Bintec X1200 » History » Revision 3
Revision 2 (laforge, 10/23/2022 12:30 PM) → Revision 3/6 (laforge, 10/23/2022 01:48 PM)
h1. Bintec X1200
The Bintec X1200 is a ISDN router featuring two ISDN BRI lines on the WAN side and a single ethernet connecton on the LAN side.
It apparently supports remote CAPI (CAPI over TCP).
h2. Hardware
* Motorola XPC860DTZP50D3 PowerPC processor
* Samsung K4S643232C-TC10 SDRAM
* Sharp LH28F016SCHT-L95 Flash
* Infineon PSB2115H V1.1 IPAC ISDN Interface IC
* Lucent LU3x31FT2J80 Ethernet Transceiver IC
* LevelOne LXT905LC Ethernet PHY
* Maxim MAX202ECWE RS232 trasnceiver IC
* Maxim DS1314S NVRAM controller IC
* 5.5V 1.0F supercap (for NVRAM)
h2. Serial Console
h3. Power up
<pre>
### X1200 (Hardware-Rev. 1.2, Firmware-Rev. 6.0) ###
CPU Check ... passed (MPC 8XXT D3)
SDRAM Check ........ passed (8 MByte)
FLASH Check .. passed (2 MByte)
ISDN Check ... passed
100BT Check ... passed
10BT Check ... passed
### Selftest passed ###
Press <sp> for boot monitor or any other key to boot system
</pre>
h3. Bootmonitor
<pre>
X1200 Bootmonitor V.6.2 Rev. 8 from 2003/01/23 00:00:00
Copyright (c) 1999-2002 by BinTec Communications AG
(1) Boot System
(2) Software Update via TFTP
(3) Software Update via XMODEM
(4) Delete Configuration
(5) Default Bootmonitor Parameters
(6) Show System Information
Your Choice> 6
### Start System information ###
Identification: BINTEC X1000
Hardware: 1.2
Serial: X1B120000370449
Ethernet MAC 100BT: 00:a0:f9:02:4b:70
Flash: 2047 K/byte
RAM: 8127 K/byte
### Current Software
Logik: 6.0
Bootmon: V.6.2 Rev. 8 from 2003/01/23 00:00:00
Boss: 6.2.5
### more info
ID: X1B
Name: X1200
Company (short): BINTEC
Type: X1200
Company (long): BinTec Communications AG
Features: 0
### End System information ###
<pre>
<pre>
Your Choice> 4
Deleting the configuration will reset your router to factory state.
Ready to continue ? (y or n) ? y
Delete configuration now ? (y or n) ? y
Configuration deleted
</pre>
h3. firmware booting
<pre>
Booting Image from Flash ROM
Checking image ... OK
Writing image to RAM (Release 6.2.5) .............................................................................................................................. OK (3990772 bytes)
Booting BOSS...
boss image started at 0x212400
BOSS PPC kernel v2.0 (X1200)
Copyright (c) 1999-2000 by BinTec Communications AG
Version V.6.2 Rev. 5 (Patch 1) IPSec V. 2.1.1 from 2002/10/17 00:00:00
The system is coming up.
Speed index... 49.81 MIPS
The system is ready.
AUTOEXEC:
1 date Sat May 28 21:42:55 2016 done
1 configd SystemId: X1B120000370449 Cfg: (default) done
10 isdnd background
11 isdnautocf background
20 x25swd background
21 mpxd background
50 ipd background
51 snmpd background
51 telnetd background
51 syslogd background
51 minipadd background
51 txd background
67 pppxd background
68 pppoed background
69 tud background
70 radiusd background
70 pppd background
90 timed background
97 ipalived background
98 statusd background
99 bootpd background
99 ddnsd background
99 traced background
99 dnsd background
99 resolvd background
99 isdnlogind background
99 vcapid background
99 ipsecd background
</pre>
h2. Default login credentials after erasing config
User: @admin@, Password: @bintec@