Bintec X1200¶

The Bintec X1200 is a ISDN router featuring two ISDN BRI lines on the WAN side and a single ethernet connecton on the LAN side.

It apparently supports remote CAPI (CAPI over TCP).

Hardware¶

• Motorola XPC860DTZP50D3 PowerPC processor
• Samsung K4S643232C-TC10 SDRAM
• Sharp LH28F016SCHT-L95 Flash
• Infineon PSB2115H V1.1 IPAC ISDN Interface IC
• Lucent LU3x31FT2J80 Ethernet Transceiver IC
• LevelOne LXT905LC Ethernet PHY
• Maxim MAX202ECWE RS232 trasnceiver IC
• Maxim DS1314S NVRAM controller IC
• 5.5V 1.0F supercap (for NVRAM)

Serial Console¶

Power up¶

### X1200 (Hardware-Rev. 1.2, Firmware-Rev. 6.0) ###

CPU   Check ... passed (MPC 8XXT D3)
SDRAM Check ........ passed (8 MByte)
FLASH Check .. passed (2 MByte)
ISDN  Check ... passed
100BT Check ... passed
10BT  Check ... passed

### Selftest passed ###

Press <sp> for boot monitor or any other key to boot system

Bootmonitor¶

X1200 Bootmonitor V.6.2 Rev. 8 from 2003/01/23 00:00:00
Copyright (c) 1999-2002 by BinTec Communications AG

(1) Boot System
(2) Software Update via TFTP
(3) Software Update via XMODEM
(4) Delete Configuration
(5) Default Bootmonitor Parameters
(6) Show System Information

Your Choice> 6

### Start System information ###
Identification:              BINTEC X1000
Hardware:                    1.2
Serial:                      X1B120000370449
Ethernet MAC 100BT:          00:a0:f9:02:4b:70
Flash:                        2047 K/byte
RAM:                          8127 K/byte
### Current Software
Logik:                       6.0
Bootmon:                     V.6.2 Rev. 8 from 2003/01/23 00:00:00
Boss:                        6.2.5
### more info
ID:                          X1B
Name:                        X1200
Company (short):             BINTEC
Type:                        X1200
Company (long):              BinTec Communications AG
Features:                    0
### End System information ###
<pre>

<pre>
Your Choice> 4
Deleting the configuration will reset your router to factory state.
Ready to continue ? (y or n) ? y
Delete configuration now ? (y or n) ? y
Configuration deleted
</pre>

h3. firmware booting

<pre>
Booting Image from Flash ROM
Checking image ... OK
Writing image to RAM (Release 6.2.5) .............................................................................................................................. OK (3990772 bytes)
Booting BOSS...
boss image started at 0x212400

BOSS PPC kernel v2.0 (X1200)
Copyright (c) 1999-2000 by BinTec Communications AG
Version V.6.2 Rev. 5 (Patch 1) IPSec V. 2.1.1 from 2002/10/17 00:00:00

The system is coming up.

Speed index... 49.81 MIPS

The system is ready.

AUTOEXEC:
  1     date Sat May 28 21:42:55 2016 done
  1     configd   SystemId: X1B120000370449  Cfg: (default) done
  10    isdnd background
  11    isdnautocf background
  20    x25swd background
  21    mpxd background
  50    ipd background
  51    snmpd background
  51    telnetd background
  51    syslogd background
  51    minipadd background
  51    txd background
  67    pppxd background
  68    pppoed background
  69    tud background
  70    radiusd background
  70    pppd background
  90    timed background
  97    ipalived background
  98    statusd background
  99    bootpd background
  99    ddnsd background
  99    traced background
  99    dnsd background
  99    resolvd background
  99    isdnlogind background
  99    vcapid background
  99    ipsecd background
</pre>

h2. Default login credentials after erasing config

User: @admin@, Password: @bintec@