BildTel 001 » History » Revision 13
« Previous |
Revision 13/27
(diff)
| Next »
laforge, 10/30/2023 08:19 PM
- Table of contents
- BildTel 001
BildTel 001¶
The Telekom-branded BildTel 001 was likely the first commercially available ISDN video phone in Germany.
(Only digital marketing picture I could find online, courtesy of Picture Allianze / Matthias Hiekel)
Architecture¶
The system consists of the following parts:- A TV screen with built-in BTX decoder (inherited from LOEWE_Multitel_TV10)
- A keyboard + phone-receiver combo (inherited from LOEWE_Multitel_TV10)
- A desktop-computer-like box called the Codec (containing the actual ISDN video telephony part, implemented by AEG/OLYMPIA)
- A video camera
The BTX Terminal LOEWE_Multitel_TV10 was used as the "user interface" for the device, adding the codec box to turn it into a video phone.
Codec unit¶
The Codec unit ("Bildeinheit") consists of a variety of different circuit boards:- 1x power supply
- 4x "mainboards" stacked on top of each other (two sandwiches of two PCBA)
- boards have a number of DIN 41612 slots for plug-in cards
- 9x CODEC ADSP boards plugged into slots of the top two mainboards
- 1x OUTDIG sandwich, consisting of two PCBA plugged into slots of the top mainboard
- this is the TV output board, generating and digital-analog-converting analog TV signal
- 1x FIXME sandwich, consisting of two PCBA plugged into slots of a mainboard
- this is the camera input board, receiving and digitizing the analog TV camera signal
AEG-OLYMPIA CODEC ADSP¶
This board exists 9 times in total. There are no visible differences between the boards; also the label on the GAL is identical.
PCB Marking: 1601914L11T
Connector Marking: None
ADI ADSP-2101 | Digital Signal Processor |
VX-8111 10.0000 MHz | Crystal Oscillator |
GAL20V8A (4012-001/2) | GAL |
2x IDT 7201SA25J | FIFO |
2x IDT 7202SA25J | FIFO |
3xCY7C199-45VC | RAM |
AEG-OLYMPIA OUTDIG¶
PCB Marking: 2401913L1T
Connector Marking: 35.103-3030.2 SN. 3051
top PCBA:
Brooktree Bt101 | Triple 8-bit VIDEODAC |
Xilinx XC2018-100 | FPGA 100 CLBs, 1000 Gates |
S-Data SXO-300C 27.00000 MHz | Crystal Oscillator |
3x IDT 7201SA25J | FIFO |
bottom PCBA: FIXME
TV Camera¶
TV / BTX Unit¶
BTX decoder¶
- EPROM image: bildtel001_tv10_btxdecoder_16772_074_349_27C010.bin
Keyboard/receiver unit¶
Actual Cherry keyboard PCBA after full disassembly, ultrasonic cleaning of all keycaps and lots of isopropanol on the PCB, removing what might be decades old coke residue:
Connections¶
Codec unit¶
- connects to ISDN basic-rate S0 interface using 8P8C/RJ45 plug
- has two proprietary connectors for attaching video cameras
- has two SCART connectors (one for audio/video output to the TV)
- has a TAE jack for attaching an analog phone for the audio port (connected to the combined keyboard/receiver unit by default)
- has another TAE jack (purpose unknown)
- has a V.24 interface on a SUB-D 9 connector which connects to the built-in BTX decoder of the TV unit
TV Camera¶
- connects to the Codec unit using a proprietary high-density connector that appears to carry both video and power
TV unit¶
- has an RF input for TV broadcast signals (PAL)
- has a SCART input for baseband audio/video from peripherals (like the Codec unit)
- has a DIN speaker output for attaching an external speaker
- has a built-in BTX decoder with
- an unused DIN port intended to connect to the DBT-03 BTX-Modem (not used in the ISDN video application)
- an unused centronics port
- an auxiliary V.24 port on a DIN connector interfacing the SUB-D 9 of the Codec unit
Keyboard/receiver unit¶
- has a cable with TAE connector attached (connects to codec unit)
Further Reading¶
Updated by laforge 9 months ago · 13 revisions