Retronetworking

h1. Stollmann TA+POC

{{TOC}}

ISDN Modem/TerminalAdapter.

Multiple hardware revisions exist.

h2. Hardware (Rev3)

|Supply Voltage|5V DC|

|Power Consumption|~2.1W|

|RS232 Connector|DB9|

|ISDN Line Connector|RJ45|

h2. Pictures

{{thumbnail(Stollmann-TA-POC-case-front1.jpg)}}

{{thumbnail(Stollmann-TA-POC-case-back.jpg)}}

{{thumbnail(Stollmann-TA-POC-case-bottom1.jpg)}}

{{thumbnail(Stollmann-TA-POC-pcb-perspective-front1.jpg)}}

{{thumbnail(Stollmann-TA-POC-pcb-perspective-back1.jpg)}}

{{thumbnail(Stollmann-TA-POC-pcb-top1.jpg)}}

{{thumbnail(Stollmann-TA-POC-pcb-bottom1.jpg)}}

Label:

<pre>

TA+POC

S/N 101322

HW: V3/8Mbit

FW: 5.340

Art. No: 935-51529

Stollmann E+V GmbH

</pre>

h2. AT-Commands

<pre>

ATI

TA+POC

OK

OK

ATI1

64

OK

ATI2

OK

ATI3

V5.340

OK

ATI4

Stollmann E+V GmbH

OK

ATI5

0-DSS1

OK

ATI6

(c) Copyright Stollmann E+V GmbH

OK

ATI7

OK

ATI9

($STO1004\1234AB89\MODEM\STO1004\TA+POC2E)

OK

ATI77

BOOT LOADER V1.12 201098 030E-02-00

OK

ATI99

POCa000 V5.340 Feb 11 2000 16:45:28

OK

</pre>

<pre>

at**help

cm

 g711law      Analog encoding law

conf

 enhanced     

 save         store parameter setting

 load         load stored parameter set

 go           exit configurator

 exit         exit configurator

 quit         exit configurator

 reset        force hardware reset

 defa         setup default parameter

 fwload       load new firmware

 fwstart      start new firmware

 show         display actual parameter

 help         display all commands

 ver          display version number

 showall      display enhanced parameter

 date         

 debloc       

remote

 rmsn         msn for remote access

 rsub         subaddress for remote access

 rpwd         password for remote access

 racctab      display remote access table incoming calls (msn/sub)

 racctab1     

 racctab2     

 racctab3     

 racctab4     

 racctab5     

trc

 trcdln       length of trace buffer entry

 trcmsk       trace mask

 trcon        start trace

 trcoff       stop trace

 trcclr       clear trace buffer

 trcread      read trace buffer

 trclog       log trace buffer

cim

 cmds         select command interface

 rsttim       Startup delay timer after reset

 rstmsg       Startup message after reset

dialci

 mode         select operation mode

 status       display status of serial and ISDN interface

 acctab       display access table incoming calls (msn/sub)

 typ          

 isdn         D channel protocol

 ptp          point to point mode

 s0led        BRI activation mode

 ringtimer    ring interval (100ms)

 rmmsg        indicate remote connection

 txfwd        data forwarding timer (t=x*50ms)

 acctab1      allow incoming call no/sub

 acctab2      allow incoming call no/sub

 acctab3      allow incoming call no/sub

 acctab4      allow incoming call no/sub

 acctab5      allow incoming call no/sub

 xtab         display xtab table (xxx)

 xtab1        set X.25 addr, isdnno

 xtab2        set X.25 addr, isdnno

 xtab3        set X.25 addr, isdnno

 xtab4        set X.25 addr, isdnno

 xtab5        set X.25 addr, isdnno

 catab        display hotline table (msn/sub)

 catab1       

 catab2       

 catab3       

atparam

 ats2         

 ats3         

 ats4         

 ats5         

 ats6         

 ats7         

 ats91        

 atopt        

 atrcs        

 atrej        

 s10          

 send3p       

x3param

 p001         

 p002         

 p003         

 p004         

 p005         

 p006         

 p007         

 p008         

 p009         

 p010         

 p011         

 p012         

 p013         

 p014         

 p015         

 p016         

 p017         

 p018         

 p019         

 p020         

 p021         

 p022         

dial

 cau          last cause of data call

 msn          msn = isdnno./subaddr

 sub          

 llc          llc incoming and outgoing

 hlc          hlc incoming and outgoing

 bc           bc incoming and outgoing

 prot         B channel protocol

 cha          charging information

 chatol       accumulated charging information

 ats0         AT: rings to answer

 brn          network baudrate

 bsize        frame length, valid range 16...2048

 br           serial baudrate

 dbits        databits (7,8)

 sbits        stopbits (1,2)

 prty         parity

 cdtr         DTR control

 cdcd         DCD control

 ccts         CTS control

 cdsr         DSR control

 flc          flow control

 idle         data timeout for disconnect

 cmlp         control multilink PPP

 chappwd      CHAP password

 v25bisout    enable/disable connect message from V.25bis

 v110llc      send V110 LLC

 v110flc      enable disable V110 flow control

 npl          ISDN Numbering Plan

 bod          bandwidth on demand

 bodiv        bod increase value

 bodit        bod increase time

 boddv        bod decrease value

 boddt        bod decrease time

 tdi          timer delay incoming

 cmds2        Subcommandset

OK

at**mode?

select operation mode

    0 - AT-V.110

    1 - V.25bis-V.110

    2 - X.3-X.25 B

    3 - X.3-X.31 D

OK

at**status

Current status information TA+POC

serial line: DTR:on, RTS:on, DSR:on, CTS:on, DCD:off, RI:off

ISDN: L1:up

Dch: Prot:DSS1 State:disconnected, CdPN:, CgPN:, prev error: 0 

Bch: Prot:V.110 State:disconnected, CdPN:, CgPN:

OK

at**isdn

0-DSS1

OK

at**isdn?

D channel protocol

    0 - DSS1

    1 - 1TR6

OK

at**show

cm

 g711law: 0-Automatic       

remote

 rmsn: *                     rsub: *                     rpwd: 

trc

 trcdln: 256   trcmsk: 0000000300020500   

cim

 cmds: 0-ATcmd

dialci

 isdn: 0-DSS1  ptp: 0-P-MP  

dial

 msn: *                      sub: *                      prot: 0-V.110 cha: 1

 chatol: 2737  brn: 0-adaptive             bsize: 2048   br: 0-adaptive

 dbits: 8      sbits: 1      prty: 0-none  cdtr: 2-control

 cdcd: 1-connected           ccts: 1-on    cdsr: 0-on    flc: 3-RTS/CTS

 idle: 0       cmlp: 0       chappwd: 

 v25bisout: 0  v110llc: 1    v110flc: 1    npl: 80       bod: 0

 bodiv: 40     bodit: 30     boddv: 40     boddt: 30     tdi: 0

 cmds2: 0     

OK

at**showall

cm

 g711law: 0-Automatic       

remote

 rmsn: *                     rsub: *                     rpwd: 

 racctab1:                                               racctab2: 

 racctab3:                                               racctab4: 

 racctab5:                                              

trc

 trcdln: 256   trcmsk: 0000000300020500   

cim

 cmds: 0-ATcmd rsttim: 40    rstmsg: 0    

dialci

 isdn: 0-DSS1  ptp: 0-P-MP   s0led: 1      ringtimer: 50 rmmsg: 0

 txfwd: 1      acctab1:                    acctab2: 

 acctab3:                    acctab4:                    acctab5: 

 xtab1:                                                  xtab2: 

 xtab3:                                                  xtab4: 

 xtab5:                                                  catab1: 

 catab2:                                                 catab3: 

atparam

 ats2: 43      ats3: 13      ats4: 10      ats5: 8       ats6: 3

 ats7: 30      ats91: 0      atopt: 25     atrcs: 4      atrej: 0

 s10: 0        send3p: 1    

x3param

 p001: 0       p002: 0       p003: 0       p004: 5       p005: 0

 p006: 69      p007: 8       p008: 0       p009: 0       p010: 0

 p011: 0       p012: 0       p013: 0       p014: 0       p015: 0

 p016: 0       p017: 0       p018: 0       p019: 0       p020: 0

 p021: 0       p022: 0      

dial

 msn: *                      sub: *                      llc: 

 hlc:                        bc: 8890                    prot: 0-V.110 cha: 1

 chatol: 2737  ats0: 1       brn: 0-adaptive             bsize: 2048

 br: 0-adaptive              dbits: 8      sbits: 1      prty: 0-none

 cdtr: 2-control             cdcd: 1-connected           ccts: 1-on

 cdsr: 0-on    flc: 3-RTS/CTS              idle: 0       cmlp: 0

 chappwd:                                  v25bisout: 0  v110llc: 1

 v110flc: 1    npl: 80       bod: 0        bodiv: 40     bodit: 30

 boddv: 40     boddt: 30     tdi: 0        cmds2: 0     

OK

</pre>