.5

### more info

ID:                          X1B

Name:                        X1200

Company (short):             BINTEC

Type:                        X1200

Company (long):              BinTec Communications AG

Features:                    0

### End System information ###

<pre>

<pre>

Your Choice> 4

Deleting the configuration will reset your router to factory state.

Ready to continue ? (y or n) ? y

Delete configuration now ? (y or n) ? y

Configuration deleted

</pre>

h3. firmware booting

<pre>

Booting Image from Flash ROM

Checking image ... OK

Writing image to RAM (Release 6.2.5) .............................................................................................................................. OK (3990772 bytes)

Booting BOSS...

boss image started at 0x212400

BOSS PPC kernel v2.0 (X1200)

Copyright (c) 1999-2000 by BinTec Communications AG

Version V.6.2 Rev. 5 (Patch 1) IPSec V. 2.1.1 from 2002/10/17 00:00:00

The system is coming up.

Speed index... 49.81 MIPS

The system is ready.

AUTOEXEC:

  1     date Sat May 28 21:42:55 2016 done

  1     configd   SystemId: X1B120000370449  Cfg: (default) done

  10    isdnd background

  11    isdnautocf background

  20    x25swd background

  21    mpxd background

  50    ipd background

  51    snmpd background

  51    telnetd background

  51    syslogd background

  51    minipadd background

  51    txd background

  67    pppxd background

  68    pppoed background

  69    tud background

  70    radiusd background

  70    pppd background

  90    timed background

  97    ipalived background

  98    statusd background

  99    bootpd background

  99    ddnsd background

  99    traced background

  99    dnsd background

  99    resolvd background

  99    isdnlogind background

  99    vcapid background

  99    ipsecd background

</pre>